Resources

A metallurgical technician subjects three metallic rods of identical initial length L0=100.0 mmL_0 = 100.0\text{ mm} and cross-sectional area A0=25.0 mm2A_0 = 25.0\text{ mm}^2 to tensile deformation until fracture: Specimen A (annealed copper), Specimen B (cast iron), and Specimen C (mild steel). Specimen A stretches to a final fracture length of Lf=145.0 mmL_f = 145.0\text{ mm} with a final neck cross-sectional area of Af=11.25 mm2A_f = 11.25\text{ mm}^2. (a) Determine the ductility of Specimen A expressed as both percent elongation (%EL\text{\%EL}) and percent reduction in area (%RA\text{\%RA}). (b) Rank the three specimens from greatest to least ductility.

Answer and steps

Final answer

(a) %EL=45.0%\text{\%EL} = 45.0\%, %RA=55.0%\text{\%RA} = 55.0\%; (b) Specimen A (annealed copper) >> Specimen C (mild steel) >> Specimen B (cast iron).

Steps

Part (a): Calculating Percent Elongation and Percent Reduction in Area

Ductility is a measure of a material's ability to undergo significant plastic deformation before rupture. In tensile testing, it is quantitatively evaluated using two parameters: percent elongation (%EL\text{\%EL}) and percent reduction in area (%RA\text{\%RA}).

  1. Calculate Percent Elongation (%EL\text{\%EL}): The elongation reflects the permanent plastic stretch along the gauge length relative to its original length: %EL=Lf−L0L0×100%\text{\%EL} = \frac{L_f - L_0}{L_0} \times 100\%

    Substitute the given values for Specimen A (L0=100.0 mmL_0 = 100.0\text{ mm}, Lf=145.0 mmL_f = 145.0\text{ mm}): %EL=145.0 mm−100.0 mm100.0 mm×100%=45.0 mm100.0 mm×100%=45.0%\text{\%EL} = \frac{145.0\text{ mm} - 100.0\text{ mm}}{100.0\text{ mm}} \times 100\% = \frac{45.0\text{ mm}}{100.0\text{ mm}} \times 100\% = 45.0\%

  2. Calculate Percent Reduction in Area (%RA\text{\%RA}): The reduction in area measures the localized necking at the fracture point relative to the original cross-sectional area: %RA=A0−AfA0×100%\text{\%RA} = \frac{A_0 - A_f}{A_0} \times 100\%

    Substitute the given values for Specimen A (A0=25.0 mm2A_0 = 25.0\text{ mm}^2, Af=11.25 mm2A_f = 11.25\text{ mm}^2): %RA=25.0 mm2−11.25 mm225.0 mm2×100%=13.75 mm225.0 mm2×100%=55.0%\text{\%RA} = \frac{25.0\text{ mm}^2 - 11.25\text{ mm}^2}{25.0\text{ mm}^2} \times 100\% = \frac{13.75\text{ mm}^2}{25.0\text{ mm}^2} \times 100\% = 55.0\%

Common Pitfall: Be careful not to swap A0A_0 and AfA_f or divide by the final dimension instead of the initial dimension; ductility formulas are always normalized to the un-deformed initial values (L0L_0 and A0A_0).


Part (b): Ranking the Ductility of the Three Specimens

Ductility at the atomic and microstructural level is governed by metallic bonding and crystal slip:

  • Specimen A (Annealed copper): Pure copper has a face-centered cubic (FCC\text{FCC}) crystal structure with 1212 primary slip systems. Annealing relieves internal dislocations, allowing planes of copper cations to easily slide past each other through the non-directional "sea of electrons" without breaking metallic bonds. It shows exceptionally high ductility (%EL≈45%\text{\%EL} \approx 45\%).
  • Specimen C (Mild steel): Mild steel is a low-carbon alloy dominated by body-centered cubic (BCC\text{BCC}) ferrite with a small fraction of pearlite. While highly ductile compared to hard alloys (%EL≈20–30%\text{\%EL} \approx 20\text{--}30\%), interstitial carbon atoms create lattice strain and pin dislocations, making it less ductile than pure annealed copper.
  • Specimen B (Cast iron): Cast iron contains a high carbon content (>2 wt%>2\text{ wt\%}) forming brittle phases such as cementite (FeX3C\ce{Fe3C}) and graphite flakes. These inclusions act as internal stress concentrators that initiate microcracks with negligible plastic strain before fracture (%EL<5%\text{\%EL} < 5\%), making cast iron brittle.

