Resources
In an analytical chemistry laboratory, a student conducts a conductometric titration to verify the purity of an unbuffered aqueous solution of iron(II) sulfate (). A aliquot of the solution is titrated with barium hydroxide () while stirring continuously at . The overall chemical reaction is: . Both reaction products are insoluble precipitates. (a) Sketch the profile of electrical conductivity as a function of the volume of added from to beyond the equivalence point (), identifying the state of ions in solution at each stage. (b) If the minimum in electrical conductivity occurs at exactly of , calculate the initial molar concentration of in the sample.
Answer and steps
Final answer
(a) Initial conductivity is high due to dissociated ions and . As is added, and precipitate out both original ions as insoluble and , causing the conductivity to drop linearly to a near-zero minimum at the equivalence point (). Beyond the equivalence point, continuing addition of titrant introduces excess unreacted and ions, causing electrical conductivity to rise linearly. (b) Initial concentration .
Steps
Part (a): Profile of Electrical Conductivity
Electrical conductivity in an aqueous solution depends directly on the concentration and mobility of free dissolved ions.
- Before Adding Titrant (): The initial solution contains fully dissociated : Because a high concentration of mobile divalent ions ( and ) is present, the initial electrical conductivity is relatively high.
- Pre-Equivalence Region (): As solution is added, the following precipitation reaction takes place: Both products are insoluble salts. As a result, the added and remove the dissolved and ions from the solution as solids, rather than replacing them with other spectator ions. Consequently, the total concentration of mobile ions decreases steadily, causing the conductivity to drop linearly.
- At the Equivalence Point (): Stoichiometric amounts of and have reacted. Virtually all and ions are removed from solution. The only ions remaining are trace amounts from water dissociation and the extremely low equilibrium concentrations determined by the solubility products () of and . Therefore, the conductivity reaches a distinct, sharp minimum near zero.
- Post-Equivalence Region (): Any additional does not react because the has been completely consumed. The newly introduced and highly mobile ions accumulate as free ions in solution: This causes the electrical conductivity to rise linearly as more titrant is added up to .
Summary Profile: The titration curve forms a symmetric V-shape, starting at a high conductivity value, decreasing linearly to a near-zero minimum at , and then rising linearly beyond the equivalence point.
Part (b): Calculation of Initial Concentration
- Reaction Stoichiometry: From the balanced equation: The stoichiometric ratio of to is .
- Moles of Consumed at Equivalence:
- Initial Molar Concentration of : Because of the mole ratio: Dividing by the initial aliquot volume ():
Typical errors
01 The student forgets that Ba(OH)₂ is a diprotic base providing two moles of hydroxide per formula unit and incorrectly divides by 2 assuming a 1:2 stoichiometry for FeSO₄ to Ba(OH)₂.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
Conductivity starts high due to and ions. Conductivity drops to near zero at the equivalence point as and precipitate. Conductivity increases past the equivalence point due to excess and ions.
- Step 2
- Step 3Correct
You divided by , likely because supplies two hydroxide ions per formula unit. However, iron(II) is divalent (), so each mole of requires two moles of . The overall balanced equation shows a stoichiometric mole ratio between and .
- Step 4Correct
You carried out the concentration formula correctly, but your result was halved because of the stoichiometric error in Step 3.
WHAT YOU DID WELL
Compliments from Your TeacherYou clearly explained the ionic changes that govern conductivity at each stage of the titration.
You correctly converted units and calculated the moles of barium hydroxide consumed at the equivalence point.
You set up the final molar concentration quotient properly using the initial sample volume.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeDividing the moles of titrant by 2 when determining the moles of iron(II) sulfate.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou likely associated the subscript 2 in with a reactant ratio, confusing this reaction with acid-base titrations of monoprotic acids (such as with ). Because is a cation, one formula unit of requires both ions and the single ion from one formula unit of , yielding an exact mole ratio.
REASONING PATH
Your ACEpath teacher’s suggested approach- Verify Balanced Equation Coefficients
In titration stoichiometry, the mole ratio of reactants is determined strictly by the coefficients of the balanced overall equation, not by the charge or subscript of an individual ion alone.
Always inspect the balanced equation before dividing or multiplying mole quantities.
CORRECTED PATH
ACEpath Teacher's DemonstrationFrom the balanced equation , the stoichiometric ratio is .
