Resources

An industrial microelectronics interconnect line made of gold has a rectangular cross section with width w=250 nmw = 250\text{ nm} and thickness t=80.0 nmt = 80.0\text{ nm}. The length of the trace is L=4.50 mmL = 4.50\text{ mm}. At operating temperature, the resistivity of bulk gold is given in non-standard units as ρ=0.0244 Ω⋅mm2⋅m−1\rho = 0.0244\ \Omega\cdot\text{mm}^2\cdot\text{m}^{-1}. (a) Convert the cross-sectional area of the gold trace into square millimeters (mm2\text{mm}^2). (b) Convert the resistivity into standard SI units of Ω⋅m\Omega\cdot\text{m}. (c) Calculate the total resistance RR of the interconnect line in ohms (Ω\Omega).

Answer and steps

Final answer

(a) A=2.00×10−8 mm2A = 2.00 \times 10^{-8}\text{ mm}^2; (b) ρ=2.44×10−8 Ω⋅m\rho = 2.44 \times 10^{-8}\ \Omega\cdot\text{m}; (c) R=5.49 ΩR = 5.49\ \Omega

Steps

Part (a): Cross-Sectional Area in mm2\text{mm}^2

  1. Calculate the area in square nanometers (nm2\text{nm}^2): The cross section of the trace is rectangular with width w=250 nmw = 250\text{ nm} and thickness t=80.0 nmt = 80.0\text{ nm}: A=w⋅t=(250 nm)⋅(80.0 nm)=20 000 nm2=2.00×104 nm2A = w \cdot t = (250\text{ nm}) \cdot (80.0\text{ nm}) = 20\,000\text{ nm}^2 = 2.00 \times 10^4\text{ nm}^2
  2. Convert square nanometers to square millimeters (mm2\text{mm}^2): Since 1 mm=10−3 m1\text{ mm} = 10^{-3}\text{ m} and 1 nm=10−9 m1\text{ nm} = 10^{-9}\text{ m}, the linear conversion factor is: 1 mm=106 nm  ⟹  1 nm=10−6 mm1\text{ mm} = 10^6\text{ nm} \implies 1\text{ nm} = 10^{-6}\text{ mm} Squaring both sides gives the area conversion factor: 1 nm2=(10−6 mm)2=10−12 mm21\text{ nm}^2 = (10^{-6}\text{ mm})^2 = 10^{-12}\text{ mm}^2
  3. Compute the final area: A=(2.00×104 nm2)⋅(10−12 mm2⋅nm−2)=2.00×10−8 mm2A = (2.00 \times 10^4\text{ nm}^2) \cdot (10^{-12}\text{ mm}^2\cdot\text{nm}^{-2}) = 2.00 \times 10^{-8}\text{ mm}^2

Part (b): Resistivity in SI Units (Ω⋅m\Omega\cdot\text{m})

  1. Identify the unit relation: The given resistivity is in mixed units: ρ=0.0244 Ω⋅mm2⋅m−1\rho = 0.0244\ \Omega\cdot\text{mm}^2\cdot\text{m}^{-1} To convert mm2\text{mm}^2 to m2\text{m}^2, recall that 1 mm=10−3 m1\text{ mm} = 10^{-3}\text{ m}, so: 1 mm2=(10−3 m)2=10−6 m21\text{ mm}^2 = (10^{-3}\text{ m})^2 = 10^{-6}\text{ m}^2
  2. Substitute and simplify: ρ=0.0244 Ω⋅(10−6 m2)m=0.0244×10−6 Ω⋅m=2.44×10−8 Ω⋅m\rho = 0.0244\ \frac{\Omega\cdot(10^{-6}\text{ m}^2)}{\text{m}} = 0.0244 \times 10^{-6}\ \Omega\cdot\text{m} = 2.44 \times 10^{-8}\ \Omega\cdot\text{m}

Part (c): Total Resistance of the Interconnect Line

  1. State the resistance formula: Electrical resistance depends on resistivity ρ\rho, length LL, and cross-sectional area AA: R=ρ⋅LAR = \rho \cdot \frac{L}{A}
  2. Express all parameters in consistent SI units:

