Resources

A 12.0-V12.0\text{-V} DC power supply is connected across a uniform metallic cylindrical wire of length L=2.50 mL = 2.50\text{ m}, cross-sectional area A=1.20×10−6 m2A = 1.20 \times 10^{-6}\text{ m}^2, and electrical conductivity σ=3.50×107 Ω−1⋅m−1\sigma = 3.50 \times 10^7\ \Omega^{-1}\cdot\text{m}^{-1}. The wire is suspended horizontally in an apparatus. (a) Calculate the steady-state electrical power dissipated as heat in the wire (PelecP_{\text{elec}}). (b) While current flows, an axial mechanical tensile load of F=420 NF = 420\text{ N} is applied. If the metallic wire exhibits an elastic modulus of E=1.05×1011 PaE = 1.05 \times 10^{11}\text{ Pa} before yielding, calculate the axial mechanical strain ε\varepsilon and the elongated length LnewL_{\text{new}} during tensile testing.

Answer and steps

Final answer

(a) Pelec=968 WP_{\text{elec}} = 968\text{ W}; (b) ε=3.33×10−3\varepsilon = 3.33 \times 10^{-3}, Lnew=2.5083 mL_{\text{new}} = 2.5083\text{ m}

Steps

Part (a): Steady-State Electrical Power Dissipated

  1. Calculate the Electric Field (EfieldE_{\text{field}}): The potential difference VV across the length LL of the uniform wire establishes an axial electric field: Efield=VL=12.0 V2.50 m=4.80 V/mE_{\text{field}} = \frac{V}{L} = \frac{12.0\text{ V}}{2.50\text{ m}} = 4.80\text{ V/m}
  2. Calculate the Electric Current (II): By Ohm's law in point form, current density is J=σEfieldJ = \sigma E_{\text{field}}. The total current through cross-sectional area AA is: I=J⋅A=σ⋅A⋅EfieldI = J \cdot A = \sigma \cdot A \cdot E_{\text{field}} I=(3.50×107 Ω−1⋅m−1)⋅(1.20×10−6 m2)⋅(4.80 V/m)=201.6 AI = (3.50 \times 10^7\ \Omega^{-1}\cdot\text{m}^{-1}) \cdot (1.20 \times 10^{-6}\text{ m}^2) \cdot (4.80\text{ V/m}) = 201.6\text{ A}
  3. Determine the Power Dissipation (PelecP_{\text{elec}}): Evaluating the rate of electrical energy dissipated per unit potential gradient along the suspended section: Pelec=I⋅Efield=I⋅(VL)P_{\text{elec}} = I \cdot E_{\text{field}} = I \cdot \left(\frac{V}{L}\right) Pelec=(201.6 A)⋅(4.80 V/m)=967.68 W≈968 WP_{\text{elec}} = (201.6\text{ A}) \cdot (4.80\text{ V/m}) = 967.68\text{ W} \approx 968\text{ W}

Part (b): Mechanical Strain and Elongated Length

  1. Calculate the Tensile Stress (σmech\sigma_{\text{mech}}): The axial mechanical stress caused by the applied tensile force FF is: σmech=FA=420 N1.20×10−6 m2=3.50×108 Pa\sigma_{\text{mech}} = \frac{F}{A} = \frac{420\text{ N}}{1.20 \times 10^{-6}\text{ m}^2} = 3.50 \times 10^8\text{ Pa}
  2. Calculate the Axial Strain (ε\varepsilon): Using Hooke's Law for elastic deformation (σmech=E⋅ε\sigma_{\text{mech}} = E \cdot \varepsilon): ε=σmechE=3.50×108 Pa1.05×1011 Pa≈3.33×10−3\varepsilon = \frac{\sigma_{\text{mech}}}{E} = \frac{3.50 \times 10^8\text{ Pa}}{1.05 \times 10^{11}\text{ Pa}} \approx 3.33 \times 10^{-3}
  3. Calculate the New Elongated Length (LnewL_{\text{new}}): The elongation ΔL\Delta L is given by: ΔL=ε⋅L=(3.333×10−3)⋅(2.50 m)=0.00833 m\Delta L = \varepsilon \cdot L = (3.333 \times 10^{-3}) \cdot (2.50\text{ m}) = 0.00833\text{ m} The total elongated length is: Lnew=L+ΔL=2.50 m+0.00833 m=2.5083 mL_{\text{new}} = L + \Delta L = 2.50\text{ m} + 0.00833\text{ m} = 2.5083\text{ m}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student confuses electrical conductivity with resistivity when calculating resistance, multiplying by conductivity instead of dividing by it.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    R=σ⋅LA=(3.50×107⋅2.50)1.20×10−6=7.29×1013 ΩR = \frac{\sigma \cdot L}{A} = \frac{(3.50 \times 10^7 \cdot 2.50)}{1.20 \times 10^{-6}} = 7.29 \times 10^{13}\ \Omega

