Resources

The Clapeyron equation governing phase equilibrium boundaries is given by dPdT=ΔSΔV=ΔHTΔV\frac{dP}{dT} = \frac{\Delta S}{\Delta V} = \frac{\Delta H}{T \Delta V}. In the phase diagram of water, ice Ih melts into liquid water with an increase in density (ρice=0.9167 g/cm3\rho_{\text{ice}} = 0.9167\text{ g/cm}^3 and ρliquid=0.9998 g/cm3\rho_{\text{liquid}} = 0.9998\text{ g/cm}^3 at 0.0∘C0.0^\circ\text{C}). For dry ice (solid CO2\text{CO}_2), the solid density is ρsolid=1.56 g/cm3\rho_{\text{solid}} = 1.56\text{ g/cm}^3 and the liquid density at −56.6∘C-56.6^\circ\text{C} is ρliquid=1.18 g/cm3\rho_{\text{liquid}} = 1.18\text{ g/cm}^3. (a) Determine the algebraic sign (positive or negative) of the slope dPdT\frac{dP}{dT} of the solid-liquid coexistence line for H2O\text{H}_2\text{O} and for CO2\text{CO}_2. (b) Based on these sign conventions, state whether increasing the pressure on a solid sample at a temperature just below its normal melting point causes melting or prevents melting for each substance.

Answer and steps

Final answer

(a) dPdT\frac{dP}{dT} is negative (−-) for H2O\text{H}_2\text{O} and positive (++) for CO2\text{CO}_2; (b) For H2O\text{H}_2\text{O}, increasing pressure causes melting; for CO2\text{CO}_2, increasing pressure prevents melting (favors the solid phase).

Steps

Part (a): Determining the Sign of dPdT\frac{dP}{dT}

The Clapeyron equation for a solid-to-liquid phase transition (melting or fusion) is:

dPdT=ΔHfusTΔVfus\frac{dP}{dT} = \frac{\Delta H_{\text{fus}}}{T \Delta V_{\text{fus}}}

  1. Sign of ΔHfus\Delta H_{\text{fus}} and TT: Melting is an endothermic process for any pure substance, which means heat is absorbed: ΔHfus>0\Delta H_{\text{fus}} > 0 Absolute temperature TT in Kelvin is always positive (T>0T > 0). Therefore, the sign of the slope dPdT\frac{dP}{dT} is completely determined by the sign of the volume change upon melting: ΔVfus=Vliquid−Vsolid\Delta V_{\text{fus}} = V_{\text{liquid}} - V_{\text{solid}}
  2. Volume change from density: Specific volume is inversely proportional to density (V=1ρV = \frac{1}{\rho}): ΔVfus=1ρliquid−1ρsolid\Delta V_{\text{fus}} = \frac{1}{\rho_{\text{liquid}}} - \frac{1}{\rho_{\text{solid}}}

    • For HX2O\ce{H2O}: ρice=0.9167 g/cm3<ρliquid=0.9998 g/cm3\rho_{\text{ice}} = 0.9167\text{ g/cm}^3 < \rho_{\text{liquid}} = 0.9998\text{ g/cm}^3 Since the liquid is denser than the solid, it occupies a smaller volume: Vliquid<Vsolid  ⟹  ΔVfus<0V_{\text{liquid}} < V_{\text{solid}} \implies \Delta V_{\text{fus}} < 0 Substituting this into the Clapeyron equation gives: dPdT=(+)(+)(−)<0(negative)\frac{dP}{dT} = \frac{(+)}{(+)(-)} < 0 \quad (\text{negative})
    • For COX2\ce{CO2}: ρsolid=1.56 g/cm3>ρliquid=1.18 g/cm3\rho_{\text{solid}} = 1.56\text{ g/cm}^3 > \rho_{\text{liquid}} = 1.18\text{ g/cm}^3 Since the solid is denser than the liquid, the volume expands upon melting: Vliquid>Vsolid  ⟹  ΔVfus>0V_{\text{liquid}} > V_{\text{solid}} \implies \Delta V_{\text{fus}} > 0 Substituting this into the Clapeyron equation gives: dPdT=(+)(+)(+)>0(positive)\frac{dP}{dT} = \frac{(+)}{(+)(+)} > 0 \quad (\text{positive})