    • ρ=2.44×10−8 Ω⋅m\rho = 2.44 \times 10^{-8}\ \Omega\cdot\text{m}
    • L=4.50 mm=4.50×10−3 mL = 4.50\text{ mm} = 4.50 \times 10^{-3}\text{ m}
    • A=2.00×10−8 mm2⋅(10−6 m2⋅mm−2)=2.00×10−14 m2A = 2.00 \times 10^{-8}\text{ mm}^2 \cdot (10^{-6}\text{ m}^2\cdot\text{mm}^{-2}) = 2.00 \times 10^{-14}\text{ m}^2
  3. Calculate the resistance: R=(2.44×10−8 Ω⋅m)⋅4.50×10−3 m2.00×10−14 m2R = (2.44 \times 10^{-8}\ \Omega\cdot\text{m}) \cdot \frac{4.50 \times 10^{-3}\text{ m}}{2.00 \times 10^{-14}\text{ m}^2} R=1.098×10−102.00×10−14 Ω=5.49 ΩR = \frac{1.098 \times 10^{-10}}{2.00 \times 10^{-14}}\ \Omega = 5.49\ \Omega

(Note: A common pitfall is forgetting to square the conversion factor when converting units of area, e.g., converting nm2\text{nm}^2 using 10−610^{-6} instead of (10−6)2=10−12(10^{-6})^2 = 10^{-12}.)

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets that area conversion requires squaring the linear conversion factor, using 1 mm = 10⁶ nm instead of 1 mm² = 10¹² nm².

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    A=250 nm×80.0 nm=20000 nm2  ⟹  A=20000 nm2×(1 mm106 nm)=0.0200 mm2A = 250\text{ nm} \times 80.0\text{ nm} = 20000\text{ nm}^2 \implies A = 20000\text{ nm}^2 \times \left(\frac{1\text{ mm}}{10^6\text{ nm}}\right) = 0.0200\text{ mm}^2

    Correct

    A=20000 nm2×(1 mm106 nm)2=2.00×10−8 mm2A = 20000\text{ nm}^2 \times \left(\frac{1\text{ mm}}{10^6\text{ nm}}\right)^2 = 2.00 \times 10^{-8}\text{ mm}^2

    You multiplied width by thickness correctly, but you used the linear conversion factor 1 mm106 nm\frac{1\text{ mm}}{10^6\text{ nm}} without squaring it. Because area has units of length squared, the conversion factor must be squared: (1 mm106 nm)2=1 mm21012 nm2\left(\frac{1\text{ mm}}{10^6\text{ nm}}\right)^2 = \frac{1\text{ mm}^2}{10^{12}\text{ nm}^2}.

  2. Step 2

    ρ=0.0244 Ω⋅mm2m×(10−6 m21 mm2)=2.44×10−8 Ω⋅m\rho = 0.0244\ \frac{\Omega\cdot\text{mm}^2}{\text{m}} \times \left(\frac{10^{-6}\text{ m}^2}{1\text{ mm}^2}\right) = 2.44 \times 10^{-8}\ \Omega\cdot\text{m}

  3. Step 3

    L=4.50 mm=4.50×10−3 m  ⟹  R=0.0244 Ω⋅mm2m×4.50×10−3 m0.0200 mm2=0.00549 ΩL = 4.50\text{ mm} = 4.50 \times 10^{-3}\text{ m} \implies R = \frac{0.0244\ \frac{\Omega\cdot\text{mm}^2}{\text{m}} \times 4.50 \times 10^{-3}\text{ m}}{0.0200\text{ mm}^2} = 0.00549\ \Omega

    Correct

    R=ρLA=0.0244 Ω⋅mm2m×4.50×10−3 m2.00×10−8 mm2=5.49 ΩR = \frac{\rho L}{A} = \frac{0.0244\ \frac{\Omega\cdot\text{mm}^2}{\text{m}} \times 4.50 \times 10^{-3}\text{ m}}{2.00 \times 10^{-8}\text{ mm}^2} = 5.49\ \Omega

    You correctly matched the units of ρ\rho, LL, and AA in the resistance formula R=ρLAR = \frac{\rho L}{A}, but your result was altered because you substituted the incorrect area value from part (a).