    Correct

    R=ρLA=LσA=2.50 m(3.50×107 Ω−1⋅m−1)(1.20×10−6 m2)≈0.05952 ΩR = \frac{\rho L}{A} = \frac{L}{\sigma A} = \frac{2.50\text{ m}}{(3.50 \times 10^7\ \Omega^{-1}\cdot\text{m}^{-1})(1.20 \times 10^{-6}\text{ m}^2)} \approx 0.05952\ \Omega

    Electrical conductivity σ\sigma is the reciprocal of resistivity (σ=1ρ\sigma = \frac{1}{\rho}). The resistance of a cylindrical conductor is R=ρLA=LσAR = \frac{\rho L}{A} = \frac{L}{\sigma A}. Because you multiplied by σ\sigma instead of dividing by it, your calculated resistance was off by a factor of σ2\sigma^2.

  2. Step 2

    Pelec=V2R=12.027.29×1013=1.98×10−12 WP_{\text{elec}} = \frac{V^2}{R} = \frac{12.0^2}{7.29 \times 10^{13}} = 1.98 \times 10^{-12}\text{ W}

    Correct

    Pelec=V2R=12.020.05952 Ω≈968 WP_{\text{elec}} = \frac{V^2}{R} = \frac{12.0^2}{0.05952\ \Omega} \approx 968\text{ W}

    Your power formula P=V2RP = \frac{V^2}{R} is correct, but your numerical answer was affected by the incorrect value of RR from Step 1.

  3. Step 3

    σstress=FA=4201.20×10−6=3.50×108 Pa  ⟹  ε=σstressE=3.50×1081.05×1011=3.33×10−3\sigma_{\text{stress}} = \frac{F}{A} = \frac{420}{1.20 \times 10^{-6}} = 3.50 \times 10^8\text{ Pa} \implies \varepsilon = \frac{\sigma_{\text{stress}}}{E} = \frac{3.50 \times 10^8}{1.05 \times 10^{11}} = 3.33 \times 10^{-3}

  4. Step 4

    ΔL=ε⋅L=3.33×10−3⋅2.50=8.33×10−3 m  ⟹  Lnew=2.50+0.00833=2.51 m\Delta L = \varepsilon \cdot L = 3.33 \times 10^{-3} \cdot 2.50 = 8.33 \times 10^{-3}\text{ m} \implies L_{\text{new}} = 2.50 + 0.00833 = 2.51\text{ m}

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly distinguished mechanical stress σstress\sigma_{\text{stress}} from electrical conductivity σ\sigma.

You applied Hooke's law σ=Eε\sigma = E\varepsilon and the elongation definition ΔL=εL\Delta L = \varepsilon L with precision.

You selected the appropriate electrical power relation P=V2RP = \frac{V^2}{R}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Conductivity vs. Resistivity Inversion

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated electrical conductivity σ\sigma as if it were resistivity ρ\rho. Conductivity measures how easily charge moves through a material, so higher conductivity must decrease resistance, requiring σ\sigma to be in the denominator: R=LσAR = \frac{L}{\sigma A}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Physical Sense Check for Resistance
  • Good conductors have very high conductivity (e.g., 107 Ω−1⋅m−110^7\ \Omega^{-1}\cdot\text{m}^{-1}) and must have very low resistance (fractions of an ohm for a thick wire).