Therefore, the ranking from greatest to least ductility is: Specimen A (annealed copper)>Specimen C (mild steel)>Specimen B (cast iron)\text{Specimen A (annealed copper)} > \text{Specimen C (mild steel)} > \text{Specimen B (cast iron)}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student divides by the final dimensions instead of the initial dimensions when calculating percent elongation and reduction in area, yielding incorrect ductility values.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    %EL=(145.0−100.0145.0)×100%=31.0%\text{\%EL} = \left(\frac{145.0 - 100.0}{145.0}\right) \times 100\% = 31.0\%

    Correct

    %EL=Lf−L0L0×100%=145.0 mm−100.0 mm100.0 mm×100%=45.0%\text{\%EL} = \frac{L_f - L_0}{L_0} \times 100\% = \frac{145.0\text{ mm} - 100.0\text{ mm}}{100.0\text{ mm}} \times 100\% = 45.0\%

    You normalized the change in length by dividing by the final length Lf=145.0 mmL_f = 145.0\text{ mm} rather than the original gauge length L0=100.0 mmL_0 = 100.0\text{ mm}.

  2. Step 2

    %RA=(25.0−11.2511.25)×100%=122.2%\text{\%RA} = \left(\frac{25.0 - 11.25}{11.25}\right) \times 100\% = 122.2\%

    Correct

    %RA=A0−AfA0×100%=25.0 mm2−11.25 mm225.0 mm2×100%=55.0%\text{\%RA} = \frac{A_0 - A_f}{A_0} \times 100\% = \frac{25.0\text{ mm}^2 - 11.25\text{ mm}^2}{25.0\text{ mm}^2} \times 100\% = 55.0\%

    You divided the change in cross-sectional area by the necked final area Af=11.25 mm2A_f = 11.25\text{ mm}^2 instead of the original area A0=25.0 mm2A_0 = 25.0\text{ mm}^2, producing an impossible reduction greater than 100%100\%.

  3. Step 3

    Specimen A>Specimen C>Specimen B\text{Specimen A} > \text{Specimen C} > \text{Specimen B}

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly computed the dimensional changes ΔL=45.0 mm\Delta L = 45.0\text{ mm} and ΔA=13.75 mm2\Delta A = 13.75\text{ mm}^2.

You accurately ranked the three specimens by comparing the ductility of FCC copper, BCC mild steel, and brittle cast iron.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Incorrect Normalization Base in Ductility Formulas

Dividing by the final dimensions (LfL_f and AfA_f) instead of the undeformed initial dimensions (L0L_0 and A0A_0).

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated percentage change as a ratio relative to the final state rather than referencing it to the undeformed baseline material.

REASONING PATH
Your ACEpath teacher’s suggested approach
Baseline Reference Check
  • Engineering ductility parameters measure deformation relative to the undeformed specimen (L0L_0 and A0A_0).

  • Always place the initial dimension in the denominator: %EL=Lf−L0L0×100%\text{\%EL} = \frac{L_f - L_0}{L_0} \times 100\% and %RA=A0−AfA0×100%\text{\%RA} = \frac{A_0 - A_f}{A_0} \times 100\%.

Physical Reality Check for Area Reduction
  • A tensile specimen can lose at most 100%100\% of its original cross-sectional area if it necks to a sharp point (Af=0A_f = 0).