WHAT YOU DID WELL
Compliments from Your Teacher

You calculated the raw area in square nanometers accurately from width and thickness.

You correctly converted the mixed resistivity value into standard SI units in part (b).

You set up the resistance formula R=ρLAR = \frac{\rho L}{A} with dimensionally consistent units.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Unsquared unit conversion factor for area

You wrote mm2\text{mm}^2 in the numerator of your conversion factor without raising the conversion factor 106 nm10^6\text{ nm} to the second power.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Treating derived two-dimensional area conversions as one-dimensional linear conversions by forgetting that (a unit1)2=a2 unit12(a\text{ unit}_1)^2 = a^2\text{ unit}_1^2.

REASONING PATH
Your ACEpath teacher’s suggested approach
Dimensional power rule for unit factors
  • When converting an area (length2)(\text{length}^2) or volume (length3)(\text{length}^3), the entire linear conversion factor ratio must be raised to that same power: (1 unitA/x unitB)n(1\text{ unit}_A / x\text{ unit}_B)^n.

  • Always write out parentheses around the entire conversion fraction and apply the exponent to both the unit and the numerical prefix.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Square the linear ratio between millimeters and nanometers: (1 mm106 nm)2=1 mm21012 nm2\left(\frac{1\text{ mm}}{10^6\text{ nm}}\right)^2 = \frac{1\text{ mm}^2}{10^{12}\text{ nm}^2}.

  2. Multiply the area by the squared factor: A=20000 nm2×10−12 mm2⋅nm−2=2.00×10−8 mm2A = 20000\text{ nm}^2 \times 10^{-12}\text{ mm}^2\cdot\text{nm}^{-2} = 2.00 \times 10^{-8}\text{ mm}^2.

  3. Substitute the corrected area into your resistance formula: R=0.0244 Ω⋅mm2⋅m−1×4.50×10−3 m2.00×10−8 mm2=5.49 ΩR = \frac{0.0244\ \Omega\cdot\text{mm}^2\cdot\text{m}^{-1} \times 4.50 \times 10^{-3}\text{ m}}{2.00 \times 10^{-8}\text{ mm}^2} = 5.49\ \Omega.

Final answer

(a) A=2.00×10−8 mm2A = 2.00 \times 10^{-8}\text{ mm}^2; (b) ρ=2.44×10−8 Ω⋅m\rho = 2.44 \times 10^{-8}\ \Omega\cdot\text{m}; (c) R=5.49 ΩR = 5.49\ \Omega

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice converting units with powers (2^2 and 3^3) by explicitly squaring or cubing both the number and the unit symbol.

  • Double-check reasonableness: 250 nm250\text{ nm} is 2.5×10−4 mm2.5 \times 10^{-4}\text{ mm} and 80 nm80\text{ nm} is 8.0×10−5 mm8.0 \times 10^{-5}\text{ mm}, so their product must be on the order of 10−8 mm210^{-8}\text{ mm}^2, not 10−2 mm210^{-2}\text{ mm}^2.

OverviewACEpath Teacher's Diagnosis

02 The student multiplies by 10⁶ instead of dividing by 10⁶ when converting mm² to m² in the numerator of the resistivity unit.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    w=250×10−6 mm  ⟹  t=80.0×10−6 mm  ⟹  A=(250×10−6 mm)×(80.0×10−6 mm)=2.00×10−8 mm2w = 250 \times 10^{-6}\text{ mm} \implies t = 80.0 \times 10^{-6}\text{ mm} \implies A = (250 \times 10^{-6}\text{ mm}) \times (80.0 \times 10^{-6}\text{ mm}) = 2.00 \times 10^{-8}\text{ mm}^2