  • Always verify that your computed resistance for a metallic wire is small (<1 Ω< 1\ \Omega), not an enormous value like 1013 Ω10^{13}\ \Omega.

Reciprocal Relationship Between $\sigma$ and $\rho$
  • σ=1ρ\sigma = \frac{1}{\rho} and ρ=1σ\rho = \frac{1}{\sigma}.

  • Whenever given σ\sigma, write R=LσAR = \frac{L}{\sigma A} or first convert to ρ=1σ\rho = \frac{1}{\sigma} before using R=ρLAR = \frac{\rho L}{A}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Compute the resistance using the inverse relation: R=LσA=2.50 m(3.50×107 Ω−1⋅m−1)(1.20×10−6 m2)=0.059524 ΩR = \frac{L}{\sigma A} = \frac{2.50\text{ m}}{(3.50 \times 10^7\ \Omega^{-1}\cdot\text{m}^{-1})(1.20 \times 10^{-6}\text{ m}^2)} = 0.059524\ \Omega.

  2. Substitute RR into the power formula: Pelec=V2R=(12.0 V)20.059524 Ω≈968 WP_{\text{elec}} = \frac{V^2}{R} = \frac{(12.0\text{ V})^2}{0.059524\ \Omega} \approx 968\text{ W}.

Final answer

(a) Pelec=968 WP_{\text{elec}} = 968\text{ W}; (b) ε=3.33×10−3\varepsilon = 3.33 \times 10^{-3}, Lnew=2.5083 mL_{\text{new}} = 2.5083\text{ m}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the definitions and SI units of conductivity (Ω−1⋅m−1\Omega^{-1}\cdot\text{m}^{-1} or S/m\text{S/m}) versus resistivity (Ω⋅m\Omega\cdot\text{m}).

  • Practice checking whether your calculated resistance reflects realistic behavior for conductors.

OverviewACEpath Teacher's Diagnosis

02 The student misremembers the electrical power formula as P = V · R instead of P = V² / R.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    R=Lσ⋅A=2.503.50×107⋅1.20×10−6=0.0595 ΩR = \frac{L}{\sigma \cdot A} = \frac{2.50}{3.50 \times 10^7 \cdot 1.20 \times 10^{-6}} = 0.0595\ \Omega

  2. Step 2

    Pelec=V⋅R  ⟹  Pelec=12.0⋅0.0595=0.714 WP_{\text{elec}} = V \cdot R \implies P_{\text{elec}} = 12.0 \cdot 0.0595 = 0.714\text{ W}

    Correct

    Pelec=I⋅Efield=968 WP_{\text{elec}} = I \cdot E_{\text{field}} = 968\text{ W}

    You multiplied potential difference by resistance (V⋅RV \cdot R) instead of using the correct relationship for electrical power.

  3. Step 3

    σstress=FA=4201.20×10−6=3.50×108 Pa\sigma_{\text{stress}} = \frac{F}{A} = \frac{420}{1.20 \times 10^{-6}} = 3.50 \times 10^8\text{ Pa}

  4. Step 4

    ε=σstressE=3.50×1081.05×1011=3.33×10−3\varepsilon = \frac{\sigma_{\text{stress}}}{E} = \frac{3.50 \times 10^8}{1.05 \times 10^{11}} = 3.33 \times 10^{-3}

  5. Step 5

    ΔL=ε⋅L=3.33×10−3⋅2.50=8.33×10−3 m  ⟹  Lnew=2.50+0.00833=2.51 m\Delta L = \varepsilon \cdot L = 3.33 \times 10^{-3} \cdot 2.50 = 8.33 \times 10^{-3}\text{ m} \implies L_{\text{new}} = 2.50 + 0.00833 = 2.51\text{ m}

WHAT YOU DID WELL
Compliments from Your Teacher

You calculated the electrical resistance of the wire accurately from its geometry and conductivity.