  • If your calculated %RA\text{\%RA} exceeds 100%100\%, check immediately whether you accidentally placed AfA_f in the denominator.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. %EL=145.0 mm−100.0 mm100.0 mm×100%=45.0 mm100.0 mm×100%=45.0%\text{\%EL} = \frac{145.0\text{ mm} - 100.0\text{ mm}}{100.0\text{ mm}} \times 100\% = \frac{45.0\text{ mm}}{100.0\text{ mm}} \times 100\% = 45.0\%

  2. %RA=25.0 mm2−11.25 mm225.0 mm2×100%=13.75 mm225.0 mm2×100%=55.0%\text{\%RA} = \frac{25.0\text{ mm}^2 - 11.25\text{ mm}^2}{25.0\text{ mm}^2} \times 100\% = \frac{13.75\text{ mm}^2}{25.0\text{ mm}^2} \times 100\% = 55.0\%

  3. Retain your correct ranking: Specimen A>Specimen C>Specimen B\text{Specimen A} > \text{Specimen C} > \text{Specimen B}.

Final answer

(a) %EL=45.0%\text{\%EL} = 45.0\%, %RA=55.0%\text{\%RA} = 55.0\%; (b) Specimen A (annealed copper) >> Specimen C (mild steel) >> Specimen B (cast iron)

NEXT STEPS
Final Takeaways from Your Teacher
  • Memorize that both engineering strain and ductility metrics are always normalized by the original gauge dimensions (L0L_0, A0A_0).

  • Use the 100%100\% boundary sanity check: a reduction in cross-sectional area cannot exceed 100%100\%.

  • Practice calculating engineering strain versus true strain to solidify your understanding of baseline dimensions.

OverviewACEpath Teacher's Diagnosis

02 The student confuses the definition of percent reduction in area with the remaining fraction of area, calculating (Af / A0) * 100% rather than ((A0 - Af) / A0) * 100%.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    %EL=145.0−100.0100.0×100%  ⟹  %EL=45.0%\text{\%EL} = \frac{145.0 - 100.0}{100.0} \times 100\% \implies \text{\%EL} = 45.0\%

  2. Step 2

    %RA=(11.2525.0)×100%  ⟹  %RA=45.0%\text{\%RA} = \left(\frac{11.25}{25.0}\right) \times 100\% \implies \text{\%RA} = 45.0\%

    Correct

    %RA=A0−AfA0×100%=25.0 mm2−11.25 mm225.0 mm2×100%=55.0%\text{\%RA} = \frac{A_0 - A_f}{A_0} \times 100\% = \frac{25.0\text{ mm}^2 - 11.25\text{ mm}^2}{25.0\text{ mm}^2} \times 100\% = 55.0\%

    You calculated the final area as a fraction of the initial area (AfA0×100%\frac{A_f}{A_0} \times 100\%) instead of the fractional reduction in area (A0−AfA0×100%\frac{A_0 - A_f}{A_0} \times 100\%).

  3. Step 3

    Specimen A>Specimen C>Specimen B\text{Specimen A} > \text{Specimen C} > \text{Specimen B}

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly recalled and computed the percent elongation (%EL\text{\%EL}).

You demonstrated a solid qualitative understanding of metallic ductility across annealed copper, mild steel, and cast iron.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Formula Definition Confusion: Remaining Ratio vs. Relative Reduction

You set up %RA\text{\%RA} as AfA0×100%\frac{A_f}{A_0} \times 100\% rather than measuring the change A0−AfA0×100%\frac{A_0 - A_f}{A_0} \times 100\%.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated percent reduction in area as the surviving area percentage rather than the lost or reduced cross-sectional area relative to the original area.

REASONING PATH
Your ACEpath teacher’s suggested approach
Define Reduction as a Change
  • Reduction always denotes the decrease in value: ΔAloss=A0−Af\Delta A_{\text{loss}} = A_0 - A_f.

  • Always subtract the final necked area from the original area before dividing by the original area: %RA=A0−AfA0×100%\text{\%RA} = \frac{A_0 - A_f}{A_0} \times 100\%.

Complementarity Check
  • The remaining area percentage and the percent reduction in area sum to 100%100\%.

