Resources

An electric heating element rated at 150 W150\text{ W} (1 W=1 J/s1\text{ W} = 1\text{ J}/\text{s}) operates for 3.50 minutes3.50\text{ minutes} with 88.0%88.0\% thermal efficiency to heat a 400 g400\text{ g} cylinder of pure aluminum (c=0.897 J/(g⋅∘C)c = 0.897\text{ J}/(\text{g}\cdot^\circ\text{C})). Calculate the total thermal energy transferred into the metal cylinder and its resulting temperature change ΔT\Delta T.

Answer and steps

Final answer

q=2.77×104 Jq = 2.77 \times 10^4\text{ J} (27.7 kJ27.7\text{ kJ}), ΔT=77.3∘C\Delta T = 77.3^\circ\text{C}

Steps

01

Calculate the total electrical energy produced

Power measures the rate of energy transfer: 1 W=1 J/s1\text{ W} = 1\text{ J/s}. First, convert the operating time from minutes to seconds:

t=3.50 min×60 s1 min=210 st = 3.50\text{ min} \times \frac{60\text{ s}}{1\text{ min}} = 210\text{ s}

Now, compute the total electrical energy supplied by the heating element:

Etotal=P⋅t=150 J/s×210 s=31 500 JE_{\text{total}} = P \cdot t = 150\text{ J/s} \times 210\text{ s} = 31\,500\text{ J}


02

Determine the thermal energy absorbed by the cylinder (qq)

Because the heating element has an efficiency of 88.0%88.0\%, only that fraction of the total energy is successfully transferred to the aluminum cylinder as heat:

q=η⋅Etotal=0.880×31 500 J=27 720 Jq = \eta \cdot E_{\text{total}} = 0.880 \times 31\,500\text{ J} = 27\,720\text{ J}

Rounding to three significant figures gives:

q=2.77×104 J(27.7 kJ)q = 2.77 \times 10^4\text{ J} \quad (27.7\text{ kJ})

Common Pitfall: Always account for efficiency before setting up the heat equation. Using the total energy (31 500 J31\,500\text{ J}) instead of the delivered heat (27 720 J27\,720\text{ J}) overestimates the temperature increase.


03

Calculate the resulting temperature change (ΔT\Delta T)

The relationship between absorbed heat, mass, specific heat capacity, and temperature change is given by the specific heat formula:

q=m⋅c⋅ΔTq = m \cdot c \cdot \Delta T

Rearranging the formula to solve for ΔT\Delta T:

ΔT=qm⋅c\Delta T = \frac{q}{m \cdot c}

Substitute the given values (m=400 gm = 400\text{ g}, c=0.897 J/(g⋅∘C)c = 0.897\text{ J}/(\text{g}\cdot^\circ\text{C}), and q=27 720 Jq = 27\,720\text{ J}):

ΔT=27 720 J400 g⋅0.897 J/(g⋅∘C)=27 720358.8∘C≈77.26∘C\Delta T = \frac{27\,720\text{ J}}{400\text{ g} \cdot 0.897\text{ J}/(\text{g}\cdot^\circ\text{C})} = \frac{27\,720}{358.8}^\circ\text{C} \approx 77.26^\circ\text{C}

Rounding to three significant figures yields:

ΔT=77.3∘C\Delta T = 77.3^\circ\text{C}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets to convert the operating time from minutes to seconds, resulting in an energy and temperature change that are 60 times too small.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    t = 3.50 min\text{ min}   ⟹  \implies E_{total\text{total}} = P ×\times t = 150 W\text{ W} ×\times 3.50 = 525 J\text{ J}_

    Correct

    t = 3.50 min\text{ min} ×\times 60 s/min\text{ s/min} = 210 s\text{ s}   ⟹  \implies E_{total\text{total}} = 150 J/s\text{ J/s} ×\times 210 s\text{ s} = 31,500 J\text{ J}_

    A watt is defined as one joule per second (1 W=1 J/s1\text{ W} = 1\text{ J/s}). To calculate energy in joules, the time must be converted from minutes to seconds (3.50 min×60=210 s3.50\text{ min} \times 60 = 210\text{ s}) before multiplying by power.