Part (b): Effect of Increasing Pressure Just Below the Melting Point

By Le Chatelier's principle, applying pressure to a system in equilibrium shifts it toward the phase with the higher density (smaller molar volume). Graphically, increasing pressure corresponds to moving vertically upward on a pressure-temperature (P-TP\text{-}T) phase diagram:

  • For HX2O\ce{H2O}: Because dPdT<0\frac{dP}{dT} < 0, the solid-liquid coexistence line tilts backward (to the left). A solid point just below the normal melting point lies directly underneath the liquid region. Increasing pressure at this temperature moves the state point vertically upward across the boundary into the liquid region. Thus, increasing pressure causes melting.
  • For COX2\ce{CO2}: Because dPdT>0\frac{dP}{dT} > 0, the solid-liquid coexistence line tilts forward (to the right), which is standard for most substances. Solid COX2\ce{CO2} is denser than liquid COX2\ce{CO2}. Applying pressure stabilizes the denser solid phase, moving the state point further into the solid domain and shifting the melting temperature to a higher value. Thus, increasing pressure prevents melting (favors the solid phase).

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student calculates ΔV as V_initial - V_final (solid - liquid) instead of V_final - V_initial, inverting the sign of ΔV and therefore inverting the slope dP/dT for both substances.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    ΔHfusion>0\Delta H_{\text{fusion}} > 0

  2. Step 2

    ΔV=Vsolid−Vliquid\Delta V = V_{\text{solid}} - V_{\text{liquid}}

    Correct

    ΔVfus=Vliquid−Vsolid\Delta V_{\text{fus}} = V_{\text{liquid}} - V_{\text{solid}}

    For any physical transition, change is defined as final state minus initial state. Because melting goes from solid to liquid, the change in volume is ΔV=Vliquid−Vsolid\Delta V = V_{\text{liquid}} - V_{\text{solid}}.

  3. Step 3

    For HX2O\ce{H2O}, ρice<ρliquid  ⟹  Vsolid>Vliquid\rho_{\text{ice}} < \rho_{\text{liquid}} \implies V_{\text{solid}} > V_{\text{liquid}} and ΔV>0  ⟹  dPdT>0 (positive)  ⟹  For COX2,ρsolid>ρliquid  ⟹  Vsolid<Vliquid\Delta V > 0 \implies \frac{dP}{dT} > 0 \text{ (positive)} \implies \text{For } \ce{CO2}, \rho_{\text{solid}} > \rho_{\text{liquid}} \implies V_{\text{solid}} < V_{\text{liquid}} and ΔV<0  ⟹  dPdT<0 (negative)\Delta V < 0 \implies \frac{dP}{dT} < 0 \text{ (negative)}

    Correct

    For HX2O\ce{H2O}: Vliquid<Vsolid  ⟹  ΔVfus<0  ⟹  dPdT<0 (negative)  ⟹  For COX2:Vliquid>Vsolid  ⟹  ΔVfus>0  ⟹  dPdT>0 (positive)V_{\text{liquid}} < V_{\text{solid}} \implies \Delta V_{\text{fus}} < 0 \implies \frac{dP}{dT} < 0 \text{ (negative)} \implies \text{For } \ce{CO2}: V_{\text{liquid}} > V_{\text{solid}} \implies \Delta V_{\text{fus}} > 0 \implies \frac{dP}{dT} > 0 \text{ (positive)}

    Your reasoning about the relative specific volumes from densities was solid, but substituting your inverted formula for ΔV\Delta V flipped the sign of dPdT\frac{dP}{dT} for both substances.