  • If your calculated remaining area fraction is 45.0%45.0\%, verify that the reduction itself is 100%−45.0%=55.0%100\% - 45.0\% = 55.0\%.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Identify the original area A0=25.0 mm2A_0 = 25.0\text{ mm}^2 and final neck area Af=11.25 mm2A_f = 11.25\text{ mm}^2.

  2. Compute the area lost during necking: ΔA=A0−Af=25.0 mm2−11.25 mm2=13.75 mm2\Delta A = A_0 - A_f = 25.0\text{ mm}^2 - 11.25\text{ mm}^2 = 13.75\text{ mm}^2.

  3. Normalize by the initial area and convert to percentage: %RA=13.75 mm225.0 mm2×100%=55.0%\text{\%RA} = \frac{13.75\text{ mm}^2}{25.0\text{ mm}^2} \times 100\% = 55.0\%.

Final answer

(a) %EL=45.0%\text{\%EL} = 45.0\%, %RA=55.0%\text{\%RA} = 55.0\%; (b) Specimen A >> Specimen C >> Specimen B

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the formal definitions of ductility parameters (elongation versus area reduction) to ensure you always use the change in dimensions.

  • Practice with tensile test data where diameter is provided, being careful to compute areas or apply the squared diameter ratio (d02−df2d02)×100%(\frac{d_0^2 - d_f^2}{d_0^2}) \times 100\%.

OverviewACEpath Teacher's Diagnosis

03 The student confuses ductility with strength or hardness, ranking brittle cast iron ahead of mild steel or copper.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    %EL=145.0−100.0100.0×100%=45.0%\text{\%EL} = \frac{145.0 - 100.0}{100.0} \times 100\% = 45.0\%

  2. Step 2

    %RA=25.0−11.2525.0×100%=55.0%\text{\%RA} = \frac{25.0 - 11.25}{25.0} \times 100\% = 55.0\%

  3. Step 3

    Cast iron is the hardest metal, so it has the highest ductility.\text{Cast iron is the hardest metal, so it has the highest ductility.}   ⟹  \implies Specimen B\text{Specimen B} > Specimen C\text{Specimen C} > Specimen A\text{Specimen A}

    Correct

    Specimen A (annealed copper)\text{Specimen A (annealed copper)} > Specimen C (mild steel)\text{Specimen C (mild steel)} > Specimen B (cast iron)\text{Specimen B (cast iron)}

    Ductility measures the capacity for permanent plastic deformation before fracture, not resistance to indentation or scratching (hardness). Cast iron has high carbon content forming brittle carbide and graphite phases, making it brittle with minimal plastic deformation. Pure annealed copper deforms substantially before fracture via dislocation slip in its FCC lattice, making it the most ductile.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used the initial length as the reference denominator to compute percent elongation.

You calculated the area reduction and percent reduction in area accurately.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Conceptual confusion between ductility and hardness

You equated high hardness with high ductility.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated mechanical hardness and ductility as directly correlated properties rather than recognizing that high hardness/brittleness typically opposes plastic deformability (ductility).

REASONING PATH
Your ACEpath teacher’s suggested approach
Ductility vs. Hardness
  • Ductility is the degree of plastic deformation a material can sustain before fracture (quantified by %EL\text{\%EL} and %RA\text{\%RA}); hardness is resistance to localized plastic surface deformation.

  • Associate ductility with stretching into wires or necking, and brittleness/hardness with fracture under low tensile strain.

Microstructure and Bonding Influence
  • FCC pure metals (like annealed copper) possess numerous slip systems and deform readily. High-carbon alloys (like cast iron) contain brittle phases that pin dislocations and initiate early cracks.

  • Rank materials from pure FCC metals (highest ductility) to low-carbon steels (moderate ductility) to high-carbon cast irons (lowest ductility/brittle).

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Recall that ductility represents how much a material stretches and necks down before snapping: higher plastic strain means higher ductility.