  2. Step 2

    q = 0.880 ×\times 525 J\text{ J} = 462 J\text{ J}

    Correct

    q = 0.880 ×\times 31,500 J\text{ J} = 27,720 J\text{ J} ≈\approx 2.77 ×\times 10^4 J\text{ J}

    You applied the 88.0%88.0\% efficiency correctly to your previous value, but the calculation inherits the missing time conversion factor of 60.

  3. Step 3

    Δ\Delta T = qm×c\frac{q}{m \times c} = 462 J400 g×0.897 J/(g⋅∘C)\frac{462\text{ J}}{400\text{ g} \times 0.897\text{ J}/(\text{g}\cdot^\circ\text{C})}   ⟹  \implies Δ\Delta T = 1.29^$\circC\text{C}

    Correct

    Δ\Delta T = 27 720 J400 g×0.897 J/(g⋅∘C)\frac{27\,720\text{ J}}{400\text{ g} \times 0.897\text{ J}/(\text{g}\cdot^\circ\text{C})} ≈\approx 77.3^$\circC\text{C}

    Your algebraic rearrangement and substitution into the heat capacity equation were entirely correct, but using q=462 Jq = 462\text{ J} made the final temperature change 60 times smaller than it should be.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified the relationship between power, time, and total energy (E=P⋅tE = P \cdot t).

You properly applied the 88.0%88.0\% efficiency factor to calculate thermal heat transfer (qq).

You correctly rearranged q=m⋅c⋅ΔTq = m \cdot c \cdot \Delta T to solve for the temperature change ΔT\Delta T.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Time unit conversion omitted in power equation

You substituted time directly as 3.50 rather than converting 3.50 minutes to 210 seconds.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Overlooking that power defined in watts (1 W=1 J/s1\text{ W} = 1\text{ J/s}) requires operating time to be in base SI units of seconds to yield energy in joules.

REASONING PATH
Your ACEpath teacher’s suggested approach
Check SI Base Units in Power Calculations
  • Because 1 W=1 J/s1\text{ W} = 1\text{ J/s}, multiplying power by time yields joules only when time is measured in seconds (t in seconds=t in minutes×60t\text{ in seconds} = t\text{ in minutes} \times 60).

  • Always write out unit labels explicitly during calculation: 150 J/s×(3.50 min×60 s/min)=31 500 J150\text{ J/s} \times (3.50\text{ min} \times 60\text{ s/min}) = 31\,500\text{ J}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert time to seconds: t=3.50 min×60 s/min=210 st = 3.50\text{ min} \times 60\text{ s/min} = 210\text{ s}.

  2. Compute total electrical energy: Etotal=150 W×210 s=31 500 JE_{\text{total}} = 150\text{ W} \times 210\text{ s} = 31\,500\text{ J}.

  3. Calculate absorbed thermal energy: q=0.880×31 500 J=27 720 J=2.77×104 Jq = 0.880 \times 31\,500\text{ J} = 27\,720\text{ J} = 2.77 \times 10^4\text{ J}.

  4. Calculate temperature change: ΔT=27 720 J400 g×0.897 J/(g⋅∘C)=27 720358.8∘C≈77.3∘C\Delta T = \frac{27\,720\text{ J}}{400\text{ g} \times 0.897\text{ J}/(\text{g}\cdot^\circ\text{C})} = \frac{27\,720}{358.8}^\circ\text{C} \approx 77.3^\circ\text{C}.

Final answer

q=2.77×104 Jq = 2.77 \times 10^4\text{ J} (27.7 kJ27.7\text{ kJ}), ΔT=77.3∘C\Delta T = 77.3^\circ\text{C}

NEXT STEPS
Final Takeaways from Your Teacher
  • Write unit fractions explicitly next to each quantity before multiplying, verifying that seconds cancel out.

  • Perform a sanity check on temperature change: heating a modest metal block with a 150 W150\text{ W} heater for several minutes should yield tens of degrees rather than 1.3∘C1.3^\circ\text{C}.