  4. Step 4

    For HX2O\ce{H2O}, dPdT>0\frac{dP}{dT} > 0 so increasing pressure raises melting point and prevents melting.   ⟹  \implies For COX2\ce{CO2}, dPdT<0\frac{dP}{dT} < 0 so increasing pressure lowers melting point and causes melting.

    Correct

    For HX2O\ce{H2O}: dPdT<0\frac{dP}{dT} < 0, so increasing pressure lowers the melting point and causes melting.   ⟹  \implies For COX2\ce{CO2}: dPdT>0\frac{dP}{dT} > 0, so increasing pressure raises the melting point and prevents melting.

    You correctly related the sign of dPdT\frac{dP}{dT} to the shift in melting point, but because the signs were inverted in the previous step, your conclusions for both substances were reversed.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly established that melting is an endothermic process with ΔH>0\Delta H > 0.

You correctly used the inverse relationship between density and specific volume to compare solid and liquid phases.

You followed a clear, logical chain of thermodynamic reasoning from the Clapeyron equation to phase behavior.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted State Difference

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You reversed the order of subtraction when defining ΔV\Delta V, writing initial minus final instead of final minus initial.

REASONING PATH
Your ACEpath teacher’s suggested approach
State Function Difference Convention
  • For any process going from state A to state B, ΔX=Xfinal−Xinitial=XB−XA\Delta X = X_{\text{final}} - X_{\text{initial}} = X_B - X_A.

  • Always write out ΔVfus=Vliquid−Vsolid\Delta V_{\text{fus}} = V_{\text{liquid}} - V_{\text{solid}} before substituting values or signs.

Le Chatelier Check for Pressure
  • Increasing pressure always favors the phase with higher density (smaller volume).

  • Check your final result physically: liquid water is denser than ice, so higher pressure must favor the liquid (causing melting).

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Define the volume change of fusion correctly: ΔVfus=Vliquid−Vsolid\Delta V_{\text{fus}} = V_{\text{liquid}} - V_{\text{solid}}.

  2. For HX2O\ce{H2O}, liquid water is denser than ice, so Vliquid<VsolidV_{\text{liquid}} < V_{\text{solid}}, giving ΔVfus<0\Delta V_{\text{fus}} < 0. With ΔH>0\Delta H > 0 and T>0T > 0, dPdT=ΔHTΔV<0\frac{dP}{dT} = \frac{\Delta H}{T \Delta V} < 0.

  3. For COX2\ce{CO2}, solid dry ice is denser than liquid COX2\ce{CO2}, so Vliquid>VsolidV_{\text{liquid}} > V_{\text{solid}}, giving ΔVfus>0\Delta V_{\text{fus}} > 0. Therefore, dPdT>0\frac{dP}{dT} > 0.

  4. Evaluate increasing pressure just below the melting point: for HX2O\ce{H2O}, the negative slope shifts the equilibrium so that pressure favors the denser liquid phase (causes melting); for COX2\ce{CO2}, the positive slope means pressure favors the denser solid phase (prevents melting).

Final answer

(a) dPdT\frac{dP}{dT} is negative (−-) for HX2O\ce{H2O} and positive (++) for COX2\ce{CO2}; (b) For HX2O\ce{H2O}, increasing pressure causes melting; for COX2\ce{CO2}, increasing pressure prevents melting.

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the universal definition of Δ\Delta in thermodynamics as final−initial\text{final} - \text{initial}.

  • Practice sketch-checking phase boundaries using Le Chatelier's principle.