Set .
Divide by the aliquot volume: .
02 The student inverts the dilution ratio by dividing by the volume of titrant rather than the original sample volume.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
a) Conductivity decreases prior to equivalence as and form insoluble and . ⟹ b) At the equivalence point, conductivity reaches a minimum near zero. ⟹ c) Conductivity rises after equivalence due to excess and ions.
- Step 2
- Step 3Correct
You divided the moles of by the volume of titrant added () instead of the initial aliquot volume of the analyte ().
WHAT YOU DID WELL
Compliments from Your TeacherYou clearly explained how ion removal and ion accumulation dictate electrical conductivity before, at, and after the equivalence point.
You correctly computed the moles of titrant added using its concentration and equivalence volume.
You correctly used the stoichiometric ratio from the balanced precipitation equation.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeDividing analyte moles by titrant volume instead of the sample aliquot volume.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou associated the calculated quantity of substance with the volume measured from the burette rather than matching moles of analyte to the volume of the original analyte solution.
REASONING PATH
Your ACEpath teacher’s suggested approach- Match Moles to Corresponding Volume
Molar concentration of an analyte sample is always , where is the volume of the original solution pipetted.
Always label your volumes explicitly as and before substituting into concentration formulas.
CORRECTED PATH
ACEpath Teacher's DemonstrationIdentify the original volume of the sample: .
Divide the moles of by the sample volume: .
03 The student mistakenly believes conductivity remains constant before the equivalence point by assuming spectator counter-ions maintain charge neutrality in solution instead of precipitating.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
Before equivalence, conductivity remains constant because ions in solution are replaced at equal charge.
CorrectConductivity decreases linearly from an initial high value toward near zero because and ions are simultaneously precipitated out as insoluble and , leaving virtually no mobile ions in solution.
You assumed ions were being replaced by spectator ions of equivalent charge. In this specific precipitation reaction, both the cation and the anion combine with titrant ions to form solid precipitates, which directly reduces the total concentration of free ions in solution.
- Step 2
At equivalence, conductivity is at a steady baseline. ⟹ After equivalence, conductivity rises steeply due to excess and .
- Step 3
⟹ ⟹
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly determined that excess and ions cause conductivity to rise after the equivalence point.
You correctly applied the mole ratio between and .
You calculated the volume conversion and initial molar concentration of with complete mathematical accuracy.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakenone
WHY IT HAPPENED
ACEpath Teacher's DiagnosisTreating a double-precipitation reaction as an ion-replacement process where spectator ions maintain constant net charge, failing to recognize that removing all dissolved ions removes all charge carriers.
REASONING PATH
Your ACEpath teacher’s suggested approach- Identify Net Ionic Species
Electrical conductivity in an aqueous electrolyte solution is proportional to the total concentration and molar conductivity of mobile, dissolved ions: . Neutral solids contribute zero conductivity.
Check whether reaction products are soluble electrolytes or precipitates before determining whether dissolved ion counts increase, decrease, or stay constant.
CORRECTED PATH
ACEpath Teacher's DemonstrationIdentify the net ionic equation: .
Since both products are solids, each aliquot of titrant added consumes free and without leaving any spectator ions in solution.
Conclude that conductivity drops linearly from the initial value to a sharp minimum near zero at , forming a V-shaped curve.
(a) The conductivity curve is V-shaped: it drops linearly from a high value at to a near-zero minimum at as ions precipitate as and , then rises linearly to due to excess and . (b) .
Lock it in
In the precipitation reaction , what is the stoichiometric mole ratio of to ?
. Both and are divalent, so one formula unit of supplies exactly the ions needed to precipitate one formula unit of .
Similar question
A solution of copper(II) sulfate () is titrated with , precipitating both and . The conductivity minimum occurs at . Calculate the initial molar concentration of .
Answer
. Key steps: . Because and react with , . Then .
In a conductometric titration, of an iron(III) sulfate solution, , requires of to reach minimum conductivity. Write the balanced equation and find .
Answer
. Key steps: Balanced equation is . Moles of . Mole ratio is , so . Concentration .
A student titrates a mixture containing of and of with . Both precipitate , while also precipitates. What total volume (in ) of titrant is required to reach the overall conductivity minimum?
Answer
. Key steps: reacts with in a ratio: , consuming . also reacts : , consuming . Total needed . Volume .