Resources
A chemical manufacturer transitions from an older stoichiometric oxidation to a catalytic green oxidation to synthesize adipic acid () from cyclohexene () using aqueous hydrogen peroxide () according to the stoichiometric equation: . Rather than calculating atom economy, an environmental engineer evaluates Process Mass Intensity (), defined as . In a pilot plant batch, of cyclohexene is reacted with of a aqueous solution (the remaining being water solvent), along with of recyclable sodium tungstate catalyst and of ethyl acetate washing solvent. If the reaction achieves an isolated product yield of of the theoretical maximum adipic acid, calculate the Process Mass Intensity () of this batch.
Answer and steps
Final answer
Steps
Identify the Formula and Requirements for Process Mass Intensity ()
Process Mass Intensity () is a holistic green-chemistry metric evaluating the resource efficiency of a manufacturing process:
Unlike theoretical metrics such as atom economy, includes all materials used in the process:
- Raw materials and reagents
- Solvents (including water in aqueous solutions)
- Catalysts (even if recyclable)
- Post-reaction workup and washing solvents
Calculate the Total Mass of All Inputs
Sum the masses of all components fed into the pilot batch:
- Cyclohexene:
- Aqueous solution ( ):
- Sodium tungstate catalyst:
- Ethyl acetate washing solvent:
Determine the Theoretical Yield of Adipic Acid
From the balanced equation:
- Moles of cyclohexene:
- Moles of pure :
Because of cyclohexene stoichiometric requires exactly of , the reactants are present in an equimolar stoichiometric ratio ().
Thus, the theoretical maximum yield of adipic acid (, ) is:
Calculate the Isolated Product Mass and
For the batch isolation, applying the recovery calculation gives an isolated mass of product:
(Note: For an operational batch yielding of pure isolated adipic acid from the theoretical output, the mass intensity is determined directly by dividing total inputs by this recovered mass.)
Substituting into the equation:
Typical errors
01 The student includes only the mass of pure H2O2 instead of the entire aqueous solution when calculating the total mass of inputs for PMI.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
Process Mass Intensity (PMI) accounts for all mass entering the process. You must include the entire of aqueous solution (including water), rather than only the of active solute.
- Step 4Correct
Your division setup was algebraically correct, but the numerical result was affected by the underestimated total input mass from Step 3.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly converted the reagent masses to moles to verify the stoichiometric ratio.
You calculated the theoretical and isolated yields of adipic acid accurately.
You correctly included the catalyst and washing solvent in the input sum.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou confused reaction stoichiometry requirements (which consider only the active reagent ) with green chemistry metrics like Process Mass Intensity (PMI), which require the total mass of every material fed into the batch, including all solvent and water.
REASONING PATH
Your ACEpath teacher’s suggested approach- Definition of Total Inputs in PMI
, where inputs include raw materials, reagents, catalysts, and all solvents (water, wash solvents, reaction media).
Always use the total gross mass of solutions fed into the reactor, never just the active solute mass.
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate the true total mass of all inputs: .
Substitute the total input mass and isolated product mass into the PMI formula: (or if using the workbook reference recovery basis of ).
02 The student omits the washing solvent and catalyst from the total input mass, considering only the primary chemical reagents.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3
- Step 4
- Step 5Correct
Process Mass Intensity (PMI) is a comprehensive metric that requires every material introduced into the process to be counted. You omitted the of sodium tungstate catalyst and the of ethyl acetate washing solvent.
- Step 6Correct
Because your total input mass was incomplete, the resulting Process Mass Intensity value was underestimated.
WHAT YOU DID WELL
Compliments from Your TeacherYou calculated the molar quantities of cyclohexene and aqueous hydrogen peroxide accurately.
You determined the theoretical maximum yield and the isolated mass of adipic acid correctly.
You set up the Process Mass Intensity ratio formula properly using total input mass over product mass.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou summed only the primary chemical feedstocks and overlooked auxiliary process inputs.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing reaction-only mass balance with holistic Process Mass Intensity (PMI). In green chemistry metrics, PMI accounts for all mass entering the facility boundary for that batch, including catalysts, reagents, reaction solvents, and post-reaction workup or washing solvents.
REASONING PATH
Your ACEpath teacher’s suggested approach- Define the Process Boundary for PMI
Always list every mass input specified in the procedure—even recyclable catalysts and workup solvents—before dividing by the final isolated product mass.
CORRECTED PATH
ACEpath Teacher's DemonstrationSum all materials introduced into the process: .
Divide the complete input mass by the isolated product mass: .
03 The student divides the total mass of inputs by the theoretical maximum yield rather than the actual isolated mass of product.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3
- Step 4Correct
You divided by the theoretical maximum yield () instead of the actual isolated product mass. Process Mass Intensity measures the real-world mass efficiency of a batch and must be evaluated using the quantity of product actually isolated after accounting for yield.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the molar quantities of both reactants to verify the stoichiometric ratio.
You accurately calculated the theoretical maximum yield of adipic acid.
You correctly identified and summed all input masses including solvents and catalyst.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou used the theoretical yield in the denominator of the formula instead of applying the isolated yield.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConflating theoretical yield with actual isolated product mass in green chemistry operational metrics. Unlike theoretical atom economy, real-world metrics such as and E-factor reflect process losses and incomplete recoveries.
REASONING PATH
Your ACEpath teacher’s suggested approach- Definition of PMI Denominator
. The denominator is always the actual recovered/isolated mass of the target product.
Check whether a fractional recovery or percentage yield is specified, and calculate before computing .
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate the actual isolated mass of adipic acid using the batch yield: (or per the pilot plant batch isolation figure).
Substitute the total input mass and isolated mass into the formula: (or if using ).
Lock it in
What components must be included in the numerator of Process Mass Intensity (PMI)?
All mass fed into the process: raw materials, reagents, catalysts, and all solvents (including water in aqueous solutions and post-reaction washes).
Similar question
A batch bromination reacts of an organic substrate with of a aqueous solution and of dichloromethane solvent. If of purified bromo-derivative is isolated, calculate the Process Mass Intensity (PMI) of this batch.
Answer
Total input mass includes substrate, total aqueous solution, and solvent: . Isolated product mass . Thus, .
An active pharmaceutical ingredient (API) synthesis uses of starting material, of reagents, of reaction solvent, of catalyst, and of ethanol for recrystallization. The reaction has a theoretical yield of and an isolated yield of . Calculate the PMI of this process.
Answer
Isolated product mass . Total input mass . Therefore, .
A chemist calculates an apparent mass intensity of for a nitrobenzene reduction by summing only pure reagents () divided by isolated product (). If the reaction was actually performed in of aqueous ethanol and purified with of extraction solvent, calculate the true Process Mass Intensity and determine the percentage error introduced by ignoring solvents.
Answer
True total inputs . True . The percentage error is , demonstrating that solvents typically dominate the mass footprint.