OverviewACEpath Teacher's Diagnosis

02 The student misinterprets a negative solid-liquid slope, assuming a negative slope means higher pressure corresponds to higher melting temperature.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    ΔHfusion>0\Delta H_{\text{fusion}} > 0 For H2O\text{H}_2\text{O}, V=1ρV = \frac{1}{\rho}, Vliquid<Vsolid  ⟹  ΔV=Vliquid−Vsolid<0  ⟹  dPdT=ΔHTΔV<0 (negative)V_{\text{liquid}} < V_{\text{solid}} \implies \Delta V = V_{\text{liquid}} - V_{\text{solid}} < 0 \implies \frac{dP}{dT} = \frac{\Delta H}{T\Delta V} < 0\text{ (negative)} For CO2\text{CO}_2, Vliquid>Vsolid  ⟹  ΔV=Vliquid−Vsolid>0  ⟹  dPdT=ΔHTΔV>0 (positive)V_{\text{liquid}} > V_{\text{solid}} \implies \Delta V = V_{\text{liquid}} - V_{\text{solid}} > 0 \implies \frac{dP}{dT} = \frac{\Delta H}{T\Delta V} > 0\text{ (positive)}

  2. Step 2

    For H2O\text{H}_2\text{O}, dPdT\frac{dP}{dT} is negative, so increasing pressure shifts equilibrium to the solid and prevents melting. ⟹ For CO2\text{CO}_2, dPdT\frac{dP}{dT} is positive, so increasing pressure shifts equilibrium to the liquid and causes melting.

    Correct

    For H2O\text{H}_2\text{O}, increasing pressure causes melting. For CO2\text{CO}_2, increasing pressure prevents melting (favors the solid).

    Increasing pressure always shifts a phase equilibrium toward the denser phase (the one with smaller volume). For H2O\text{H}_2\text{O}, liquid water is denser than ice (Vliquid<VsolidV_{\text{liquid}} < V_{\text{solid}}), so higher pressure favors the liquid and causes melting. On a P-TP\text{-}T diagram where the melting line has a negative slope (tilting left), moving vertically upward (increasing PP) at a temperature just below the normal melting point crosses from the solid region into the liquid region. For CO2\text{CO}_2, the solid is denser, so higher pressure stabilizes the solid and prevents melting.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly established that ΔHfusion>0\Delta H_{\text{fusion}} > 0 for melting.

You accurately linked density to specific volume to find the sign of ΔV\Delta V for both substances.

You correctly deduced that dPdT\frac{dP}{dT} is negative for H2O\text{H}_2\text{O} and positive for CO2\text{CO}_2.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Thermodynamic phase equilibrium / Le Chatelier misapplication

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You inverted the relationship between pressure, phase boundary slope, and phase stability. According to Le Chatelier's principle, an increase in pressure favors the phase with smaller volume (higher density). Alternatively, on a P-TP\text{-}T plot with PP on the vertical axis, moving upward at constant TT moves across a negatively sloped boundary into the liquid phase (for water), and stays in/enters the solid phase across a positively sloped boundary (for CO2\text{CO}_2).

REASONING PATH
Your ACEpath teacher’s suggested approach
Pressure and Density Rule
  • By Le Chatelier's principle, increasing pressure shifts the system toward whichever phase has the higher density (smaller volume).

  • Compare ρsolid\rho_{\text{solid}} and ρliquid\rho_{\text{liquid}}. Whichever is larger is the phase stabilized by higher pressure.

Phase Diagram Geometry
  • On a P-TP\text{-}T phase diagram (PP vertical, TT horizontal), the solid phase is at lower TT (left) and the liquid phase is at higher TT (right).

  • Draw a vertical line moving upward at T<TmT < T_m. If the solid-liquid line has dPdT<0\frac{dP}{dT} < 0 (tilts left), going up crosses from solid into liquid.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Recall that an increase in pressure shifts equilibrium toward the phase with higher density (smaller volume).

  2. For H2O\text{H}_2\text{O}: ρliquid>ρice\rho_{\text{liquid}} > \rho_{\text{ice}}, so increasing pressure favors the liquid phase. Moving vertically upward on a P-TP\text{-}T diagram across the negatively sloped boundary takes the solid into the liquid region, causing melting.

  3. For CO2\text{CO}_2: ρsolid>ρliquid\rho_{\text{solid}} > \rho_{\text{liquid}}, so increasing pressure favors the solid phase. The positively sloped line shifts the melting point higher, preventing melting.

