Resources

An analytical chemistry student standardizes an unknown copper(II) solution via flame atomic emission spectrophotometry. To clean the platinum wire loop prior to testing, the standard operating procedure requires dipping the loop into concentrated hydrochloric acid (HCl\text{HCl}, 12 M12\text{ M}) and heating it in the flame until no color is observed. (a) Explain the chemical rationale for converting metal oxides or carbonates on the wire loop into metal chlorides using concentrated HCl\text{HCl} rather than using concentrated sulfuric acid (H2SO4\text{H}_2\text{SO}_4). (b) When the cleaned wire is dipped into the unknown solution and introduced into the flame, a distinct emerald-green coloration is observed, and the spectrometer records a major peak at λ=510.6 nm\lambda = 510.6\text{ nm}. Confirm the element and calculate the frequency ν\nu of this transition in hertz (Hz\text{Hz}) (c=2.998×108 m/sc = 2.998 \times 10^8\text{ m/s}). (c) If a student accidentally used an uncleaned nichrome wire contaminated with 1.50×10−8 g1.50 \times 10^{-8}\text{ g} of sodium ions (Na+\text{Na}^+), calculate the number of sodium atoms present on the wire and explain why this tiny contaminant can completely mask the copper emission visually (MNa=22.99 g/molM_{\text{Na}} = 22.99\text{ g/mol}, NA=6.022×1023 atoms/molN_A = 6.022 \times 10^{23}\text{ atoms/mol}).

Answer and steps

Final answer

(a) Metal chlorides have substantially lower lattice energies and higher volatilities (lower boiling/sublimation points) than sulfates or oxides, ensuring rapid atomization and vaporization into the gas phase within the flame zone; (b) The element is copper (Cu\text{Cu}); frequency ν=5.872×1014 Hz\nu = 5.872 \times 10^{14}\text{ Hz}; (c) Natoms=3.93×1014 atomsN_{\text{atoms}} = 3.93 \times 10^{14}\text{ atoms}; because sodium has an exceptionally large oscillator strength and transition cross-section at 589 nm589\text{ nm}, even sub-microgram quantities produce millions of intense photons per millisecond in the region of maximum human eye sensitivity.

Steps

Part (a): Chemical Rationale for Using Concentrated HCl\ce{HCl}

In flame tests and flame emission spectrophotometry, the sample must undergo rapid vaporization and atomization into the gaseous state within the flame:

MClXn(s)→MClXn(g)→M(g)+nCl(g)\ce{MCl_n(s) -> MCl_n(g) -> M(g) + } n\ce{Cl(g)}

  • Volatility and Lattice Energy: Metal chlorides generally have significantly lower lattice energies and higher volatilities (substantially lower boiling or sublimation points) compared to corresponding metal sulfates or oxides.
  • Cleaning Wire Loops: Concentrated hydrochloric acid (HCl\ce{HCl}) converts persistent metal oxides or carbonates on the wire loop into volatile metal chlorides that vaporize easily when heated, leaving a clean wire that imparts no background color to the flame.
  • Why Not HX2SOX4\ce{H2SO4}? Concentrated sulfuric acid (HX2SOX4\ce{H2SO4}) would convert the metal residues into metal sulfates. Sulfates have very high thermal stabilities and low volatilities; they do not readily vaporize in a standard flame, leaving non-volatile deposits that contaminate future measurements.

Part (b): Element Identification and Frequency Calculation

  1. Element Confirmation: The emerald-green flame color along with an emission line at λ=510.6 nm\lambda = 510.6\text{ nm} is characteristic of copper (Cu\ce{Cu}).
  2. Frequency Calculation: The relationship between the speed of light (cc), wavelength (λ\lambda), and frequency (ν\nu) is given by:

    c=λν  ⟹  ν=cλc = \lambda \nu \implies \nu = \frac{c}{\lambda}

    Convert the given wavelength into meters: λ=510.6 nm=510.6×10−9 m\lambda = 510.6\text{ nm} = 510.6 \times 10^{-9}\text{ m}

    Substitute the values into the wave equation: ν=2.998×108 m/s510.6×10−9 m=5.8715×1014 s−1≈5.872×1014 Hz\nu = \frac{2.998 \times 10^8\text{ m/s}}{510.6 \times 10^{-9}\text{ m}} = 5.8715 \times 10^{14}\text{ s}^{-1} \approx 5.872 \times 10^{14}\text{ Hz}


