Resources
A student attempts to find the limiting reactant when of solid magnesium reacts with of molecular nitrogen gas to form magnesium nitride: . The student concludes that is the limiting reactant simply because its given mass () is smaller than the given mass of (). By determining the actual molar stoichiometric ratios and identifying the true limiting reactant, calculate the mass of unreacted excess reagent remaining after the reaction goes to completion. (Molar masses: , , ).
Answer and steps
Final answer
;
Steps
Identify the Pitfall in Comparing Masses Directly
A common error in stoichiometry is assuming that the reactant with the smaller initial mass is automatically the limiting reactant. Chemical reactions occur according to mole ratios, not mass ratios. Because different substances have different molar masses and stoichiometric coefficients, limiting reactants must always be determined by comparing available quantities in moles.
Convert Initial Masses to Moles
Using the given molar masses, calculate the initial amount of each reactant:
- For solid magnesium ():
- For molecular nitrogen ():
Determine the Limiting Reactant
The balanced chemical equation is:
This indicates that of are required for every of .
Calculate the moles of required to react completely with all available :
Compare the amount of needed to the amount of available:
- Because is supplied in far greater quantity than needed, is in excess.
- Magnesium () is completely consumed first, confirming that the true limiting reactant is .
Calculate the Remaining Mass of Excess Reagent
First, find the moles of left unreacted:
Next, convert the remaining moles of back to grams:
Typical errors
01 The student inverts the stoichiometric mole ratio by multiplying by 3 instead of dividing by 3 to find required nitrogen, concluding that N2 is the limiting reactant.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
According to the balanced equation , react with . To find the required moles of , you need to divide the moles of by (or multiply by ), rather than multiplying by .
- Step 3Correct
Because your calculated required moles of was too high due to the inverted ratio in Step 2, you concluded that nitrogen was limiting instead of magnesium.
- Step 4Correct
Because is actually the limiting reactant, all of is consumed, leaving unreacted with a mass of .
WHAT YOU DID WELL
Compliments from Your TeacherYou avoided the initial pitfall of comparing reactant masses directly.
You calculated the molar quantities of both magnesium and nitrogen gas accurately from their molar masses.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou accidentally multiplied the moles of magnesium by the coefficient instead of using the ratio .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisSetting up conversion factors without explicitly writing out and canceling the chemical units (e.g., writing just instead of ), which causes stoichiometric coefficients to be applied in the numerator rather than the denominator.
REASONING PATH
Your ACEpath teacher’s suggested approach- Use Dimensional Analysis with Units
Always write the formula as .
Check that the unit and substance name in the denominator cancel out the given reactant completely before completing the multiplication or division.
CORRECTED PATH
ACEpath Teacher's DemonstrationUse the mole ratio from : .
Compare needed vs. available: , so is in excess and is the true limiting reactant.
Find remaining moles of excess : .
Convert remaining moles of to mass: .
;
02 The student ignores the 3:1 stoichiometric coefficients in the chemical equation and treats the molar reaction ratio as 1:1.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
From the balanced equation , three moles of react with one mole of . The stoichiometric mole ratio of to is , not .
- Step 3Correct
Your conclusion that is limiting is correct because , but subtracting the wrong required moles propagated an error into the unreacted moles of .
- Step 4Correct
You multiplied the moles of unreacted nitrogen by its molar mass correctly, but the numerical value was affected by the stoichiometric ratio error in Step 2.
WHAT YOU DID WELL
Compliments from Your TeacherYou avoided comparing raw masses directly and converted both reactants to moles.
You used the correct molar masses for solid magnesium and nitrogen gas.
You correctly identified magnesium as the limiting reactant.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou set up a 1:1 molar ratio instead of using the ratio given by the coefficients in .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated reactants as reacting in equimolar amounts () rather than deriving the required mole ratio from the coefficients of the balanced chemical equation.
REASONING PATH
Your ACEpath teacher’s suggested approach- Use Coefficients for Mole Ratios
For a general reaction , the mole ratio needed is .
Always multiply or divide by the balanced equation's coefficients before comparing moles or calculating amounts consumed.
CORRECTED PATH
ACEpath Teacher's DemonstrationFind moles of required: .
Calculate unreacted moles of : .
Convert unreacted moles to mass: .
;
03 The student incorrectly uses atomic nitrogen (14.01 g/mol) instead of diatomic nitrogen (28.01 g/mol) to calculate the moles of nitrogen gas.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
Nitrogen gas exists as diatomic molecules (). You divided by the atomic mass of nitrogen () instead of the molecular molar mass ().
- Step 3
- Step 4Correct
Your subtraction and conversion method was logically sound, but the numerical result was affected by using the incorrect molar mass of nitrogen ( instead of ).
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly converted the mass of solid magnesium to moles using its molar mass.
You used the correct stoichiometric coefficient ratio () to calculate the required amount of nitrogen gas.
You correctly identified magnesium as the limiting reactant by comparing available amounts to required amounts.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou used the atomic molar mass of nitrogen () rather than the molecular molar mass of diatomic nitrogen gas () when calculating both initial and remaining quantities.
REASONING PATH
Your ACEpath teacher’s suggested approach- Check Elemental Formulas
Common elemental gases (, , , , , , ) exist as diatomic molecules.
Multiply the atomic weight by to calculate the molar mass whenever a diatomic gas formula is given.
- Consistency in Unit Conversions
The molar mass used to convert from grams to moles for a species must match the molar mass used to convert from moles back to grams for that same species.
Verify that the molar mass of is consistently used as across all steps.
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate initial moles of :
Subtract the reacted moles of :
Convert remaining moles to grams:
;
Lock it in
For the reaction , what conversion factor converts moles of into moles of required?
Multiply by . Place the substance you want on top and the substance you are canceling on the bottom.
Similar question
For the reaction , you have and . Identify the limiting reactant and determine how many moles of the excess reactant remain.
Answer
; . Key steps: Needed . Since available , is limiting and remaining .
Consider the synthesis of ammonia: . If () reacts with (), identify the limiting reactant and calculate the mass of excess reactant left unreacted. (Molar mass of , ).
Answer
; . Key steps: Required . Since , is limiting. Unreacted . Mass remaining .
A mixture of () and () undergoes the thermite reaction: . Determine the limiting reactant and the mass in grams of the excess reactant remaining after complete reaction.
Answer
; consumed difference ? Let's calculate: . . Required . Since available , is limiting! Required . Unreacted . Mass of excess . ; .