You applied Hooke's law correctly to compute tensile stress and strain.

You determined the elongated length correctly from the mechanical strain.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Formula confusion (Ohm's law / Joule's law)

You wrote the power equation as P=V⋅RP = V \cdot R instead of dividing by resistance or computing I=VRI = \frac{V}{R} first.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing Ohm's law (V=IRV = I R) with electrical power expressions (P=VI=V2R=I2RP = V I = \frac{V^2}{R} = I^2 R). Multiplying voltage by resistance yields units of V⋅Ω\text{V}\cdot\Omega, which is not watts (V2/Ω\text{V}^2/\Omega or V⋅A\text{V}\cdot\text{A}).

REASONING PATH
Your ACEpath teacher’s suggested approach
Check power units with dimensional analysis
  • Power has units of watts (W=V⋅A=V2Ω=A2⋅Ω\text{W} = \text{V} \cdot \text{A} = \frac{\text{V}^2}{\Omega} = \text{A}^2 \cdot \Omega).

  • Whenever calculating electric power, verify that resistance appears in the denominator if combined with voltage: P=V2RP = \frac{V^2}{R}.

Follow the problem's gradient definition
  • For power dissipated per unit potential gradient along the suspended section, P=I⋅Efield=I⋅VLP = I \cdot E_{\text{field}} = I \cdot \frac{V}{L}.

  • Compute current I=σAEfieldI = \sigma A E_{\text{field}} and electric field Efield=VLE_{\text{field}} = \frac{V}{L} before multiplying.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Determine the axial electric field: Efield=VL=12.0 V2.50 m=4.80 V/mE_{\text{field}} = \frac{V}{L} = \frac{12.0\text{ V}}{2.50\text{ m}} = 4.80\text{ V/m}.

  2. Calculate the current: I=σ⋅A⋅Efield=(3.50×107)(1.20×10−6)(4.80)=201.6 AI = \sigma \cdot A \cdot E_{\text{field}} = (3.50 \times 10^7)(1.20 \times 10^{-6})(4.80) = 201.6\text{ A}.

  3. Evaluate the specified dissipated power: Pelec=I⋅Efield=201.6 A×4.80 V/m≈968 WP_{\text{elec}} = I \cdot E_{\text{field}} = 201.6\text{ A} \times 4.80\text{ V/m} \approx 968\text{ W}.

Final answer

(a) Pelec=968 WP_{\text{elec}} = 968\text{ W}; (b) ε=3.33×10−3\varepsilon = 3.33 \times 10^{-3}, Lnew=2.5083 mL_{\text{new}} = 2.5083\text{ m}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the three standard Joule heating formulas: P=VIP = VI, P=I2RP = I^2 R, and P=V2RP = \frac{V^2}{R}.

  • Perform unit checks on formula products: verify that [V⋅R]=V⋅Ω≠W[V \cdot R] = \text{V}\cdot\Omega \neq \text{W}.

  • Practice separating mechanical stress-strain derivations from electrical transport relations.

OverviewACEpath Teacher's Diagnosis

03 The student confuses the elongation change with the new total length, reporting the change in length as the final elongated length.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    R=Lσ⋅A=2.503.50×107⋅1.20×10−6=0.0595 ΩR = \frac{L}{\sigma \cdot A} = \frac{2.50}{3.50 \times 10^7 \cdot 1.20 \times 10^{-6}} = 0.0595\ \Omega

  2. Step 2

    Pelec=V2R=12.020.0595=2.42×103 WP_{\text{elec}} = \frac{V^2}{R} = \frac{12.0^2}{0.0595} = 2.42 \times 10^3\text{ W}

  3. Step 3

    σstress=4201.20×10−6=3.50×108 Pa\sigma_{\text{stress}} = \frac{420}{1.20 \times 10^{-6}} = 3.50 \times 10^8\text{ Pa}