  2. Step 2

    ρ=0.0244×106 Ω⋅m=24400 Ω⋅m\rho = 0.0244 \times 10^6\ \Omega\cdot\text{m} = 24400\ \Omega\cdot\text{m}

    Correct

    ρ=0.0244⋅Ω⋅(10−6 m2)m=2.44×10−8 Ω⋅m\rho = 0.0244 \cdot \frac{\Omega\cdot(10^{-6}\text{ m}^2)}{\text{m}} = 2.44 \times 10^{-8}\ \Omega\cdot\text{m}

    You multiplied by 10610^6 instead of 10−610^{-6}. Because 1 mm=10−3 m1\text{ mm} = 10^{-3}\text{ m}, one square millimeter is (10−3 m)2=10−6 m2(10^{-3}\text{ m})^2 = 10^{-6}\text{ m}^2, so converting mm2\text{mm}^2 in the numerator requires multiplying by 10−610^{-6}.

  3. Step 3

    L=4.50 mm=4.50×10−3 m  ⟹  R=0.0244 Ω⋅mm2/m×4.50×10−3 m2.00×10−8 mm2=5490 ΩL = 4.50\text{ mm} = 4.50 \times 10^{-3}\text{ m} \implies R = \frac{0.0244\ \Omega\cdot\text{mm}^2/\text{m} \times 4.50 \times 10^{-3}\text{ m}}{2.00 \times 10^{-8}\text{ mm}^2} = 5490\ \Omega

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted nanometers to millimeters and found the cross-sectional area.

You applied the resistance formula R=ρLAR = \frac{\rho L}{A} with correct unit cancellation.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted Area Unit Conversion

You multiplied by 10610^6 instead of 10−610^{-6} when replacing mm2\text{mm}^2 with m2\text{m}^2.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

When converting a derived unit containing an area in the numerator, substituting a smaller prefix unit (mm2\text{mm}^2) for a base unit (m2\text{m}^2) requires the scale factor (10−3)2=10−6(10^{-3})^2 = 10^{-6}, not the count of small units per large unit (10610^6).

REASONING PATH
Your ACEpath teacher’s suggested approach
Substitute Units Directly
  • 1 mm=10−3 m  ⟹  1 mm2=(10−3 m)2=10−6 m21\text{ mm} = 10^{-3}\text{ m} \implies 1\text{ mm}^2 = (10^{-3}\text{ m})^2 = 10^{-6}\text{ m}^2

  • Replace the symbol mm2\text{mm}^2 with its equivalent (10−6 m2)(10^{-6}\text{ m}^2) directly in the unit expression.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Replace mm2\text{mm}^2 with (10−3 m)2=10−6 m2(10^{-3}\text{ m})^2 = 10^{-6}\text{ m}^2: ρ=0.0244⋅Ω⋅(10−6 m2)m\rho = 0.0244 \cdot \frac{\Omega\cdot(10^{-6}\text{ m}^2)}{\text{m}}

  2. Simplify the units and combine powers: ρ=0.0244×10−6 Ω⋅m=2.44×10−8 Ω⋅m\rho = 0.0244 \times 10^{-6}\ \Omega\cdot\text{m} = 2.44 \times 10^{-8}\ \Omega\cdot\text{m}

Final answer

(a) A=2.00×10−8 mm2A = 2.00 \times 10^{-8}\text{ mm}^2; (b) ρ=2.44×10−8 Ω⋅m\rho = 2.44 \times 10^{-8}\ \Omega\cdot\text{m}; (c) R=5490 Ω (5.49×103 Ω)R = 5490\ \Omega\ (5.49 \times 10^3\ \Omega)

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice replacing compound units algebraically rather than guessing whether to multiply or divide.

  • Confirm that converting a smaller area unit to a larger area unit always yields a smaller numerical coefficient.

OverviewACEpath Teacher's Diagnosis

03 The student fails to convert the length L from millimeters to meters when evaluating resistance with ρ in Ω·mm²·m⁻¹ and A in mm².