Part (c): Calculation of Contaminant Sodium Atoms and Masking Effect

  1. Calculate Moles of Sodium: nNa=mM=1.50×10−8 g22.99 g/mol=6.5246×10−10 moln_{\ce{Na}} = \frac{m}{M} = \frac{1.50 \times 10^{-8}\text{ g}}{22.99\text{ g/mol}} = 6.5246 \times 10^{-10}\text{ mol}
  2. Calculate the Number of Sodium Atoms: Using Avogadro's number (NA=6.022×1023 atoms/molN_A = 6.022 \times 10^{23}\text{ atoms/mol}): Natoms=nNa⋅NA=(6.5246×10−10 mol)⋅(6.022×1023 atoms/mol)=3.929×1014 atoms≈3.93×1014 atomsN_{\text{atoms}} = n_{\ce{Na}} \cdot N_A = (6.5246 \times 10^{-10}\text{ mol}) \cdot (6.022 \times 10^{23}\text{ atoms/mol}) = 3.929 \times 10^{14}\text{ atoms} \approx 3.93 \times 10^{14}\text{ atoms}
  3. Why Trace Sodium Masks the Copper Emission:

    • Transition Probability (Oscillator Strength): Sodium possesses an extraordinarily high transition probability and large oscillator strength for its resonance doublet (the 3p→3s\ce{3p -> 3s} sodium D-lines at 589.0 nm589.0\text{ nm} and 589.6 nm589.6\text{ nm}). Consequently, even a minuscule trace of sodium atoms yields millions of emitted photons per millisecond.
    • Human Visual Sensitivity: The human eye's photopic sensitivity curve peaks near 555 nm555\text{ nm} (in the green-yellow region) and remains extremely sensitive around 589 nm589\text{ nm}. The overwhelming brightness of this yellow-orange emission easily drowns out the weaker emerald-green emission of copper to the naked eye.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets to convert the wavelength from nanometers to meters before calculating frequency, resulting in a value off by nine orders of magnitude.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Metal chlorides have high volatility and vaporize easily in the flame to clean the wire, while sulfates have very low volatility and persist.

  2. Step 2

    The element is copper (Cu).

  3. Step 3

    ν=cλ  ⟹  ν=(2.998×108 m/s)/510.6  ⟹  ν=5.872×105 Hz\nu = \frac{c}{\lambda} \implies \nu = (2.998 \times 10^8\text{ m/s}) / 510.6 \implies \nu = 5.872 \times 10^5\text{ Hz}

    Correct

    ν=cλ=2.998×108 m/s510.6×10−9 m≈5.872×1014 Hz\nu = \frac{c}{\lambda} = \frac{2.998 \times 10^8\text{ m/s}}{510.6 \times 10^{-9}\text{ m}} \approx 5.872 \times 10^{14}\text{ Hz}

    You divided the speed of light in meters per second by the wavelength directly in nanometers without converting to meters (1 nm=10−9 m1\text{ nm} = 10^{-9}\text{ m}), which reduced the frequency by a factor of 10910^9.

  4. Step 4

    n=(1.50×10−8 g)/(22.99 g/mol)=6.525×10−10 mol  ⟹  N=(6.525×10−10 mol)×(6.022×1023 atoms/mol)=3.93×1014 atomsn = (1.50 \times 10^{-8}\text{ g}) / (22.99\text{ g/mol}) = 6.525 \times 10^{-10}\text{ mol} \implies N = (6.525 \times 10^{-10}\text{ mol}) \times (6.022 \times 10^{23}\text{ atoms/mol}) = 3.93 \times 10^{14}\text{ atoms}

  5. Step 5

    Sodium emits extremely intense yellow light that overpowers the weaker green flame visually because the human eye is very sensitive to yellow.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified copper from its characteristic green flame emission.

You provided an accurate physical explanation for the cleaning efficiency of concentrated HCl\text{HCl} over H2SO4\text{H}_2\text{SO}_4.

You correctly executed the multi-step stoichiometry to determine the number of sodium atoms.

You correctly explained why trace sodium emission visually dominates the copper flame.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Unit Conversion Error

You initially considered a power of ten but crossed it out and divided the speed of light directly by the wavelength in nanometers.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Failing to enforce SI base unit consistency (1 nm=10−9 m1\text{ nm} = 10^{-9}\text{ m}) before evaluating c=λνc = \lambda \nu.

REASONING PATH
Your ACEpath teacher’s suggested approach
Unit Consistency Check
  • In wave equations where velocity is in meters per second (m/s\text{m/s}), wavelength λ\lambda must be converted to meters (m\text{m}) so that distance units cancel: m/sm=s−1=Hz\frac{\text{m/s}}{\text{m}} = \text{s}^{-1} = \text{Hz}.

