Resources
A specialty polymer reaction operates with an Environmental Factor () of . In an industrial pilot run designed to produce a target resin, a total waste output of was collected and documented. If the overall chemical reaction that synthesizes this resin has a theoretical maximum yield of from the input raw materials, reverse engineer the process data to calculate: (a) the actual mass of polymer resin successfully isolated in kilograms, and (b) the actual percentage yield of the pilot reaction.
Answer and steps
Final answer
(a) ; (b)
Steps
Part (a): Calculate the Mass of Isolated Product
The Environmental Factor () is a green chemistry metric defined by Roger Sheldon to evaluate the mass of waste generated per unit mass of desired product:
Rearranging this formula to solve for the actual mass of the isolated polymer resin gives:
Substitute the given values into the equation:
Part (b): Calculate the Percentage Yield
The percentage yield compares the actual mass of product isolated from the reaction to the theoretical maximum mass predicted by stoichiometry:
Using the actual yield of obtained in Part (a) and the given theoretical yield of :
Rounding to two decimal places gives:
Common Pitfall to Avoid
- Denominator confusion: Do not confuse the denominator of the equation (which is strictly the actual mass of isolated product) with the total mass of raw materials or the theoretical yield. Using the theoretical yield in the formula would underestimate the true waste-to-product ratio of the practical process.
Typical errors
01 The student inverts the E-factor definition as product mass divided by waste mass, leading to an extremely high calculated mass of product.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
E = = E = 4.85 1479.25 = 7174.36
CorrectE = = = = 305.00
The Environmental Factor () measures the mass of waste produced per unit mass of desired product, meaning . By writing the reciprocal ratio, you multiplied by the waste mass instead of dividing by the , resulting in an erroneously high isolated mass.
- Step 2
= 100% = 100% = 1887.99%
Correct= 100% = 80.26%
You applied the correct percentage yield formula, but substituting the incorrect actual mass of from part (a) led to a percentage yield well over , which is physically impossible for an isolated reaction product.
WHAT YOU DID WELL
Compliments from Your TeacherYou stated and applied the correct general formula for percentage yield.
You performed accurate algebraic rearrangements and arithmetic based on your written definitions.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakenone
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou confused the numerator and denominator in the Sheldon definition, defining it as product over waste rather than waste over product.
REASONING PATH
Your ACEpath teacher’s suggested approach- Green Chemistry Definition of E-factor
(an of 0 is ideal, meaning zero waste).
Always verify that waste is in the numerator so that a higher directly reflects a more wasteful chemical process.
- Sanity Check on Percentage Yield
For a pure isolated chemical reaction, .
If your calculated yield is substantially greater than , immediately pause and check whether actual mass was overestimated or a metric ratio was inverted.
CORRECTED PATH
ACEpath Teacher's DemonstrationApply the standard Sheldon definition: .
Rearrange to solve for the actual product mass: .
Substitute the corrected actual mass into the percentage yield formula: .
(a) ; (b)
02 The student confuses theoretical maximum yield with actual product yield in the percentage yield formula by placing theoretical yield in the numerator.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You inverted the fraction. Percentage yield measures what fraction of the stoichiometric maximum was actually obtained, so actual yield must be in the numerator and theoretical yield in the denominator.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly recalled and rearranged the relationship to isolate the actual mass of the product.
You accurately calculated the isolated product mass as .
You correctly identified the two quantities needed to evaluate reaction efficiency.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou swapped the numerator and denominator in the percentage yield formula, placing theoretical yield on top.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou confused the baseline reference quantity (theoretical maximum) with the observed outcome (actual yield). Remember that theoretical yield is the 'whole' (denominator), while actual yield is the 'part' obtained (numerator).
REASONING PATH
Your ACEpath teacher’s suggested approach- Ratio Structure of Yield
Always place the real amount produced in the numerator and the theoretical maximum in the denominator.
- Sanity Check for Yields
For pure isolated products under standard conditions, .
If your calculated percentage yield exceeds , immediately verify whether your ratio is upside down.
CORRECTED PATH
ACEpath Teacher's DemonstrationState the definition of percentage yield: .
Substitute the actual isolated mass () and theoretical yield (): .
Evaluate the quotient: , which rounds to .
(a) ; (b)
03 The student confuses the E-factor with atom economy or total mass balance by defining E-factor as waste divided by the theoretical maximum yield rather than actual product mass.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
The Sheldon Environmental Factor is defined strictly as the ratio of total waste mass to the actual mass of isolated product: . You added the theoretical yield to the waste mass and divided that sum by the , which resulted in an actual product mass greater than the theoretical maximum.
- Step 2Correct
You correctly selected and applied the percentage yield formula, but your result was affected by the incorrect product mass carried over from Part (a). Obtaining a yield over is also an immediate indicator that the earlier mass calculation was too high.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly stated the formula for percentage yield as the ratio of actual yield to theoretical yield multiplied by .
You carried out your arithmetic and rounding accurately across both calculation steps.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou divided an estimated raw material total by the rather than dividing the total waste directly.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou conflated the ratio with a total mass balance metric. Because , the mass of waste alone is the numerator; you do not need to reconstruct total input materials or involve theoretical yield in the equation.
REASONING PATH
Your ACEpath teacher’s suggested approach- Definition of Environmental Factor
Rearrange directly to solve for product mass: .
- Physical Yield Sanity Check
In an ideal stoichiometry model without unreacted impurities or solvent retention, .
If your calculated actual yield exceeds the theoretical yield (giving ), pause and re-check the definition used to find the isolated mass.
CORRECTED PATH
ACEpath Teacher's Demonstration(a) ; (b)
Lock it in
What is the mathematical definition and physical meaning of the Environmental Factor () in green chemistry?
. It quantifies kilograms of chemical waste generated per single kilogram of desired product.
Similar question
A chemical synthesis operates with an of and produces of total waste. Calculate the mass of isolated target product obtained from this synthesis.
Answer
. Key steps: .
A specialty solvent recovery run has a theoretical yield of . During the run, of total waste was generated and an of was recorded. Determine: (a) the actual mass of solvent recovered, and (b) the reaction percentage yield.
Answer
(a) ; (b) . Key steps: . .
An active pharmaceutical ingredient (API) is manufactured from of total raw materials. The process achieves an actual isolated yield of of pure API against a theoretical yield of . Assuming all input material not converted to isolated product constitutes waste: (a) calculate the , and (b) calculate the percentage yield.
Answer
(a) ; (b) . Key steps: . . .