Resources
A sample of solid calcium carbonate (, molar mass ) undergoes complete thermal decomposition according to the reaction . The evolved carbon dioxide gas is collected over water in an inverted graduated cylinder at an ambient barometric pressure of and a water-bath temperature of , occupying a measured gas volume of . Given that the equilibrium vapor pressure of water at is , combine Dalton's law of partial pressures with stoichiometric relations to determine the initial mass of in grams (). Use and .
Answer and steps
Final answer
Steps
Find the partial pressure of dry
To determine the initial mass of , we determine the moles of dry gas collected using Dalton's law of partial pressures and the ideal gas law, and then apply stoichiometry.
When a gas is collected over water, the total pressure inside the collection vessel is the sum of the partial pressure of the gas and the equilibrium vapor pressure of water at that temperature (Dalton's law):
Subtract the vapor pressure of water from the total atmospheric pressure:
Convert this pressure into atmospheres:
Common Pitfall: Forgetting to subtract the vapor pressure of water will overestimate the pressure—and thus the moles and mass—of the product gas.
Convert units and calculate moles of
Convert the volume to liters and temperature to kelvins:
Using the ideal gas law, :
Substitute the values:
Relate moles of to the initial mass of
From the balanced chemical equation:
The stoichiometric ratio between and is . Therefore:
Multiply by the molar mass of ():
Typical errors
01 The student ignores the vapor pressure of water when gas is collected over water, using the total barometric pressure directly as the pressure of carbon dioxide.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
When gas is collected over water, the gas inside the cylinder is saturated with water vapor. According to Dalton's law of partial pressures, you must subtract the vapor pressure of water () from the barometric pressure () to find the partial pressure of dry .
- Step 2Correct
You set up and evaluated the ideal gas law calculation correctly, but the result is affected by the uncorrected pressure value from the previous step.
- Step 3Correct
Your stoichiometric mole ratio and molar mass multiplication were completely correct, but the final numerical mass inherited the earlier pressure error.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly converted the gas volume from milliliters to liters.
You correctly converted the water bath temperature to kelvins.
You applied the ideal gas equation accurately with consistent units.
You used the correct stoichiometric mole ratio between and .
You accurately multiplied by the molar mass to obtain the mass in grams.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated the total barometric pressure inside the collection vessel as solely due to dry , overlooking that gas collected over water is a mixture containing water vapor whose equilibrium vapor pressure must be deducted via Dalton's law.
REASONING PATH
Your ACEpath teacher’s suggested approach- Gas Collection Over Water
Whenever a problem mentions that a gas is 'collected over water', immediately isolate before converting to atmospheres or plugging into .
CORRECTED PATH
ACEpath Teacher's DemonstrationSubtract the equilibrium vapor pressure of water from the barometric pressure: .
Convert the partial pressure of dry to atmospheres: .
Calculate the moles of dry using : .
Relate moles of to via stoichiometry and calculate the mass: .
02 The student fails to convert the temperature from Celsius to Kelvin, using 24.0 directly in the ideal gas equation.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You used directly in the denominator without converting from degrees Celsius to Kelvin. Because the ideal gas constant is defined using Kelvin, gas law calculations require absolute temperature ().
- Step 3Correct
Your stoichiometric ratio and multiplication by molar mass are mathematically valid, but the value is inflated due to using the uncorrected mole quantity from Step 2.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly applied Dalton's law of partial pressures to subtract the vapor pressure of water from the total atmospheric pressure.
You accurately converted the dry gas pressure from torr to atmospheres and the volume from milliliters to liters.
You correctly identified the stoichiometric molar ratio between and and applied the correct molar mass.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou entered the temperature value of directly into the denominator of .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisGas laws relate physical quantities to absolute kinetic temperature, where zero corresponds to absolute zero (), not the Celsius freezing point of water. The units of the gas constant () require to be in Kelvin to cancel units properly.
REASONING PATH
Your ACEpath teacher’s suggested approach- Temperature Unit Verification
All ideal gas law calculations () require temperature on the thermodynamic absolute scale: T\text{ (K)} = T\text{ ({}^\circ$$\text{C}$$)} + 273.15.
Before substituting into , always write out and check that temperature units cancel with .
CORRECTED PATH
ACEpath Teacher's DemonstrationConvert the temperature to Kelvin: .
Recalculate the moles of evolved : .
Apply the mole ratio and molar mass: .
03 The student adds the vapor pressure of water to the total atmospheric pressure instead of subtracting it to find the partial pressure of CO2.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
When gas is collected over water, the total measured pressure is the sum of the dry gas pressure and the water vapor pressure (). Therefore, you must subtract from to find .
- Step 2Correct
You correctly converted the volume and temperature and applied the ideal gas equation , but the resulting mole value is affected by the incorrect pressure from Step 1.
- Step 3Correct
You correctly used the stoichiometric molar ratio and multiplied by the molar mass of , but the final mass is slightly too high due to the earlier pressure error.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly converted the gas volume from milliliters to liters ().
You accurately converted Celsius temperature to Kelvin ().
You correctly set up and solved the ideal gas law .
You applied the proper stoichiometric ratio and molar mass to determine the solid reactant mass.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou wrote instead of .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisMisinterpreting Dalton's law of partial pressures for gases collected over water: the measured total pressure inside the container includes both the target dry gas and the evaporated water vapor, so the target gas makes up only a fraction of the total pressure.
REASONING PATH
Your ACEpath teacher’s suggested approach- Collection Over Water Rule
Always isolate the dry gas by subtraction: .
- Reasonableness Check
A component partial pressure cannot exceed total mixture pressure.
Verify that your calculated dry gas pressure is strictly less than the barometric pressure.
CORRECTED PATH
ACEpath Teacher's DemonstrationLock it in
What does Dalton's law state about the pressure of a gas collected over water?
, so . Water vapor always contributes to the total collected pressure.
Similar question
A sample of hydrogen gas is collected over water at and an atmospheric pressure of . The vapor pressure of water at is . If the volume of the gas mixture is , calculate the moles of dry collected. ()
Answer
. Key steps: ; ; ; .
Solid potassium chlorate decomposes according to . The oxygen produced is collected over water at () and total pressure, occupying . Find the mass of (molar mass ) decomposed.
Answer
. Key steps: ; ; ; .
A alloy sample containing zinc reacts with excess according to . The generated is collected over water at () and a barometric pressure of , giving a volume of . Determine the mass percent of zinc (molar mass ) in the alloy.
Answer
. Key steps: ; ; ; ; ; .