OverviewACEpath Teacher's Diagnosis

02 The student divides by the thermal efficiency instead of multiplying, erroneously thinking input energy is less than delivered heat.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    t=3.50×60 s=210 s  ⟹  Etotal=150 W×210 s=31500 Jt = 3.50 \times 60\text{ s} = 210\text{ s} \implies E_{\text{total}} = 150\text{ W} \times 210\text{ s} = 31500\text{ J}

  2. Step 2

    q=31500 J/0.880=35795 Jq = 31500\text{ J} / 0.880 = 35795\text{ J}

    Correct

    q=Etotal×0.880=31500 J×0.880=27720 J≈2.77×104 Jq = E_{\text{total}} \times 0.880 = 31500\text{ J} \times 0.880 = 27720\text{ J} \approx 2.77 \times 10^4\text{ J}

    You divided by the thermal efficiency instead of multiplying by it. Since efficiency represents the useful fraction of total energy delivered (η=qusefulEtotal\eta = \frac{q_{\text{useful}}}{E_{\text{total}}}), the delivered heat must be less than the total input energy: q=31500 J×0.880=27720 Jq = 31500\text{ J} \times 0.880 = 27720\text{ J}.

  3. Step 3

    ΔT=qm×c=35795 J400 g×0.897 J/(g⋅∘C)=99.8∘C\Delta T = \frac{q}{m \times c} = \frac{35795\text{ J}}{400\text{ g} \times 0.897\text{ J}/(\text{g}\cdot^\circ\text{C})} = 99.8^\circ\text{C}

    Correct

    ΔT=27720 J400 g×0.897 J/(g⋅∘C)≈77.3∘C\Delta T = \frac{27720\text{ J}}{400\text{ g} \times 0.897\text{ J}/(\text{g}\cdot^\circ\text{C})} \approx 77.3^\circ\text{C}

    Your rearrangement and algebraic evaluation of the heat equation were carried out properly, but the final temperature change was overestimated due to the incorrect value of qq carried over from the previous step.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted minutes to seconds to determine the operating duration.

You accurately calculated total electrical energy from power and time using E=P⋅tE = P \cdot t.

You correctly recalled and rearranged the specific heat formula q=m⋅c⋅ΔTq = m \cdot c \cdot \Delta T to solve for ΔT\Delta T.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted Efficiency Fraction

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You inverted the definition of efficiency, dividing by η\eta rather than multiplying, which incorrectly produced a delivered heat value greater than the total input energy.

REASONING PATH
Your ACEpath teacher’s suggested approach
Sanity Check on Energy and Efficiency
  • In any real process, useful output energy cannot exceed total input energy: Euseful≤EinputE_{\text{useful}} \le E_{\text{input}}.

  • Whenever you apply an efficiency fraction less than 11 (88.0%=0.88088.0\% = 0.880), verify that your output value is smaller than your input value.

Efficiency Definition
  • Efficiency is defined as η=useful outputtotal input\eta = \frac{\text{useful output}}{\text{total input}}, which rearranges to useful output=η×total input\text{useful output} = \eta \times \text{total input}.

  • Multiply the input electrical energy by 0.8800.880 to find the thermal energy delivered to the metal.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate the actual thermal energy absorbed: q=0.880×31500 J=27720 J=2.77×104 Jq = 0.880 \times 31500\text{ J} = 27720\text{ J} = 2.77 \times 10^4\text{ J}.

  2. Substitute the corrected qq into the rearranged heat equation: ΔT=27720 J400 g×0.897 J/(g⋅∘C)\Delta T = \frac{27720\text{ J}}{400\text{ g} \times 0.897\text{ J}/(\text{g}\cdot^\circ\text{C})}.

  3. Evaluate the numerical value: ΔT=27720358.8∘C≈77.3∘C\Delta T = \frac{27720}{358.8}^\circ\text{C} \approx 77.3^\circ\text{C}.

Final answer

q=2.77×104 Jq = 2.77 \times 10^4\text{ J} (27.7 kJ27.7\text{ kJ}), ΔT=77.3∘C\Delta T = 77.3^\circ\text{C}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the relationship between total input energy and delivered heat using η=EoutEin\eta = \frac{E_{\text{out}}}{E_{\text{in}}}.

  • Perform a quick magnitude check on every efficiency calculation to ensure output never exceeds input.

  • Complete the targeted flashcards and practice problems below to master efficiency conversions in calorimetry.