  • Whenever a wavelength is given in nanometers (nm\text{nm}), immediately replace nm\text{nm} with ×10−9 m\times 10^{-9}\text{ m} before entering it into your calculation.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert the given wavelength to meters: λ=510.6 nm=510.6×10−9 m\lambda = 510.6\text{ nm} = 510.6 \times 10^{-9}\text{ m}.

  2. Substitute into ν=cλ\nu = \frac{c}{\lambda}: ν=2.998×108 m/s510.6×10−9 m\nu = \frac{2.998 \times 10^8\text{ m/s}}{510.6 \times 10^{-9}\text{ m}}.

  3. Evaluate the quotient: ν=5.8715×1014 s−1≈5.872×1014 Hz\nu = 5.8715 \times 10^{14}\text{ s}^{-1} \approx 5.872 \times 10^{14}\text{ Hz}.

Final answer

(a) Chlorides are much more volatile than sulfates; (b) Copper (Cu\text{Cu}), ν=5.872×1014 Hz\nu = 5.872 \times 10^{14}\text{ Hz}; (c) 3.93×1014 atoms3.93 \times 10^{14}\text{ atoms}, intense yellow emission overpowers weaker green emission visually.

NEXT STEPS
Final Takeaways from Your Teacher
  • Always write out explicit units inside substitution steps to verify that m\text{m} cancels with m\text{m}.

  • Memorize common metric prefixes for spectroscopy: nm=10−9 m\text{nm} = 10^{-9}\text{ m}, μm=10−6 m\mu\text{m} = 10^{-6}\text{ m}, and A˚=10−10 m\text{\AA} = 10^{-10}\text{ m}.

OverviewACEpath Teacher's Diagnosis

02 The student inverts the calculation of moles by multiplying mass by molar mass instead of dividing, producing an incorrect atom count.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Metal chlorides vaporize much more easily due to higher volatility than metal sulfates, leaving the wire clean.

  2. Step 2

    The element is copper (Cu). ⟹ λ=510.6×10−9 m\lambda = 510.6 \times 10^{-9}\text{ m} ⟹ ν=c/λ=(2.998×108 m/s)/(510.6×10−9 m)=5.872×1014 Hz\nu = c/\lambda = (2.998 \times 10^8\text{ m/s}) / (510.6 \times 10^{-9}\text{ m}) = 5.872 \times 10^{14}\text{ Hz}

  3. Step 3

    n=(1.50×10−8 g)×(22.99 g/mol)=3.449×10−7 moln = (1.50 \times 10^{-8}\text{ g}) \times (22.99\text{ g/mol}) = 3.449 \times 10^{-7}\text{ mol}

    Correct

    n=mM=1.50×10−8 g22.99 g/mol=6.525×10−10 moln = \frac{m}{M} = \frac{1.50 \times 10^{-8}\text{ g}}{22.99\text{ g/mol}} = 6.525 \times 10^{-10}\text{ mol}

    To convert mass to amount of substance, you must divide mass by molar mass (n=m/Mn = m/M), but you multiplied them instead, giving units of g2/mol\text{g}^2/\text{mol}.

  4. Step 4

    N=(3.449×10−7 mol)×(6.022×1023 atoms/mol)=2.08×1017 atomsN = (3.449 \times 10^{-7}\text{ mol}) \times (6.022 \times 10^{23}\text{ atoms/mol}) = 2.08 \times 10^{17}\text{ atoms}

    Correct

    N=n⋅NA=(6.525×10−10 mol)×(6.022×1023 atoms/mol)=3.93×1014 atomsN = n \cdot N_A = (6.525 \times 10^{-10}\text{ mol}) \times (6.022 \times 10^{23}\text{ atoms/mol}) = 3.93 \times 10^{14}\text{ atoms}

    You used the correct relationship N=n⋅NAN = n \cdot N_A, but the value was thrown off by the incorrect mole value calculated in the previous step.

  5. Step 5

    Sodium has an extremely high emission intensity in the yellow region where human vision is highly sensitive, overwhelming the green copper emission.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly explained the chemical rationale for forming volatile metal chlorides with concentrated hydrochloric acid.

You correctly identified copper from its characteristic emerald-green flame and calculated the frequency of the 510.6 nm510.6\text{ nm} emission line.

You accurately explained why trace sodium emission visually overwhelms copper emission based on flame intensity and human photopic vision.

You correctly applied Avogadro's constant to relate moles to total number of atoms.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Dimensional Analysis Inversion

You accidentally multiplied mass by molar mass instead of dividing mass by molar mass when converting grams of sodium to moles.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Losing track of dimensional analysis during mole conversions causes inverted operations (m×Mm \times M instead of m/Mm / M).

