Resources
A soil geochemical study measures the composition of lead isotopes in a contaminated mineral sample. The sample contains two primary lead isotopes: with an isotopic mass of at a mass concentration of , and with an isotopic mass of at a mass concentration of . Assuming these two isotopes account for the entire lead content, convert the concentration data into isotopic atom abundances and calculate the sample's average atomic mass of lead to five significant figures.
Answer and steps
Final answer
Steps
Understand the Distinction Between Mass Fraction and Atom Abundance
To find the average atomic mass of lead in the mineral sample, we must first convert the given mass concentrations into isotopic atom abundances (mole fractions), and then calculate the weighted average atomic mass.
The sample data provides mass concentrations:
- Mass of per gram of total lead
- Mass of per gram of total lead
Because atoms are slightly heavier than atoms, equal masses do not contain equal numbers of atoms. Average atomic mass is defined on a per-atom basis, so we must calculate the relative number of moles (or atoms) of each isotope.
Calculate the Relative Number of Moles
Using the isotopic masses:
- (or )
- (or )
Divide the mass of each isotope by its isotopic mass to find the relative molar amount:
The total molar amount of lead is:
Determine the Isotopic Atom Abundances
The atom abundance (mole fraction, ) of each isotope is the ratio of its moles to the total moles:
Calculate the Average Atomic Mass
The average atomic mass () is the abundance-weighted average of the isotopic masses:
Substituting the values:
Rounded to five significant figures, the average atomic mass of lead in the sample is .
Typical errors
01 The student treats the given mass concentrations directly as atom abundances without converting to molar quantities, leading to an incorrect average atomic mass.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You calculated the mass fractions rather than the isotopic atom abundances. Because isotopes have different masses per atom, equal masses do not contain equal numbers of atoms. You must divide each mass by its isotopic mass to find moles before calculating the fractional abundance.
- Step 2Correct
You applied the weighted sum correctly, but this step is affected by substituting the mass fractions from Step 1 instead of the true atom abundances.
WHAT YOU DID WELL
Compliments from Your TeacherYou summed the component quantities to find the total baseline.
You correctly applied the weighted average structure to find average atomic mass.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou conflated mass fraction with atom abundance (mole fraction), overlooking that average atomic mass is defined on a per-atom basis and therefore requires isotopic amounts in moles.
REASONING PATH
Your ACEpath teacher’s suggested approach- Check the given abundance type
Average atomic mass weighting requires atom abundance (mole fraction), not mass percent or mass fraction.
Whenever concentration or mass data is provided, divide each component mass by its isotopic mass to determine relative moles before finding fractional abundance.
CORRECTED PATH
ACEpath Teacher's DemonstrationConvert each mass into relative molar amounts: and .
Find total moles: .
Compute atom abundances: and .
Calculate weighted average: .
02 The student divides the isotopic masses by the mass concentrations instead of dividing mass concentrations by isotopic masses to find moles.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
To convert mass into amount of substance (moles), you must divide mass by molar mass (). You placed the isotopic mass in the numerator and the mass concentration in the denominator, which calculates rather than moles.
- Step 2Correct
Your method of dividing individual moles by total moles to find atom abundances (mole fractions) is correct, but the values are inverted because of the error in Step 1.
- Step 3Correct
You correctly weighted the isotopic masses by your calculated fractional abundances, but the inverted abundances shifted the weighted average toward the heavier isotope.
WHAT YOU DID WELL
Compliments from Your TeacherYou recognized that mass concentrations must be converted to mole fractions before calculating average atomic mass.
You correctly defined the atom abundance as the ratio of an isotope's moles to the total moles.
You correctly applied the weighted-average formula using fractional abundances and isotopic masses.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou divided molar mass by mass instead of dividing mass by molar mass when finding relative moles.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusion between the formula and its reciprocal, likely caused by not tracking dimensional units like and during the division.
REASONING PATH
Your ACEpath teacher’s suggested approach- Dimensional Analysis for Moles
Amount of substance in moles equals mass divided by molar mass: (with units ).
Always write the units explicitly in the fraction to ensure the mass units cancel and moles remain in the numerator.
- Sanity Check on Abundances
A lighter isotope has more atoms per gram than a heavier isotope.
If the lighter isotope has a higher mass concentration (), its atom fraction must be even higher than its mass fraction ().
CORRECTED PATH
ACEpath Teacher's Demonstrationand
and
03 The student calculates the unweighted simple arithmetic average of the isotopic masses, completely ignoring the isotopic abundance data.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
You calculated a simple arithmetic mean of the two isotopic masses by dividing their sum by , which assumes a split. You need to multiply each isotopic mass by its corresponding atom abundance () that you found in Step 2.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly recognized that mass concentrations must be converted to molar amounts before finding atom abundances.
You accurately calculated the mole fractions of and .
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou forgot to apply the calculated atom abundances as weights in the average atomic mass formula, defaulting instead to a simple arithmetic mean .
REASONING PATH
Your ACEpath teacher’s suggested approach- Weighted Average Formula
Average atomic mass is the abundance-weighted sum: , where is the fractional atom abundance of isotope .
Always multiply each isotope's mass by its fractional abundance () and sum the products, rather than adding the masses and dividing by the number of isotopes.
CORRECTED PATH
ACEpath Teacher's DemonstrationMultiply each isotopic mass by its corresponding atom fraction:
Sum the weighted contributions:
Round to five significant figures:
Lock it in
What is the difference between isotopic mass fraction and isotopic atom abundance?
Mass fraction is the ratio of an isotope's mass to total mass. Atom abundance (mole fraction) is the ratio of an isotope's number of atoms (moles) to total atoms. Average atomic mass requires atom abundance.
Similar question
A sample of neon contains () and () with mass concentrations of and , respectively. Determine the isotopic atom abundance of to four significant figures.
Answer
(or ). Key steps: , , , .
A synthetic mixture of chlorine consists of () and () with a mass ratio of . Calculate the average atomic mass of chlorine in this sample to four significant figures.
Answer
. Key steps: For of and of , , . , . Average atomic mass .
An enriched lithium target has a () mass fraction of and a () mass fraction of . Calculate both the atom abundance of and the average atomic mass of lithium in the target to four significant figures.
Answer
Atom abundance of (); average atomic mass . Key steps: Moles per : , , . . Average mass .