  2. Evaluate the materials microstructurally: Annealed copper (Specimen A) is an FCC metal with extensive slip and no hard inclusions, giving the highest ductility (%EL≈45%\%EL \approx 45\%). Mild steel (Specimen C) is a low-carbon BCC alloy with moderate ductility (%EL≈20–30%\%EL \approx 20\text{--}30\%). Cast iron (Specimen B) contains large amounts of carbon and graphite flakes that cause brittle fracture with almost no plastic deformation (%EL<5%\%EL < 5\%).

  3. Order the specimens from greatest to least ductility: Specimen A > Specimen C > Specimen B.

Final answer

(a) %EL=45.0%\text{\%EL} = 45.0\%, %RA=55.0%\text{\%RA} = 55.0\%; (b) Specimen A (annealed copper) >> Specimen C (mild steel) >> Specimen B (cast iron)

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the metallurgical definitions distinguishing ductility, brittleness, hardness, and tensile strength.

  • Practice comparing stress-strain curves to identify which curve displays the greatest plastic elongation before failure.

Lock it in

Similar question

01

An aluminum alloy specimen with an initial gauge length of L0=50.0 mmL_0 = 50.0\text{ mm} and initial diameter d0=10.0 mmd_0 = 10.0\text{ mm} undergoes tensile fracture. The final gauge length is Lf=62.0 mmL_f = 62.0\text{ mm} and the neck diameter at fracture is df=8.0 mmd_f = 8.0\text{ mm}. Calculate the percent elongation (%EL) and percent reduction in area (%RA).

Answer

%EL=24.0%\text{\%EL} = 24.0\%, %RA=36.0%\text{\%RA} = 36.0\%. Steps: %EL=62.0−50.050.0×100%=24.0%\text{\%EL} = \frac{62.0 - 50.0}{50.0} \times 100\% = 24.0\%. Cross-sectional areas are proportional to d2d^2, so %RA=d02−df2d02×100%=100.0−64.0100.0×100%=36.0%\text{\%RA} = \frac{d_0^2 - d_f^2}{d_0^2} \times 100\% = \frac{100.0 - 64.0}{100.0} \times 100\% = 36.0\%.

02

A cylindrical titanium tensile rod with initial diameter 12.0 mm12.0\text{ mm} exhibits a percent reduction in area of %RA=43.75%\text{\%RA} = 43.75\% at fracture. Determine the cross-sectional area at the fracture neck, AfA_f.

Answer

Af=63.6 mm2A_f = 63.6\text{ mm}^2. Steps: Initial area A0=π4(12.0 mm)2≈113.1 mm2A_0 = \frac{\pi}{4}(12.0\text{ mm})^2 \approx 113.1\text{ mm}^2. From %RA=A0−AfA0×100%\text{\%RA} = \frac{A_0 - A_f}{A_0} \times 100\%, we have Af=A0(1−0.4375)=113.1×0.5625≈63.6 mm2A_f = A_0(1 - 0.4375) = 113.1 \times 0.5625 \approx 63.6\text{ mm}^2.

03

Two metallic alloys, X and Y, have identical initial dimensions (L0=80.0 mmL_0 = 80.0\text{ mm}, A0=40.0 mm2A_0 = 40.0\text{ mm}^2). At tensile fracture, Alloy X has Lf=112.0 mmL_f = 112.0\text{ mm} and Af=26.0 mm2A_f = 26.0\text{ mm}^2, while Alloy Y has Lf=96.0 mmL_f = 96.0\text{ mm} and Af=12.0 mm2A_f = 12.0\text{ mm}^2. (a) Calculate %EL and %RA for both alloys. (b) Explain why an alloy can have a higher %RA but a lower %EL.

Answer

(a) Alloy X: %EL=40.0%\text{\%EL} = 40.0\%, %RA=35.0%\text{\%RA} = 35.0\%; Alloy Y: %EL=20.0%\text{\%EL} = 20.0\%, %RA=70.0%\text{\%RA} = 70.0\%. (b) %EL\text{\%EL} measures uniform plastic stretch distributed along the entire gauge length, whereas %RA\text{\%RA} captures intense localized plastic flow (necking) at the point of fracture.

Loading workspace…