REASONING PATH
Your ACEpath teacher’s suggested approach
Dimensional Unit Check
  • Moles have units of mol\text{mol}, so mass (g\text{g}) must be divided by molar mass (g/mol\text{g}/\text{mol}): gg/mol=mol\frac{\text{g}}{\text{g}/\text{mol}} = \text{mol}.

  • Always write out explicit units: multiplying g×(g/mol)\text{g} \times (\text{g}/\text{mol}) yields g2/mol\text{g}^2/\text{mol}, which immediately flags an inverted operation.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Divide mass by molar mass: n=1.50×10−8 g22.99 g/mol=6.525×10−10 moln = \frac{1.50 \times 10^{-8}\text{ g}}{22.99\text{ g/mol}} = 6.525 \times 10^{-10}\text{ mol}.

  2. Multiply moles by Avogadro's number: N=(6.525×10−10 mol)×(6.022×1023 atoms/mol)=3.93×1014 atomsN = (6.525 \times 10^{-10}\text{ mol}) \times (6.022 \times 10^{23}\text{ atoms/mol}) = 3.93 \times 10^{14}\text{ atoms}.

Final answer

3.93×1014 atoms3.93 \times 10^{14}\text{ atoms}

NEXT STEPS
Final Takeaways from Your Teacher
  • Write out units explicitly during mass-to-mole conversions so you can cancel grams.

  • Practice converting very small masses (micrograms, nanograms) to moles and particle counts using dimensional analysis grids.

OverviewACEpath Teacher's Diagnosis

03 The student misattributes the acid choice to acid strength rather than volatility, claiming HCl is used because it is a stronger acid that dissolves oxides more completely.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Hydrochloric acid is a much stronger monoprotic acid than sulfuric acid, so it completely ionizes to dissolve and react with insoluble metal oxides and carbonates faster.

    Correct

    Concentrated HCl\ce{HCl} converts metal oxides and carbonates into metal chlorides, which have lower lattice energies and higher volatilities than metal sulfates or oxides, allowing them to vaporize and atomize rapidly in the flame to leave a clean wire.

    Both HCl\ce{HCl} and HX2SOX4\ce{H2SO4} are strong acids capable of reacting with basic oxides and carbonates. The critical difference is that metal chlorides have significantly lower lattice energies and higher volatilities (substantially lower boiling/sublimation points) than metal sulfates. Chlorides vaporize completely away in the flame zone, whereas sulfates form non-volatile, thermally stable residues that persistently contaminate the wire.

  2. Step 2

    The element is copper (Cu).   ⟹  λ=510.6×10−9 m  ⟹  ν=cλ=2.998×108 m/s510.6×10−9 m=5.872×1014 Hz\implies \lambda = 510.6 \times 10^{-9}\text{ m} \implies \nu = \frac{c}{\lambda} = \frac{2.998 \times 10^8\text{ m/s}}{510.6 \times 10^{-9}\text{ m}} = 5.872 \times 10^{14}\text{ Hz}

  3. Step 3

    n=1.50×10−8 g22.99 g/mol=6.525×10−10 mol  ⟹  N=(6.525×10−10 mol)×(6.022×1023 atoms/mol)=3.93×1014 atoms  ⟹  n = \frac{1.50 \times 10^{-8}\text{ g}}{22.99\text{ g/mol}} = 6.525 \times 10^{-10}\text{ mol} \implies N = (6.525 \times 10^{-10}\text{ mol}) \times (6.022 \times 10^{23}\text{ atoms/mol}) = 3.93 \times 10^{14}\text{ atoms} \implies Sodium emits brilliant yellow light with high transition probability and human visual sensitivity, visually masking the fainter emerald-green copper flame.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified copper as the emitter of the emerald-green flame.

You accurately converted nanometers to meters and computed the spectral transition frequency.

You correctly calculated the molar quantity and total number of sodium contaminant atoms using Avogadro's number.

You accurately linked sodium's high transition probability and human eye sensitivity to visual masking.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Acid Volatility Misconception

Attributing the choice of cleaning acid to comparative acid ionization strength rather than salt volatility.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You focused on aqueous solution-phase acid-base dissolution rather than the high-temperature flame requirements of low lattice energy and vapor-phase volatility for atomization.

REASONING PATH
Your ACEpath teacher’s suggested approach
Role of Cleaning Acid in Flame Spectroscopy
  • Cleaning reagents must convert non-volatile contaminants into salts that readily sublimate or vaporize at burner temperatures (1000–1800∘C1000\text{--}1800^\circ\text{C}).

  • Select hydrochloric acid because metal chlorides possess low lattice energies and high vapor pressures, ensuring complete volatilization off the wire loop.

