Resources
In a gravimetric standardization analysis, a student dissolves an unknown sample of impure iron ore weighing in excess hydrochloric acid, converting all iron into soluble . Excess aqueous ammonia is added to precipitate iron(III) hydroxide: . The precipitate is filtered, dried, and ignited in a muffle furnace to yield pure hematite: . If the isolated dry has a mass of , apply the conservation of iron atoms (conservation of mass) to calculate: (a) the total mass of elemental in the original ore sample, and (b) the mass percentage of iron in the ore.
Answer and steps
Final answer
(a) Molar mass of ; Molar mass of ; ; (b) .
Steps
Calculate the Molar Masses
Principle: Conservation of Mass and Atoms
By the law of conservation of mass, all iron atoms present in the original ore sample are quantitatively converted through the chemical reactions into iron(III) oxide, . Therefore:
Using standard atomic weights:
- Atomic weight of iron,
- Atomic weight of oxygen,
The molar mass of hematite () is:
(a) Calculate the Total Mass of Elemental
Each mole of contains of atoms. The gravimetric factor representing the mass fraction of in is:
Using the measured mass of dry ():
Common Pitfall: A frequent error is forgetting the stoichiometric coefficient of for iron. Since there are two iron atoms per formula unit of , omitting the factor of will underestimate the iron content by half.
(b) Calculate the Mass Percentage of in the Ore
The original ore sample has a total mass of . The mass percent of iron is:
Typical errors
01 The student forgets that each mole of Fe2O3 contains 2 moles of Fe, using a 1:1 mole ratio instead of 2:1.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
Each mole of contains of atoms because of the chemical formula subscript. You multiplied the moles of directly by the atomic weight of iron without multiplying by .
- Step 3Correct
You set up the mass percentage ratio correctly, but your final answer is exactly half of the correct percentage due to the omitted stoichiometric factor of in the previous step.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the molar mass of as .
You converted the measured mass of to moles correctly.
You set up the mass percent formula using the original ore sample mass accurately.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou overlooked the chemical formula subscript in , treating the mole ratio of to as rather than converting into .
REASONING PATH
Your ACEpath teacher’s suggested approach- Formula Subscript Inspection
In gravimetric conversions, .
Always inspect the chemical formula of the weighing form and write out the explicit molar ratio factor before calculating element mass.
CORRECTED PATH
ACEpath Teacher's Demonstration(a) ; (b)
02 The student calculates the mass percentage relative to the mass of Fe2O3 recovered rather than the initial ore sample mass.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You divided by (the mass of the ignited product), which calculates the mass percent of iron in pure hematite rather than in the original ore sample.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the molar mass of .
You correctly used the gravimetric factor with the stoichiometric coefficient of for to find of iron.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou accidentally placed the mass of the precipitate in the denominator instead of the mass of the original ore sample.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the analyte matrix (the impure raw ore sample) with the final gravimetric weighing form (the pure isolated precipitate). In gravimetric analysis, the mass percentage of the analyte in the unknown sample must always be evaluated relative to the initial mass of that unknown sample.
REASONING PATH
Your ACEpath teacher’s suggested approach- Distinguish Sample from Weighing Form
Before computing a percentage, circle the initial mass of the impure sample given at the start of the problem and ensure it is placed in the denominator.
CORRECTED PATH
ACEpath Teacher's DemonstrationIdentify the original ore sample mass: .
Set up the mass percent ratio relative to the ore: .
Evaluate the final percentage: .
(a) ; (b)
03 The student miscalculates the molar mass of Fe2O3 by omitting the subscript for iron, calculating it as FeO3.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
= 55.85 + 3 16.00 = 103.85
Correct= 2(55.845) + 3(16.00) = 159.69
You omitted the subscript 2 for iron in the formula . A formula unit contains two iron atoms, so its molar mass is .
- Step 2
= 0.5215 = 0.5609
Correct= 0.5215 = 0.3648
You correctly accounted for the per mole of in the numerator, but substituting the incorrect molar mass yielded of , which is impossible because an element's mass cannot exceed the total mass of the compound ().
- Step 3
= 100% = 38.68%
Correct= 100% = 25.16%
You applied the percentage formula correctly, but the result is inaccurate due to carrying forward the incorrect mass of iron.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified that each mole of contains two moles of elemental .
You correctly structured the gravimetric factor to convert precipitate mass into elemental mass.
You correctly applied the mass percentage formula relative to the initial ore sample.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou forgot to multiply the atomic weight of iron by its stoichiometric subscript 2 when summing the formula mass of , treating the compound as instead.
REASONING PATH
Your ACEpath teacher’s suggested approach- Subscript Accounting
Every subscript in a chemical formula multiplies the molar mass of the preceding element or group.
Check each element against the chemical formula when computing formula weight: .
- Gravimetric Factor Sanity Check
The gravimetric factor for an element inside a pure neutral compound must always be less than ().
Always verify that the mass fraction . If the resulting elemental mass exceeds the precipitate mass, check the denominator.
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate the correct molar mass of : .
Recalculate the mass of iron using the corrected gravimetric factor: .
Compute the mass percent of iron in the original ore sample: .
(a) Mass of ; (b) Mass % of
Lock it in
In gravimetric analysis, how do you find the moles of an element inside a compound with formula ?
Multiply the moles of compound by the subscript : .
Similar question
A sample of limestone containing calcium is dissolved and precipitated as calcium oxalate, which is ignited to pure calcium oxide, (). If of is obtained, find the mass of elemental calcium () and its mass percentage in the limestone.
Answer
; .
In a gravimetric sulfate determination, sulfur in a organic sample is oxidized to sulfate and precipitated as barium sulfate, (). If the dry precipitate weighs , calculate the percentage of sulfur () in the sample.
Answer
; ; .
An unknown copper alloy weighing is analyzed gravimetrically by dissolving and precipitating copper as cuprous thiocyanate, followed by ignition to copper(I) oxide, (). If of pure is recovered, calculate the mass percentage of copper () in the alloy.
Answer
Each mole of contains . ; .