Resources
An insulated calorimeter contains of liquid water and of ice in thermal equilibrium at the phase boundary temperature of . A piece of pure copper metal with mass is heated in an oven to and rapidly submerged into the calorimeter. Given the specific heat capacity of copper , the specific heat capacity of liquid water , and the enthalpy of fusion of water , determine whether the ice melts completely, and calculate the exact mass of ice remaining in grams at the final equilibrium state.
Answer and steps
Final answer
The ice does not melt completely; of ice remains.
Steps
Thermal equilibrium and available heat from copper
To determine whether the ice melts completely and find the remaining mass of ice, we analyze the heat exchange between the hot copper metal and the ice-water mixture inside the insulated calorimeter.
The calorimeter initially contains liquid water and ice at thermal equilibrium at . As long as both liquid water and ice coexist, the temperature of the mixture remains fixed at .
The maximum amount of heat released by the copper, , occurs if it cools from its initial temperature down to the mixture's phase-change temperature :
Heat required to melt all of the ice
The enthalpy of fusion of water is . The energy required to melt the entire initial mass of ice () is:
Determining if the ice melts completely
Comparing the energy available with the energy required:
Because the total heat supplied by cooling the copper to is less than the energy needed to melt all of the ice, the copper reaches thermal equilibrium at before all ice can melt.
Therefore, the ice does not melt completely, and the final equilibrium temperature of the system is .
Mass of ice melted and remaining
The heat transferred melts a portion of the ice, :
Using the effective thermal energy absorbed by the phase change:
Subtracting the mass of melted ice from the initial mass gives the mass of ice remaining:
Typical errors
01 A student might incorrectly assume the liquid water already in the calorimeter also absorbs heat and rises in temperature before all the ice melts, rather than recognizing the mixture stays at 0.00 °C until all ice is melted.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
You introduced a sensible heating term for liquid water and added the specific heat capacity to the enthalpy of fusion. As long as ice and liquid water coexist at thermal equilibrium, the mixture temperature is clamped at (). All transferred heat is absorbed exclusively as latent heat of fusion.
- Step 4Correct
Your subtraction step was executed cleanly, but your result was affected by the error in from Step 3.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the thermal energy released by the copper cooling to the phase boundary.
You correctly evaluated the latent heat needed to melt the entire initial mass of ice.
You correctly deduced that the ice does not melt completely.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou included a temperature increase for the liquid water even though solid ice was still coexisting with it at equilibrium.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou did not account for the principle of phase equilibrium clamping: as long as ice and liquid water coexist at constant pressure, any heat added goes entirely into melting the solid phase at a constant temperature of . Liquid water cannot warm above until every gram of ice has fully melted.
REASONING PATH
Your ACEpath teacher’s suggested approach- Temperature Clamping During Phase Change
During a solid-liquid phase transition of a pure substance at equilibrium, the temperature remains constant () until one of the phases completely disappears.
Check whether any solid ice remains before adding any sensible heat term for the liquid phase.
CORRECTED PATH
ACEpath Teacher's DemonstrationRecognize that because ice remains, the final equilibrium temperature is strictly , meaning .
Equate all available heat released by the cooling copper to the latent heat of fusion: .
Solve for the mass of ice melted: .
Subtract the melted mass from the initial mass of ice: .
The ice does not melt completely; of ice remains.
02 A student might divide the heat released from copper by the specific heat capacity of liquid water instead of the enthalpy of fusion of water when calculating how much ice melts.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3
- Step 4Correct
You divided the available energy by the specific heat capacity of liquid water () rather than the latent heat of fusion of ice (). Phase changes take place at constant temperature and depend on , not on .
- Step 5Correct
Because of the previous calculation error, your resulting melted mass exceeded the total initial mass of ice, causing a contradiction with your earlier correct conclusion that the ice does not melt completely.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly used the specific heat formula to compute the heat released by the copper.
You accurately calculated the energy required to melt the full mass of ice using .
You correctly concluded that the ice would not melt completely because .
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou selected the specific heat capacity of liquid water () instead of the enthalpy of fusion () when converting absorbed thermal energy into the mass of substance undergoing a phase change.
REASONING PATH
Your ACEpath teacher’s suggested approach- Phase change vs. temperature change
During a phase transition at constant temperature, heat transfer is governed by , whereas temperature changes within a single phase follow .
Always verify whether the heat causes a temperature shift or a phase transition before choosing between and .
- Check dimensional consistency
Dividing Joules () by yields , not grams ().
Include units in your calculations to ensure that .
CORRECTED PATH
ACEpath Teacher's DemonstrationUse the enthalpy of fusion to find the mass of ice melted: .
Subtract the melted mass from the initial ice mass: .
The ice does not melt completely; of ice remains (or based on workbook source rounding).
03 A student might calculate the mass of ice melted but report it as the remaining mass of ice instead of subtracting it from the initial mass.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3
- Step 4
- Step 5Correct
You equated the mass of ice that melted with the mass of ice remaining. The quantity is the amount that melted, so you must subtract it from the initial of ice.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the heat released by the cooling copper block.
You correctly calculated the total heat required to melt the entire mass of ice.
You correctly deduced that the ice does not melt completely because .
You correctly calculated the mass of ice melted during the heat transfer.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou solved for the mass of ice converted to liquid water, but wrote it down as the final remaining mass of ice without performing the final subtraction.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the quantity that changed () with the quantity that remains after the change ().
REASONING PATH
Your ACEpath teacher’s suggested approach- Define Mass Terms Clearly
In phase change calorimetry, .
Label and as distinct variables so you do not accidentally substitute one for the other.
- Sanity Check with Initial Values
The remaining mass must decrease from the initial value, and the sum of melted and remaining ice must equal the starting mass.
Always verify that before finalizing your answer.
CORRECTED PATH
ACEpath Teacher's DemonstrationApply the conservation of mass to find the remaining ice:
Substitute the values:
The ice does not melt completely; of ice remains.
Lock it in
What happens to the temperature of an insulated ice-water mixture at when a warm object is submerged into it, assuming not all of the ice melts?
The temperature remains strictly at . All heat transferred is used exclusively for the phase transition (melting ice), with zero temperature change in the liquid water.
Similar question
An insulated calorimeter contains of liquid water and of ice at . An aluminum block with mass () at is submerged. Given , determine whether the ice melts completely, and find the remaining mass of ice.
Answer
. Heat needed to melt all ice is . Since , the ice does not melt completely. Mass melted: . Mass of ice remaining: .
A iron sphere () is heated to and placed into an insulated beaker containing of water and of ice at . Determine if all the ice melts, and if so, calculate the final equilibrium temperature . (Use and ).
Answer
Heat to cool iron to : . Heat to melt all ice: . Since , all ice melts completely. Remaining excess heat: . Heat capacity of warmed system: . Final temperature: .
In a cryo-cooling experiment, an unknown mass of ice at is added to of liquid water at in an insulated cup. After reaching equilibrium, exactly of un-melted ice remains. Using and , determine the initial mass of ice added to the cup.
Answer
Because ice remains at equilibrium, the final temperature is . Heat lost by liquid water: . Mass of ice melted by this heat: . Initial mass of ice added: .