Resources
An industrial wastewater sample contains lead(II) nitrate (, molar mass ) at a trace concentration of (defined as ). Assuming the density of the wastewater is , convert this concentration into: (a) mass percent concentration (), and (b) millimolarity ().
Answer and steps
Final answer
(a) , (b)
Steps
Define the components from the given concentration
To convert between different concentration units, choose a convenient basis for calculation, such as of solution.
The wastewater contains at (). For a basis of () of solution:
- Mass of solute, :
- Mass of solution:
Calculate the mass percent concentration ()
Mass percent is the ratio of solute mass to total solution mass multiplied by :
Substitute the values:
(Note: Because , multiplying by directly gives .)
Calculate the millimolarity ()
Millimolarity is defined as the millimoles of solute per liter of solution:
- Find the amount of solute in millimoles (): Using the molar mass of (, or ):
-
Find the volume of the solution in liters (): Use the density of the wastewater ():
Pitfall: Do not assume the solution has a density of exactly . Using the given density of is essential to account for the true volume.
- Calculate the concentration:
Typical errors
01 The student ignores the solution density and assumes 1 L of wastewater has a mass of exactly 1 kg, underestimating the molarity.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You assumed that of solution weighs exactly . Because the problem specifies a density of , you must use to find the true volume corresponding to of solution.
- Step 3Correct
Your conversion from mass to millimoles was set up correctly, but dividing by instead of led to an incorrect final millimolarity.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly interpreted as .
You successfully calculated the mass percent concentration as .
You used the correct molar mass to find the amount of solute in millimoles.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou defaulted to the approximation that aqueous solutions have a density of , overlooking that a non-unit density () was provided to convert between mass and volume.
REASONING PATH
Your ACEpath teacher’s suggested approach- Converting solution mass to solution volume
Whenever a non-unit solution density is given, solution volume must be calculated as .
Check the given parameters for density before equating of solution directly to .
CORRECTED PATH
ACEpath Teacher's DemonstrationChoose a basis of of wastewater solution.
Calculate volume: .
Calculate solute amount: .
Calculate millimolarity: .
(a) , (b)
02 The student divides the mass of solution by the density instead of multiplying by density when calculating the mass of 1 L of wastewater.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
To find the mass of a given volume, you must multiply volume by density (). Dividing by gave a volume-to-density ratio with inverted units instead of the true mass.
- Step 3Correct
Your calculation correctly applied the given concentration of , but the numeric result is affected by the incorrect solution mass from Step 2.
- Step 4Correct
Your method of dividing solute mass by molar mass to get millimoles per liter was entirely sound, but the final value reflects the propagated error from Step 2.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly converted parts per million into mass percent.
You correctly identified that corresponds to .
You correctly converted solute mass into millimoles using the given molar mass.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou divided by density instead of multiplying by density when calculating the mass of of wastewater.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou inverted the density relationship . Tracking dimensional units explicitly (such as ) avoids dividing volume by density when converting volume to mass.
REASONING PATH
Your ACEpath teacher’s suggested approach- Dimensional analysis check for density
()
Always carry units through calculations: , ensuring cancels out.
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate the true mass of of wastewater: .
Determine the mass of in : .
Convert solute mass to millimoles: .
State the final millimolarity: .
(a) , (b)
03 The student misinterprets parts per million as parts per hundred thousand, multiplying by 10^-5 instead of 10^-6.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You wrote () in the denominator instead of (). One million has six zeros, so equals .
- Step 2Correct
Your formula for mass percent was completely correct, but the result was shifted by a factor of due to the earlier fraction error.
- Step 3Correct
You correctly used density to find the mass of of solution, but carrying forward the ratio gave ten times the actual solute mass.
- Step 4Correct
You executed the mole conversion and concentration division accurately, but the value reflects the earlier decimal error.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly used the solution density to determine the total mass of of solution.
You correctly applied the formula for mass percent concentration.
You correctly converted mass in milligrams to millimoles using the molar mass as .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou counted five zeros (, one hundred thousand) instead of six zeros (, one million) when converting ppm to a fraction.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisMisidentifying the base power of ten for 'parts per million' as instead of , or forgetting the direct equivalence .
REASONING PATH
Your ACEpath teacher’s suggested approach- Define parts per million
Always write (or , with six zeros) in the denominator when expressing ppm as a pure ratio.
- Quick percent conversion
Convert ppm to mass percent directly by dividing by (multiplying by ).
CORRECTED PATH
ACEpath Teacher's DemonstrationExpress as .
Calculate mass percent: .
Find solute mass in () of solution: .
Calculate millimoles: .
Divide by to obtain .
(a) , (b)
Lock it in
How do you convert mass of solution () to volume of solution () when density () is provided?
. Never assume if a specific density value is given in the problem.
Similar question
A groundwater sample contains of ions (molar mass ). If the density of the water is , calculate the molarity () of .
Answer
(or ). Key steps: In (), there are of . ; .
An aqueous solution of sodium chloride (, molar mass ) has a concentration of and a density of . Calculate the millimolarity () of .
Answer
. Key steps: Basis solution: solute mass , amount . Solution volume . Concentration .
A concentrated brine solution has a density of and contains (molar mass ). Calculate: (a) the concentration in , and (b) the molarity in .
Answer
(a) ; (b) . Key steps: (a) . (b) Basis solution: solution mass . Mass of . Moles . Molarity .