Resources
A chemist assesses a fluorinated solvent whose vapor pressure at is recorded as and whose standard enthalpy of vaporization is given in imperial engineering units as (where and ). The molar mass of the compound is . Convert all parameters into consistent SI units and use to determine the boiling point of the solvent in under a local atmospheric pressure of ().
Answer and steps
Final answer
Steps
Convert all parameters into consistent SI units
Method: Clausius-Clapeyron Relation
The boiling point of a liquid at a given external pressure is the temperature at which its equilibrium vapor pressure equals the atmospheric pressure. The relationship between vapor pressure and temperature is modeled by the integrated Clausius-Clapeyron equation:
-
Initial state :
- Final state pressure : At the boiling point, the vapor pressure equals the local atmospheric pressure:
- Pressure ratio:
-
Molar enthalpy of vaporization (): Convert from imperial engineering units () to molar SI units ():
- Specific enthalpy per gram:
- Molar enthalpy of vaporization:
Solve for the boiling temperature ()
Rearrange the Clausius-Clapeyron equation to isolate :
Substitute the values:
- Evaluating the temperature shift accounting for the solvent phase transition parameters yields:
Convert the boiling point to degrees Celsius
Pitfall to Avoid
- Unit Mismatch in and : Ensure is converted to rather than or , because the ideal gas constant contains moles and joules in its unit base.
Typical errors
01 The student forgets to multiply the specific enthalpy of vaporization by the molar mass, using J/g instead of J/mol in the Clausius-Clapeyron equation.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
Your conversion converted to , not . Because the gas constant uses moles, you must multiply this specific enthalpy by the molar mass () to find the molar enthalpy of vaporization.
- Step 3Correct
Your algebraic isolation of followed correctly from your values, but substituting the undersized caused to be about two orders of magnitude too large, resulting in a negative value for .
- Step 4Correct
This result was directly thrown off by the earlier enthalpy unit error. An absolute temperature in Kelvin can never be negative, which is a clear diagnostic signal to re-check enthalpy units.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified and applied the integrated Clausius-Clapeyron equation.
You accurately converted the pressures from kilopascals and torr to pascals.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated specific enthalpy (energy per unit mass, ) as molar enthalpy (energy per mole, ) without multiplying by the molar mass (). Because is expressed in , dimensional consistency requires to be in .
REASONING PATH
Your ACEpath teacher’s suggested approach- Dimensional Alignment with Gas Constant R
The universal gas constant contains moles in the denominator, requiring all extensive enthalpy quantities in thermodynamic equations like Clausius-Clapeyron to be molar quantities ().
Always write out dimensional analysis explicitly: .
- Sanity Check on Thermodynamic Outputs
Absolute temperature in Kelvin () must always be strictly positive (), and increasing the vapor pressure of a liquid must always require an increase in temperature.
If your calculated temperature turns out negative or substantially lower than the initial temperature despite pressure increasing, stop and check the unit scale of .
CORRECTED PATH
ACEpath Teacher's DemonstrationCompute the molar enthalpy of vaporization: .
Calculate the pressure ratio and its natural logarithm: .
Solve for the reciprocal boiling point using Clausius-Clapeyron: .
Convert to Kelvin and degrees Celsius: .
02 The student drops the negative sign in the integrated Clausius-Clapeyron equation, causing the calculated boiling temperature to be erroneously lower than the initial temperature despite the increase in vapor pressure.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You omitted the negative sign in front of . Because vaporization is endothermic (), vapor pressure increases with temperature; omitting the negative sign reverses the temperature trend.
- Step 3Correct
Your algebra follows consistently from your written equation, but the sign error from Step 2 propagated here, producing an unphysical temperature decrease.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly converted the pressure from torr to pascals.
You correctly converted the specific enthalpy from imperial engineering units into molar SI units ().
You carried out the subsequent algebraic isolation and unit conversion from Kelvin to Celsius accurately.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou omitted the negative sign (or swapped the order of temperatures) in the integrated form . A helpful physical sanity check is that higher vapor pressure always corresponds to a higher temperature.
REASONING PATH
Your ACEpath teacher’s suggested approach- Integrated Clausius-Clapeyron Sign Convention
When using a positive prefactor, ensure the temperature term is ordered as . Check that if , then .
CORRECTED PATH
ACEpath Teacher's DemonstrationWrite the correctly signed Clausius-Clapeyron equation: .
Substitute the values: .
Divide by : .
Solve for : .
Convert to Celsius: .
03 The student reports the final boiling point in Kelvin rather than converting the result to degrees Celsius as required by the problem.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3
- Step 4Correct
You found the absolute temperature in Kelvin, but the question explicitly asked for the boiling point in .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly converted the pressure values and enthalpy of vaporization into consistent SI units.
You correctly formulated and manipulated the integrated Clausius-Clapeyron equation to solve for the boiling temperature in Kelvin.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou stopped your calculation upon finding the absolute temperature in Kelvin, omitting the final conversion step to degrees Celsius.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated finding the thermodynamic variable as the completion of the problem, overlooking the specific unit requirement () stated in the prompt.
REASONING PATH
Your ACEpath teacher’s suggested approach- Verify final requested units
Thermodynamic state equations inherently compute temperatures on the absolute scale (), but chemistry and engineering problems frequently request the result in degrees Celsius ().
Always re-read the prompt's final sentence to check the requested unit and apply whenever required.
CORRECTED PATH
ACEpath Teacher's DemonstrationTake your calculated boiling temperature in Kelvin: .
Subtract to convert to degrees Celsius: .
Lock it in
Why must have units of rather than when using the Clausius-Clapeyron equation with ?
Because the denominator contains , which is per mole. Moles in must cancel the moles in to produce a reciprocal temperature unit ().
Similar question
A substance with a molar mass of has a specific heat of vaporization of . What is its molar heat of vaporization in ?
Answer
. Multiply specific enthalpy by molar mass: (or ).
Acetone () has a normal boiling point of () at . Its molar enthalpy of vaporization is . Find its vapor pressure at () using .
Answer
. Convert . Using : . Thus .
An unknown volatile liquid boiling at at has a recorded specific enthalpy of vaporization of . At , its vapor pressure drops to . Calculate the molar mass of this liquid.
Answer
. First solve for molar enthalpy: . Then .