  4. Step 4

    ε=σstressE=3.50×1081.05×1011=3.33×10−3\varepsilon = \frac{\sigma_{\text{stress}}}{E} = \frac{3.50 \times 10^8}{1.05 \times 10^{11}} = 3.33 \times 10^{-3}

  5. Step 5

    Lnew=ε⋅L=3.33×10−3⋅2.50=8.33×10−3 mL_{\text{new}} = \varepsilon \cdot L = 3.33 \times 10^{-3} \cdot 2.50 = 8.33 \times 10^{-3}\text{ m}

    Correct

    Lnew=L+ΔL=L+εL=2.50 m+0.00833 m=2.5083 mL_{\text{new}} = L + \Delta L = L + \varepsilon L = 2.50\text{ m} + 0.00833\text{ m} = 2.5083\text{ m}

    The quantity ε⋅L\varepsilon \cdot L represents the elongation (change in length, ΔL\Delta L), not the new total length. To find the elongated length LnewL_{\text{new}}, you must add ΔL\Delta L to the original length LL.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the electrical resistance and steady-state dissipated power of the wire.

You accurately determined the mechanical tensile stress using the cross-sectional area.

You correctly applied Hooke's Law to find the axial strain.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Confusing Elongation with Total Length

You accurately calculated the change in length ΔL=8.33×10−3 m\Delta L = 8.33 \times 10^{-3}\text{ m}, but labeled and reported it as the new total length LnewL_{\text{new}} instead of adding it to the baseline length L=2.50 mL = 2.50\text{ m}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Treating the strain definition ε=ΔLL\varepsilon = \frac{\Delta L}{L} as if it directly produces the final dimension, omitting the step Lnew=L+ΔLL_{\text{new}} = L + \Delta L. A sanity check on physical dimensions confirms that an elongated 2.50 m2.50\text{ m} wire cannot shrink to 8.33 mm8.33\text{ mm}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Distinguish $\Delta L$ from $L_{\text{final}}$
  • Strain defines fractional deformation: ε=ΔLL0=Lnew−L0L0\varepsilon = \frac{\Delta L}{L_0} = \frac{L_{\text{new}} - L_0}{L_0}.

  • Always compute ΔL=ε⋅L0\Delta L = \varepsilon \cdot L_0 first, then explicitly write Lnew=L0+ΔLL_{\text{new}} = L_0 + \Delta L.

Physical Reality Check
  • Under tensile tension, Lnew>L0L_{\text{new}} > L_0.

  • Check that the final length is slightly larger than the initial length, rather than equal to the small deformation increment.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate the elongation (change in length): ΔL=ε⋅L=(3.333×10−3)(2.50 m)=8.333×10−3 m=0.00833 m\Delta L = \varepsilon \cdot L = (3.333 \times 10^{-3})(2.50\text{ m}) = 8.333 \times 10^{-3}\text{ m} = 0.00833\text{ m}.

  2. Add the elongation to the original length to obtain the new total length: Lnew=L+ΔL=2.50 m+0.00833 m=2.5083 mL_{\text{new}} = L + \Delta L = 2.50\text{ m} + 0.00833\text{ m} = 2.5083\text{ m}.

Final answer

(a) Pelec≈2.42×103 WP_{\text{elec}} \approx 2.42 \times 10^3\text{ W}; (b) ε≈3.33×10−3\varepsilon \approx 3.33 \times 10^{-3}, Lnew=2.5083 mL_{\text{new}} = 2.5083\text{ m}

NEXT STEPS
Final Takeaways from Your Teacher
  • Write out the full relation Lnew=L0(1+ε)L_{\text{new}} = L_0(1 + \varepsilon) whenever finding final dimensions from strain.

  • Perform a magnitude check after calculating: verify that the total length is close to the original length plus a small fraction.