OverviewACEpath Teacher's Diagnosis

03 The student forgets to account for the 88.0% thermal efficiency, assuming 100% of the supplied electrical energy is transferred as heat.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    t=3.50×60 s=210 st = 3.50 \times 60\text{ s} = 210\text{ s}

  2. Step 2

    q=P×t=150 W×210 s=31500 Jq = P \times t = 150\text{ W} \times 210\text{ s} = 31500\text{ J}

    Correct

    q=η⋅P⋅t=0.880×150 W×210 s=27 720 J≈2.77×104 Jq = \eta \cdot P \cdot t = 0.880 \times 150\text{ W} \times 210\text{ s} = 27\,720\text{ J} \approx 2.77 \times 10^4\text{ J}

    This product gives the total electrical energy output (Etotal=31 500 JE_{\text{total}} = 31\,500\text{ J}), but the heating element is only 88.0%88.0\% efficient. You need to multiply by η=0.880\eta = 0.880 to find the actual thermal energy qq absorbed by the cylinder.

  3. Step 3

    ΔT=qm×c  ⟹  ΔT=31500 J400 g×0.897 J/(g⋅∘C)  ⟹  ΔT=31500358.8=87.8∘C\Delta T = \frac{q}{m \times c} \implies \Delta T = \frac{31500\text{ J}}{400\text{ g} \times 0.897\text{ J}/(\text{g}\cdot^\circ\text{C})} \implies \Delta T = \frac{31500}{358.8} = 87.8^\circ\text{C}

    Correct

    ΔT=qm⋅c=27 720 J400 g×0.897 J/(g⋅∘C)≈77.3∘C\Delta T = \frac{q}{m \cdot c} = \frac{27\,720\text{ J}}{400\text{ g} \times 0.897\text{ J}/(\text{g}\cdot^\circ\text{C})} \approx 77.3^\circ\text{C}

    Your formula rearrangement and substitution of mass and specific heat capacity were completely correct, but the calculated temperature change was affected by using 31 500 J31\,500\text{ J} instead of 27 720 J27\,720\text{ J}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted the operating time from minutes into seconds.

You correctly recalled and rearranged the heat equation to solve for temperature change ΔT=qm⋅c\Delta T = \frac{q}{m \cdot c}.

You accurately substituted the mass and specific heat values and carried out the arithmetic without calculation slips.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omitted Thermal Efficiency

You equated the total electrical energy produced by the heating element directly to the thermal energy absorbed by the metal, forgetting to scale by the 88.0%88.0\% efficiency.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing total energy input/output (Etotal=P⋅tE_{\text{total}} = P \cdot t) with useful thermal energy absorbed by the system (q=η⋅Etotalq = \eta \cdot E_{\text{total}}) when efficiency is less than 100%100\%.

REASONING PATH
Your ACEpath teacher’s suggested approach
Account for Inefficient Energy Transfer
  • Whenever an efficiency percentage η\eta is given for a heater or process, the actual heat absorbed is q=η×Etotalq = \eta \times E_{\text{total}}.

  • Scan the problem for efficiency ratings before setting q=P⋅tq = P \cdot t; convert the percentage to a decimal and apply it to find the usable heat.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate absorbed thermal energy: q=0.880×31 500 J=27 720 J=2.77×104 Jq = 0.880 \times 31\,500\text{ J} = 27\,720\text{ J} = 2.77 \times 10^4\text{ J}.

  2. Substitute the corrected heat into the rearranged specific heat equation: ΔT=27 720 J400 g×0.897 J/(g⋅∘C)\Delta T = \frac{27\,720\text{ J}}{400\text{ g} \times 0.897\text{ J}/(\text{g}\cdot^\circ\text{C})}.

  3. Evaluate the quotient: ΔT=27 720358.8≈77.26∘C≈77.3∘C\Delta T = \frac{27\,720}{358.8} \approx 77.26^\circ\text{C} \approx 77.3^\circ\text{C}.

Final answer

q=2.77×104 Jq = 2.77 \times 10^4\text{ J} (27.7 kJ27.7\text{ kJ}), ΔT=77.3∘C\Delta T = 77.3^\circ\text{C}

NEXT STEPS
Final Takeaways from Your Teacher
  • Write down the relationship q=η⋅P⋅tq = \eta \cdot P \cdot t explicitly as your first formula whenever electrical heaters with given efficiencies are involved.