Final answer

(a) dPdT\frac{dP}{dT} is negative for H2O\text{H}_2\text{O} and positive for CO2\text{CO}_2; (b) For H2O\text{H}_2\text{O}, increasing pressure causes melting; for CO2\text{CO}_2, increasing pressure prevents melting.

NEXT STEPS
Final Takeaways from Your Teacher
  • Review how Le Chatelier's principle applies to molar volume changes during phase transitions.

  • Practice sketching vertical lines of constant temperature on P-TP\text{-}T phase diagrams with positive vs. negative slopes to visualize phase changes as pressure increases.

OverviewACEpath Teacher's Diagnosis

03 The student confuses density and volume, erroneously concluding that higher liquid density means liquid volume is greater than solid volume.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    For HX2O, ρliquid>ρice means Vliquid>Vice, so ΔV>0  ⟹  dPdT=ΔHTΔV>0 (positive)\text{For } \ce{H2O},\ \rho_{\text{liquid}} > \rho_{\text{ice}} \text{ means } V_{\text{liquid}} > V_{\text{ice}}, \text{ so } \Delta V > 0 \implies \frac{dP}{dT} = \frac{\Delta H}{T \Delta V} > 0\text{ (positive)}

    Correct

    ρliquid>ρice  ⟹  Vliquid<Vice, so ΔVfus<0  ⟹  dPdT=ΔHfusTΔVfus<0 (negative)\rho_{\text{liquid}} > \rho_{\text{ice}} \implies V_{\text{liquid}} < V_{\text{ice}}, \text{ so } \Delta V_{\text{fus}} < 0 \implies \frac{dP}{dT} = \frac{\Delta H_{\text{fus}}}{T \Delta V_{\text{fus}}} < 0\text{ (negative)}

    Specific volume is inversely proportional to density (V=1ρV = \frac{1}{\rho}). Because liquid water is denser than ice, a given mass of liquid occupies less volume than the solid (Vliquid<ViceV_{\text{liquid}} < V_{\text{ice}}). Therefore, melting involves a contraction (ΔV<0\Delta V < 0), making dPdT\frac{dP}{dT} negative.

  2. Step 2

    For COX2, ρliquid<ρsolid means Vliquid<Vsolid, so ΔV<0  ⟹  dPdT=ΔHTΔV<0 (negative)\text{For } \ce{CO2},\ \rho_{\text{liquid}} < \rho_{\text{solid}} \text{ means } V_{\text{liquid}} < V_{\text{solid}}, \text{ so } \Delta V < 0 \implies \frac{dP}{dT} = \frac{\Delta H}{T \Delta V} < 0\text{ (negative)}

    Correct

    ρliquid<ρsolid  ⟹  Vliquid>Vsolid, so ΔVfus>0  ⟹  dPdT=ΔHfusTΔVfus>0 (positive)\rho_{\text{liquid}} < \rho_{\text{solid}} \implies V_{\text{liquid}} > V_{\text{solid}}, \text{ so } \Delta V_{\text{fus}} > 0 \implies \frac{dP}{dT} = \frac{\Delta H_{\text{fus}}}{T \Delta V_{\text{fus}}} > 0\text{ (positive)}

    Because solid COX2\ce{CO2} is denser than liquid COX2\ce{CO2}, melting results in an expansion (Vliquid>VsolidV_{\text{liquid}} > V_{\text{solid}}, so ΔV>0\Delta V > 0). Since ΔHfus>0\Delta H_{\text{fus}} > 0 and T>0T > 0, the slope dPdT\frac{dP}{dT} is positive.