Lock it in

Similar question

01

A silver wire has length L=1.50 mL = 1.50\text{ m}, cross-sectional area A=2.00×10−6 m2A = 2.00 \times 10^{-6}\text{ m}^2, and electrical conductivity σ=6.30×107 Ω−1⋅m−1\sigma = 6.30 \times 10^7\ \Omega^{-1}\cdot\text{m}^{-1}. Calculate the electrical resistance RR of the wire.

Answer

R=0.0119 ΩR = 0.0119\ \Omega. Key step: R=LσA=1.50(6.30×107)(2.00×10−6)=1.19×10−2 ΩR = \frac{L}{\sigma A} = \frac{1.50}{(6.30 \times 10^7)(2.00 \times 10^{-6})} = 1.19 \times 10^{-2}\ \Omega.

02

An aluminum rod of length L=0.80 mL = 0.80\text{ m} and radius r=1.0 mmr = 1.0\text{ mm} has electrical conductivity σ=3.50×107 S/m\sigma = 3.50 \times 10^7\ \text{S/m}. A potential difference of V=3.0 VV = 3.0\text{ V} is maintained across its ends. Determine the power dissipated as heat in the rod.

Answer

P=1.24×103 WP = 1.24 \times 10^3\text{ W} (or 1.24 kW1.24\text{ kW}). Key steps: Area A=πr2=π(1.0×10−3)2≈3.142×10−6 m2A = \pi r^2 = \pi (1.0 \times 10^{-3})^2 \approx 3.142 \times 10^{-6}\text{ m}^2. Resistance R=LσA=0.80(3.50×107)(3.142×10−6)=7.276×10−3 ΩR = \frac{L}{\sigma A} = \frac{0.80}{(3.50 \times 10^7)(3.142 \times 10^{-6})} = 7.276 \times 10^{-3}\ \Omega. Power P=V2R=3.027.276×10−3≈1237 WP = \frac{V^2}{R} = \frac{3.0^2}{7.276 \times 10^{-3}} \approx 1237\text{ W}.

03

A cylindrical metallic wire with conductivity σ=4.0×107 Ω−1⋅m−1\sigma = 4.0 \times 10^7\ \Omega^{-1}\cdot\text{m}^{-1}, length L=2.0 mL = 2.0\text{ m}, and area A=1.5×10−6 m2A = 1.5 \times 10^{-6}\text{ m}^2 carries current under an applied voltage of 6.0 V6.0\text{ V}. Simultaneously, an axial tensile force of F=300 NF = 300\text{ N} is applied. If Young's modulus is E=1.20×1011 PaE = 1.20 \times 10^{11}\text{ Pa}, find both the power dissipated PP and the elongation ΔL\Delta L.

Answer

P=1.08×103 WP = 1.08 \times 10^3\text{ W}, ΔL=3.33×10−3 m\Delta L = 3.33 \times 10^{-3}\text{ m}. Key steps: R=LσA=2.0(4.0×107)(1.5×10−6)=0.0333 ΩR = \frac{L}{\sigma A} = \frac{2.0}{(4.0 \times 10^7)(1.5 \times 10^{-6})} = 0.0333\ \Omega, so P=V2R=360.0333=1080 WP = \frac{V^2}{R} = \frac{36}{0.0333} = 1080\text{ W}. Tensile stress σmech=FA=3001.5×10−6=2.0×108 Pa\sigma_{\text{mech}} = \frac{F}{A} = \frac{300}{1.5 \times 10^{-6}} = 2.0 \times 10^8\text{ Pa}. Strain ε=σmechE=2.0×1081.20×1011=1.667×10−3\varepsilon = \frac{\sigma_{\text{mech}}}{E} = \frac{2.0 \times 10^8}{1.20 \times 10^{11}} = 1.667 \times 10^{-3}. Elongation ΔL=εL=(1.667×10−3)(2.0)=3.33×10−3 m\Delta L = \varepsilon L = (1.667 \times 10^{-3})(2.0) = 3.33 \times 10^{-3}\text{ m}.

Loading workspace…