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    w=2.50×10−4 mm  ⟹  t=8.00×10−5 mm  ⟹  A=(2.50×10−4 mm)×(8.00×10−5 mm)=2.00×10−8 mm2w = 2.50 \times 10^{-4}\text{ mm} \implies t = 8.00 \times 10^{-5}\text{ mm} \implies A = (2.50 \times 10^{-4}\text{ mm}) \times (8.00 \times 10^{-5}\text{ mm}) = 2.00 \times 10^{-8}\text{ mm}^2

  2. Step 2

    ρ=0.0244 Ω⋅mm2/m×10−6 m2/mm2=2.44×10−8 Ω⋅m\rho = 0.0244\ \Omega\cdot\text{mm}^2/\text{m} \times 10^{-6}\text{ m}^2/\text{mm}^2 = 2.44 \times 10^{-8}\ \Omega\cdot\text{m}

  3. Step 3

    R=ρ×LA  ⟹  R=(0.0244×4.50)2.00×10−8=5.49×106 ΩR = \rho \times \frac{L}{A} \implies R = \frac{(0.0244 \times 4.50)}{2.00 \times 10^{-8}} = 5.49 \times 10^6\ \Omega

    Correct

    R=ρLA=(0.0244 Ω⋅mm2⋅m−1)⋅(4.50×10−3 m)2.00×10−8 mm2=5.49 ΩR = \frac{\rho L}{A} = \frac{(0.0244\ \Omega\cdot\text{mm}^2\cdot\text{m}^{-1}) \cdot (4.50 \times 10^{-3}\text{ m})}{2.00 \times 10^{-8}\text{ mm}^2} = 5.49\ \Omega

    Because the given resistivity ρ\rho contains m−1\text{m}^{-1}, the length LL must be in meters (4.50×10−3 m4.50 \times 10^{-3}\text{ m}) rather than millimeters (4.50 mm4.50\text{ mm}) to allow the length units to cancel.

WHAT YOU DID WELL
Compliments from Your Teacher

You converted nanometers to millimeters accurately when finding the cross-sectional area.

You applied the proper conversion factor from mm2\text{mm}^2 to m2\text{m}^2 to find the SI resistivity.

You selected the correct physical relationship R=ρLAR = \frac{\rho L}{A} for resistance.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inconsistent Unit Substitution

You substituted the length as 4.504.50 without converting millimeters to meters to match the m−1\text{m}^{-1} in ρ\rho.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Overlooking internal unit breakdown in composite units: Ω⋅mm2⋅m−1\Omega\cdot\text{mm}^2\cdot\text{m}^{-1} requires area in mm2\text{mm}^2 and length in m\text{m}. Alternatively, converting every parameter to pure SI base units before substitution prevents dimensional mismatch.

REASONING PATH
Your ACEpath teacher’s suggested approach
Inspect Composite Units
  • Every individual dimension inside a compound unit (such as mm2\text{mm}^2 and m−1\text{m}^{-1}) must match the units of the corresponding physical quantities.

  • Write out explicit unit labels alongside each numerical value during substitution to verify that all length units cancel out to leave only Ω\Omega.

Use Pure SI Quantities
  • Working strictly in SI base units (m\text{m}, m2\text{m}^2, Ω⋅m\Omega\cdot\text{m}) eliminates unit conflicts.

  • Use the SI resistivity ρ=2.44×10−8 Ω⋅m\rho = 2.44 \times 10^{-8}\ \Omega\cdot\text{m} found in part (b) along with LL in meters and AA in square meters.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Identify the length in meters: L=4.50 mm=4.50×10−3 mL = 4.50\text{ mm} = 4.50 \times 10^{-3}\text{ m}.

  2. Substitute into R=ρLAR = \frac{\rho L}{A} with matching units: R=(0.0244 Ω⋅mm2⋅m−1)(4.50×10−3 m)2.00×10−8 mm2R = \frac{(0.0244\ \Omega\cdot\text{mm}^2\cdot\text{m}^{-1})(4.50 \times 10^{-3}\text{ m})}{2.00 \times 10^{-8}\text{ mm}^2}.