Chloride vs. Sulfate Volatility
  • Metal sulfates have higher lattice energies and decompose into refractory oxides or stable solids rather than vaporizing cleanly.

  • Avoid sulfuric acid for wire loop cleaning because resulting sulfates will not burn off, causing cross-contamination.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Identify the physical phase requirement of flame emission: metal species must enter the gas phase as free atoms (M(g)\ce{M(g)}) within the flame.

  2. Compare the thermal properties of metal chlorides versus metal sulfates: metal chlorides have lower lattice energies and sublime/boil at significantly lower temperatures than sulfates.

  3. Conclude that concentrated HCl\ce{HCl} produces volatile chloride salts that burn away rapidly, leaving a clean wire, whereas HX2SOX4\ce{H2SO4} leaves refractory, non-volatile sulfate residues.

Final answer

(a) Concentrated HCl\ce{HCl} forms volatile metal chlorides with low lattice energies that readily vaporize into the gas phase, whereas HX2SOX4\ce{H2SO4} forms refractory, non-volatile sulfates; (b) Copper (Cu\ce{Cu}), ν=5.872×1014 Hz\nu = 5.872 \times 10^{14}\text{ Hz}; (c) N=3.93×1014 atomsN = 3.93 \times 10^{14}\text{ atoms}, masked by high transition probability and human eye sensitivity.

NEXT STEPS
Final Takeaways from Your Teacher
  • Review how lattice energy influences salt volatility and sublimation temperatures.

  • Remember that flame spectroscopy always requires gas-phase atomization, making volatility the primary criterion for pre-treatment salts.

  • Practice distinguishing between aqueous solution reactivity (acid strength) and solid-state thermal properties (volatility/lattice energy).

Lock it in

Similar question

01

A lithium flame test exhibits a crimson red emission at λ=670.8 nm\lambda = 670.8\text{ nm}. Calculate the frequency of this emission in hertz (c=2.998×108 m/sc = 2.998 \times 10^8\text{ m/s}).

Answer

Convert λ=670.8×10−9 m\lambda = 670.8 \times 10^{-9}\text{ m}. Then ν=cλ=2.998×108 m/s670.8×10−9 m=4.469×1014 Hz\nu = \frac{c}{\lambda} = \frac{2.998 \times 10^8\text{ m/s}}{670.8 \times 10^{-9}\text{ m}} = 4.469 \times 10^{14}\text{ Hz}.

02

An unknown alkali metal produces a violet flame with a major spectral line at a frequency of ν=7.41×1014 Hz\nu = 7.41 \times 10^{14}\text{ Hz}. Determine its wavelength in nanometers (nm\text{nm}) and identify the alkali metal (c=2.998×108 m/sc = 2.998 \times 10^8\text{ m/s}).

Answer

λ=cν=2.998×108 m/s7.41×1014 s−1=4.05×10−7 m=405 nm\lambda = \frac{c}{\nu} = \frac{2.998 \times 10^8\text{ m/s}}{7.41 \times 10^{14}\text{ s}^{-1}} = 4.05 \times 10^{-7}\text{ m} = 405\text{ nm}. A violet flame at 405 nm405\text{ nm} is characteristic of potassium (K\text{K}).

03

A sodium vapor lamp emits light at λ=589.0 nm\lambda = 589.0\text{ nm}. Calculate the energy of a single emitted photon in joules and the total energy per mole of photons in kilojoules (h=6.626×10−34 J⋅sh = 6.626 \times 10^{-34}\text{ J}\cdot\text{s}, c=2.998×108 m/sc = 2.998 \times 10^8\text{ m/s}, NA=6.022×1023 mol−1N_A = 6.022 \times 10^{23}\text{ mol}^{-1}).

Answer

λ=589.0×10−9 m\lambda = 589.0 \times 10^{-9}\text{ m}. Single photon energy: E=hcλ=(6.626×10−34 J⋅s)(2.998×108 m/s)589.0×10−9 m=3.373×10−19 JE = \frac{hc}{\lambda} = \frac{(6.626 \times 10^{-34}\text{ J}\cdot\text{s})(2.998 \times 10^8\text{ m/s})}{589.0 \times 10^{-9}\text{ m}} = 3.373 \times 10^{-19}\text{ J}. Molar energy: Emol=(3.373×10−19 J)(6.022×1023 mol−1)×10−3 kJ/J=203.1 kJ/molE_{\text{mol}} = (3.373 \times 10^{-19}\text{ J})(6.022 \times 10^{23}\text{ mol}^{-1}) \times 10^{-3}\text{ kJ/J} = 203.1\text{ kJ/mol}.

Loading workspace…