  3. Step 3

    For HX2O, since dPdT>0, increasing pressure increases the melting point, preventing melting.\text{For } \ce{H2O}, \text{ since } \frac{dP}{dT} > 0, \text{ increasing pressure increases the melting point, preventing melting.}

    Correct

    For HX2O, since dPdT<0, increasing pressure lowers the melting point, causing melting.\text{For } \ce{H2O}, \text{ since } \frac{dP}{dT} < 0, \text{ increasing pressure lowers the melting point, causing melting.}

    Your reasoning that a positive slope means pressure increases the melting point is logically sound, but it follows from the incorrect sign determined in part (a). Because dPdT<0\frac{dP}{dT} < 0, applying pressure lowers the melting point and drives the solid into the denser liquid phase, causing melting.

  4. Step 4

    For COX2, since dPdT<0, increasing pressure decreases the melting point, causing melting.\text{For } \ce{CO2}, \text{ since } \frac{dP}{dT} < 0, \text{ increasing pressure decreases the melting point, causing melting.}

    Correct

    For COX2, since dPdT>0, increasing pressure raises the melting point, preventing melting.\text{For } \ce{CO2}, \text{ since } \frac{dP}{dT} > 0, \text{ increasing pressure raises the melting point, preventing melting.}

    This conclusion is carried over from the inverted sign in part (a). Because the true slope is positive (dPdT>0\frac{dP}{dT} > 0), increasing pressure raises the melting temperature and stabilizes the denser solid phase, preventing melting.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified the Clapeyron equation dPdT=ΔHTΔV\frac{dP}{dT} = \frac{\Delta H}{T \Delta V} as the governing relationship.

You recognized that ΔHfus>0\Delta H_{\text{fus}} > 0 and T>0T > 0, so the algebraic sign of dPdT\frac{dP}{dT} depends entirely on the sign of ΔV\Delta V.

You demonstrated consistent graphical interpretation by linking the sign of dPdT\frac{dP}{dT} to how melting temperature shifts under applied pressure.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverse Relationship Confusion

You treated density and volume as directly proportional instead of inversely proportional when evaluating ΔV\Delta V.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing density (ρ=mV\rho = \frac{m}{V}) with volume led to the mistaken assumption that higher density corresponds to larger volume, which inverted the sign of ΔVfus=Vliquid−Vsolid\Delta V_{\text{fus}} = V_{\text{liquid}} - V_{\text{solid}} for both substances.

REASONING PATH
Your ACEpath teacher’s suggested approach
Density-to-Volume Inversion
  • For a fixed mass mm, molar or specific volume is inversely proportional to density: V=mρV = \frac{m}{\rho}.

  • Always write ΔVfus=1ρliquid−1ρsolid\Delta V_{\text{fus}} = \frac{1}{\rho_{\text{liquid}}} - \frac{1}{\rho_{\text{solid}}} so that ρliquid>ρsolid\rho_{\text{liquid}} > \rho_{\text{solid}} immediately yields ΔVfus<0\Delta V_{\text{fus}} < 0.

Le Chatelier and Phase Density
  • Increasing pressure always shifts equilibrium toward the phase with higher density (smaller volume).

  • Check your final answer against density: since liquid water is denser than ice, compression must favor liquid water (causes melting).

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Apply the inverse relationship V=1ρV = \frac{1}{\rho}: for HX2O\ce{H2O}, ρliquid=0.9998>ρice=0.9167  ⟹  Vliquid<Vice  ⟹  ΔVfus<0\rho_{\text{liquid}} = 0.9998 > \rho_{\text{ice}} = 0.9167 \implies V_{\text{liquid}} < V_{\text{ice}} \implies \Delta V_{\text{fus}} < 0.

  2. For COX2\ce{CO2}, ρsolid=1.56>ρliquid=1.18  ⟹  Vliquid>Vsolid  ⟹  ΔVfus>0\rho_{\text{solid}} = 1.56 > \rho_{\text{liquid}} = 1.18 \implies V_{\text{liquid}} > V_{\text{solid}} \implies \Delta V_{\text{fus}} > 0.

