Resources
A cryogenic container holds of liquid nitrogen at its normal boiling point of (). An imperfect vacuum seal allows heat to leak into the container at a steady rate of (). Determine the critical threshold of time, in minutes, before the liquid nitrogen is entirely boiled away.
Answer and steps
Final answer
Steps
Calculate the total heat required for vaporization ()
To find the time required for all the liquid nitrogen to boil off, we determine the total heat energy needed for the phase change and divide it by the rate at which heat enters the system.
Since the liquid nitrogen is already at its boiling point (), no energy is needed to change its temperature. The heat required strictly goes into the phase transition from liquid to gas:
Substitute the given mass and heat of vaporization:
Calculate the time in seconds ()
The power represents the rate of heat transfer per unit time:
Given that , the rate of heat leak is :
Convert the time into minutes
Convert the time from seconds to minutes:
Rounding to three significant figures to match the given data (, , and ):
Common Pitfall: Ensure that the rate of heat transfer is kept in compatible units (watts correspond to joules per second, not minutes), so always calculate time in seconds first before converting to minutes.
Typical errors
01 The student calculates the time in seconds but forgets to convert the final answer to minutes as requested by the problem.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
The prompt specifically asked for the critical time in minutes, not seconds. Dividing by yields approximately .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly used to find the total thermal energy needed to vaporize the liquid nitrogen.
You correctly interpreted and used to solve for time in seconds.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou solved for time in seconds using the definition of a watt, but overlooked the prompt's explicit request for the final answer in minutes.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisBecause power in watts () inherently outputs time in SI base units (seconds), the calculation naturally terminates in seconds unless an explicit final unit-conversion checkpoint is performed.
REASONING PATH
Your ACEpath teacher’s suggested approach- Match prompt units
Always circle or highlight the requested unit in the prompt before starting calculations.
Check the final calculated quantity against the requested unit; if the prompt asks for minutes and your formula yields seconds, divide by .
CORRECTED PATH
ACEpath Teacher's DemonstrationConvert seconds to minutes:
Round to three significant figures to match the given data (, , ):
02 The student multiplies by 60 instead of dividing by 60 when converting seconds to minutes.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
You multiplied by instead of dividing by . Since , converting from a smaller unit (seconds) to a larger unit (minutes) requires multiplying by so that seconds cancel out.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the latent heat of vaporization .
You used the definition of power correctly to find time in seconds.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou inverted the conversion factor ratio when changing units from seconds to minutes.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou did not set up dimensional analysis to cancel units algebraically, leading you to multiply by instead of dividing by .
REASONING PATH
Your ACEpath teacher’s suggested approach- Dimensional Analysis Cancellation
Set up unit factors so the unit you want to eliminate appears in the denominator: .
Always write out the units in fraction form and cancel them before multiplying or dividing the numbers.
CORRECTED PATH
ACEpath Teacher's DemonstrationMultiply by the conversion factor :
Round to three significant figures to match the given values (, , and ):
03 The student misapplies the relationship between power, energy, and time by multiplying power by heat instead of dividing.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
Because power is the rate of energy transfer (), solving for time requires dividing heat by power (), rather than multiplying them.
- Step 3Correct
Your conversion method from seconds to minutes by dividing by is correct, but the numerical result is affected by the error in the previous step.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the total latent heat required to boil off the liquid nitrogen.
You correctly converted time in seconds to minutes using the conversion factor of .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou set up instead of rearranging to .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou conflated the relationship between power, energy, and time, treating power as a multiplier rather than a rate ().
REASONING PATH
Your ACEpath teacher’s suggested approach- Define Power as a Rate
Power equals energy per unit time: .
Always isolate time algebraically as before plugging in numbers.
- Dimensional Analysis Check
Multiplying yields , not seconds.
Check units during algebraic rearrangement: .
CORRECTED PATH
ACEpath Teacher's DemonstrationUse the definition of power: .
Substitute the heat and power values: .
Convert seconds to minutes: .
Round to three significant figures: .
Lock it in
When using power with in watts () and heat in joules (), what unit does the resulting time have?
Seconds (), because . You must explicitly convert to minutes or hours if requested.
Similar question
A sample of liquid argon is at its boiling point (). Heat enters the insulated flask at a constant rate of . Calculate the time, in minutes, required for the sample to completely vaporize.
Answer
. Time in seconds: . Convert to minutes: .
An ice bath contains of ice at (). An electric immersion heater delivers heat at . How many minutes will it take to melt all the ice?
Answer
. Time in seconds: . Convert to minutes: .
A dewar flask holds of liquid helium at its boiling point of (). If heat leaks in at , determine the time, in hours, required for the helium to boil away completely.
Answer
. Time in seconds: . Convert to hours: .