  • Highlight efficiency percentages in problem prompts to remind yourself that not all electrical energy enters the thermal reservoir.

  • Practice paired calculations where you compare the theoretical maximum temperature rise (100%100\% efficiency) with the real temperature rise.

Lock it in

Similar question

01

A 250 W250\text{ W} immersion heater is placed into 500 g500\text{ g} of water (c=4.184 J/(g⋅∘C)c = 4.184\text{ J}/(\text{g}\cdot^\circ\text{C})) for 2.00 minutes2.00\text{ minutes}. Assuming 100%100\% thermal efficiency, calculate the total thermal energy transferred and the resulting temperature rise ΔT\Delta T.

Answer

q=3.00×104 Jq = 3.00 \times 10^4\text{ J} (30.0 kJ30.0\text{ kJ}), ΔT=14.3∘C\Delta T = 14.3^\circ\text{C}. Key steps: t=2.00 min×60=120 st = 2.00\text{ min} \times 60 = 120\text{ s}; q=250 W×120 s=30 000 Jq = 250\text{ W} \times 120\text{ s} = 30\,000\text{ J}; ΔT=30 000 J500 g×4.184 J/(g⋅∘C)≈14.3∘C\Delta T = \frac{30\,000\text{ J}}{500\text{ g} \times 4.184\text{ J}/(\text{g}\cdot^\circ\text{C})} \approx 14.3^\circ\text{C}.

02

An electric hot plate rated at 600 W600\text{ W} operates with 75.0%75.0\% efficiency to heat a 1.20 kg1.20\text{ kg} block of copper (c=0.385 J/(g⋅∘C)c = 0.385\text{ J}/(\text{g}\cdot^\circ\text{C})) from 20.0∘C20.0^\circ\text{C} to 85.0∘C85.0^\circ\text{C}. How many minutes must the hot plate run?

Answer

t=1.11 minutest = 1.11\text{ minutes} (66.7 seconds66.7\text{ seconds}). Key steps: ΔT=65.0∘C\Delta T = 65.0^\circ\text{C}; q=(1200 g)(0.385 J/(g⋅∘C))(65.0∘C)=30 030 Jq = (1200\text{ g})(0.385\text{ J}/(\text{g}\cdot^\circ\text{C}))(65.0^\circ\text{C}) = 30\,030\text{ J}; Etotal=30 030 J0.750=40 040 JE_{\text{total}} = \frac{30\,030\text{ J}}{0.750} = 40\,040\text{ J}; t=40 040 J600 W≈66.73 s=1.11 mint = \frac{40\,040\text{ J}}{600\text{ W}} \approx 66.73\text{ s} = 1.11\text{ min}.

03

A student attempts to heat an unknown metal sample (m=350 gm = 350\text{ g}) using a 180 W180\text{ W} cartridge heater operating for 4.00 minutes4.00\text{ minutes} at 90.0%90.0\% efficiency. The temperature of the metal rises by 42.5∘C42.5^\circ\text{C}. Calculate the specific heat capacity cc of the metal and state whether it would be underestimated or overestimated if time were entered as 4.004.00 instead of converted to seconds.

Answer

c=2.62 J/(g⋅∘C)c = 2.62\text{ J}/(\text{g}\cdot^\circ\text{C}); omitted conversion would underestimate cc by a factor of 60 (0.0436 J/(g⋅∘C)0.0436\text{ J}/(\text{g}\cdot^\circ\text{C})). Key steps: t=240 st = 240\text{ s}; E=180 W×240 s=43 200 JE = 180\text{ W} \times 240\text{ s} = 43\,200\text{ J}; q=0.900×43 200=38 880 Jq = 0.900 \times 43\,200 = 38\,880\text{ J}; c=38 880 J(350 g)(42.5∘C)≈2.62 J/(g⋅∘C)c = \frac{38\,880\text{ J}}{(350\text{ g})(42.5^\circ\text{C})} \approx 2.62\text{ J}/(\text{g}\cdot^\circ\text{C}).

Loading workspace…