  3. Substitute into the Clapeyron equation dPdT=ΔHfusTΔVfus\frac{dP}{dT} = \frac{\Delta H_{\text{fus}}}{T \Delta V_{\text{fus}}} with ΔHfus>0\Delta H_{\text{fus}} > 0 and T>0T > 0: dPdT<0\frac{dP}{dT} < 0 (negative) for HX2O\ce{H2O}, and dPdT>0\frac{dP}{dT} > 0 (positive) for COX2\ce{CO2}.

  4. Analyze the effect of increasing pressure just below the melting point: for HX2O\ce{H2O}, the negative slope means moving vertically upward on a P-TP\text{-}T diagram crosses into the liquid region (causes melting); for COX2\ce{CO2}, the positive slope means moving vertically upward stays in the solid region (prevents melting).

Final answer

(a) dPdT\frac{dP}{dT} is negative (−-) for HX2O\ce{H2O} and positive (++) for COX2\ce{CO2}; (b) For HX2O\ce{H2O}, increasing pressure causes melting; for COX2\ce{CO2}, increasing pressure prevents melting.

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the definition of specific and molar volume as V=1ρV = \frac{1}{\rho} to avoid equating higher density with larger volume.

  • Practice sketching P-TP\text{-}T phase diagrams with both negative (water-like) and positive (typical) melting slopes, tracing vertical pressure arrows at constant TT.

Lock it in

Similar question

01

Elemental bismuth expands upon freezing (its solid density is 9.78 g/cm39.78\text{ g/cm}^3 and its liquid density is 10.05 g/cm310.05\text{ g/cm}^3). Determine the sign of the slope dPdT\frac{dP}{dT} of its solid-liquid equilibrium boundary.

Answer

Negative (−-). For melting, ΔVfus=Vliquid−Vsolid=110.05−19.78<0\Delta V_{\text{fus}} = V_{\text{liquid}} - V_{\text{solid}} = \frac{1}{10.05} - \frac{1}{9.78} < 0. Since ΔHfus>0\Delta H_{\text{fus}} > 0 and T>0T > 0, dPdT=ΔHTΔV<0\frac{dP}{dT} = \frac{\Delta H}{T \Delta V} < 0.

02

Benzene has a standard enthalpy of fusion ΔHfus=+9.87 kJ/mol\Delta H_{\text{fus}} = +9.87\text{ kJ/mol} at its normal melting point of 5.5∘C5.5^\circ\text{C} (278.7 K278.7\text{ K}). Upon melting, its molar volume increases by +10.3 cm3/mol+10.3\text{ cm}^3/\text{mol}. Calculate the slope dPdT\frac{dP}{dT} in bar/K\text{bar/K} (given 1 J=10 cm3⋅bar1\text{ J} = 10\text{ cm}^3\cdot\text{bar}).

Answer

≈34.4 bar/K\approx 34.4\text{ bar/K}. Convert ΔHfus=9870 J/mol=98700 cm3⋅bar/mol\Delta H_{\text{fus}} = 9870\text{ J/mol} = 98700\text{ cm}^3\cdot\text{bar/mol}. Using the Clapeyron equation: dPdT=98700 cm3⋅bar/mol278.7 K×10.3 cm3/mol≈34.4 bar/K\frac{dP}{dT} = \frac{98700\text{ cm}^3\cdot\text{bar/mol}}{278.7\text{ K} \times 10.3\text{ cm}^3/\text{mol}} \approx 34.4\text{ bar/K}.

03

A substance exhibits a negative fusion slope dPdT<0\frac{dP}{dT} < 0. If an external pressure of 500 atm500\text{ atm} is applied to a sample existing at solid-liquid equilibrium, will its melting temperature increase, decrease, or remain unchanged? Explain using the differential relationship.

Answer

It will decrease. Because dPdT<0\frac{dP}{dT} < 0, taking the reciprocal gives dTfusdP<0\frac{dT_{\text{fus}}}{dP} < 0. Therefore, an increase in pressure (dP>0dP > 0) causes a negative change in melting temperature (dTfus<0dT_{\text{fus}} < 0).

Loading workspace…