Resources
A suspension of fine hydrophobic polymer microparticles (density , mean particle diameter ) in water is left in a cylindrical settling column of height at (water viscosity , density , ). As time , all suspended particles settle out under gravity governed by Stokes' terminal settling velocity . (a) Calculate the terminal settling velocity of a particle in . (b) Determine the time required for a particle starting at the top meniscus to reach the bottom, marking the transition from an unstable heterogeneous suspension to a separated two-phase system composed of a settled sediment phase beneath an optically clear liquid supernatant.
Answer and steps
Final answer
(a) ; (b) (approximately )
Steps
Convert Given Quantities to SI Units
Understanding the Mixture Type
A suspension is a heterogeneous mixture containing solid particles that are sufficiently large that they do not remain permanently dispersed. Unlike a homogeneous mixture (such as a true solution) where solute particles never settle, the dispersed phase in an unstable suspension eventually separates under gravity into a clear liquid supernatant and a settled sediment phase.
To use Stokes' law accurately, all quantities must be in standard SI units:
- Particle radius ():
- Particle density ():
- Fluid density ():
- Density difference ():
- Dynamic viscosity ():
- Settling height ():
- Acceleration due to gravity ():
Calculate the Terminal Settling Velocity
Substitute the SI values into Stokes' settling formula:
Common Pitfall: Using particle diameter () instead of particle radius (), or failing to convert to (), will lead to an incorrect velocity by several orders of magnitude.
Determine the Total Settling Time
A particle starting at the top liquid meniscus must travel the entire column height at constant settling velocity :
Converting this duration into days:
After approximately , all particles have settled to the bottom, completing the physical separation of this heterogeneous mixture into distinct phases.
Typical errors
01 The student uses the particle diameter directly instead of the radius in Stokes' settling formula, overestimating the velocity by a factor of 4 and underestimating settling time.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You correctly found the density difference in SI units, but you assigned the given mean diameter directly to the radius instead of dividing by .
- Step 2Correct
Your algebraic substitution and arithmetic were carried out properly, but because was doubled, overstated the velocity by a factor of .
- Step 3Correct
You correctly applied with the column height converted to meters, but the result was propagated from the inaccurate terminal velocity.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly converted density from to SI units of .
You accurately calculated the density difference .
You correctly converted the settling height from to .
You set up and evaluated Stokes' settling law and the constant-velocity time equation with sound arithmetic.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou treated the diameter as the radius .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConflating particle diameter () with particle radius () in formulas that explicitly require radius, overlooking that Stokes' settling velocity scales with .
REASONING PATH
Your ACEpath teacher’s suggested approach- Radius vs. Diameter Check
In Stokes' law , the symbol always represents radius, which is half of the diameter ().
Whenever a problem provides 'diameter', immediately write as your very first recorded step.
- Quadratic Scaling Awareness
Because velocity depends on , doubling the input dimension scales the settling velocity by and reduces settling time to of its true value.
Sanity-check whether an unexpected factor of could stem from an unhalved diameter.
CORRECTED PATH
ACEpath Teacher's Demonstration(a) ; (b) (approximately )
02 The student fails to convert the densities from g/cm³ to kg/m³, underestimating the density difference and resulting velocity by a factor of 1000.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You subtracted the densities directly in . To remain consistent with viscosity in and gravity in , density must be converted to using .
- Step 3Correct
You substituted your values into Stokes' settling formula and carried out the arithmetic correctly, but the result was underestimated by because was entered as instead of .
- Step 4Correct
Your relationship and height conversion are correct, but propagating your underestimated velocity yielded an overstated settling time.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly converted the particle diameter to the radius in meters.
You selected and set up the correct equation for Stokes' settling velocity.
You correctly applied the relationship to compute settling time from the column height.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated densities given in CGS units () as if they were already in SI base units (), missing the conversion factor of needed when pairing with and .
REASONING PATH
Your ACEpath teacher’s suggested approach- SI Density Conversion
Always multiply densities in by before plugging them into formulas involving Pascals, meters, and seconds.
- Plausibility Check on Timescale
Compare your calculated time () to physical reality: micron-sized particles with in water settle in weeks, not decades.
CORRECTED PATH
ACEpath Teacher's DemonstrationConvert the density difference: .
Re-evaluate Stokes' terminal settling velocity: .
Compute total settling time: (or ).
(a) ; (b) (approximately )
03 The student forgets to convert the column height from centimeters to meters when calculating the settling time, obtaining a value that is 100 times too large.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
⟹ ⟹
- Step 2
⟹ ⟹
Correct⟹
You used directly in centimeters without converting it to standard SI units (meters). Because velocity is expressed in , the settling distance must be , yielding .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly halved the diameter to find the particle radius in meters.
You converted the densities from to and computed the buoyant density difference accurately.
You correctly applied Stokes' settling formula to compute .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou substituted the height value directly into the settling time formula without attaching or converting its unit from centimeters to meters.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisFailing to enforce SI unit consistency across kinematic equations after completing dynamic formula calculations.
REASONING PATH
Your ACEpath teacher’s suggested approach- Unit Alignment Check
All lengths in kinematic equations must match the distance base unit of velocity (meters for ).
Always explicitly write out the unit on every measured parameter () before substituting into formulas.
CORRECTED PATH
ACEpath Teacher's DemonstrationConvert the settling height from centimeters to meters: .
Calculate the settling time: .
(a) ; (b) (or )
Lock it in
In Stokes' settling law, , what does the symbol stand for?
is the particle radius (). If given diameter , you must divide by before squaring.
Similar question
A mineral dust particle with diameter and density settles in water (density , viscosity , ). Calculate its radius in meters and its terminal settling velocity in .
Answer
. Using , .
Two identical settling columns contain suspensions of polymer beads with the same density difference. Column A contains beads of mean diameter , while Column B contains beads of mean diameter . Determine the ratio of their settling velocities, , and the ratio of times required to settle the same column height, .
Answer
Since , . Settling time is inversely proportional to velocity (), so .
A suspension of quartz silt particles (density , mean diameter ) settles through a column of water at (, , ). (a) Find the settling velocity . (b) Determine the time in minutes for complete phase separation.
Answer
(a) , . . (b) .