  3. Cancel the units mm2\text{mm}^2 and m\text{m}, then evaluate: R=1.098×10−42.00×10−8 Ω=5.49 ΩR = \frac{1.098 \times 10^{-4}}{2.00 \times 10^{-8}}\ \Omega = 5.49\ \Omega.

Final answer

R=5.49 ΩR = 5.49\ \Omega

NEXT STEPS
Final Takeaways from Your Teacher
  • Include unit symbols inside every calculation step rather than writing naked numbers.

  • Check that your final resistance value is physically reasonable for a microscopic metal interconnect before concluding.

Lock it in

Similar question

01

A square copper contact pad on an integrated circuit has side lengths of s=400.0 nms = 400.0\text{ nm}. Calculate its area in square micrometers (μm2\mu\text{m}^2).

Answer

A=0.1600 μm2A = 0.1600\ \mu\text{m}^2. Key steps: A=(400.0 nm)2=1.600×105 nm2A = (400.0\text{ nm})^2 = 1.600 \times 10^5\text{ nm}^2. Since 1 μm=103 nm1\ \mu\text{m} = 10^3\text{ nm}, the area conversion factor is (10−3 μm/nm)2=10−6 μm2/nm2\left(10^{-3}\ \mu\text{m}/\text{nm}\right)^2 = 10^{-6}\ \mu\text{m}^2/\text{nm}^2. Therefore, A=(1.600×105)×10−6=0.1600 μm2A = (1.600 \times 10^5) \times 10^{-6} = 0.1600\ \mu\text{m}^2.

02

An aluminum interconnect trace has a rectangular cross section with width w=120 nmw = 120\text{ nm} and thickness t=50.0 nmt = 50.0\text{ nm}, and a length of L=2.00 mmL = 2.00\text{ mm}. If the resistivity of aluminum is ρ=2.82×10−8 Ω⋅m\rho = 2.82 \times 10^{-8}\ \Omega\cdot\text{m}, calculate the resistance RR of the trace in ohms (Ω\Omega).

Answer

R=9.40 ΩR = 9.40\ \Omega. Key steps: Area in SI units is A=(120×10−9 m)×(50.0×10−9 m)=6.00×10−15 m2A = (120 \times 10^{-9}\text{ m}) \times (50.0 \times 10^{-9}\text{ m}) = 6.00 \times 10^{-15}\text{ m}^2. Length is L=2.00×10−3 mL = 2.00 \times 10^{-3}\text{ m}. Using R=ρLAR = \frac{\rho L}{A}: R=(2.82×10−8 Ω⋅m)(2.00×10−3 m)6.00×10−15 m2=9.40 ΩR = \frac{(2.82 \times 10^{-8}\ \Omega\cdot\text{m})(2.00 \times 10^{-3}\text{ m})}{6.00 \times 10^{-15}\text{ m}^2} = 9.40\ \Omega.

03

A silver nanowire with a circular cross section has radius r=25.0 nmr = 25.0\text{ nm} and length L=1.50 cmL = 1.50\text{ cm}. Silver has resistivity ρ=1.59×10−8 Ω⋅m\rho = 1.59 \times 10^{-8}\ \Omega\cdot\text{m}. Find the total resistance RR in ohms (Ω\Omega).

Answer

R=121 ΩR = 121\ \Omega. Key steps: Radius in meters is r=2.50×10−8 mr = 2.50 \times 10^{-8}\text{ m}. Cross-sectional area A=πr2=π(2.50×10−8 m)2≈1.9635×10−15 m2A = \pi r^2 = \pi (2.50 \times 10^{-8}\text{ m})^2 \approx 1.9635 \times 10^{-15}\text{ m}^2. Length in meters is L=1.50×10−2 mL = 1.50 \times 10^{-2}\text{ m}. Resistance R=ρLA=(1.59×10−8)(1.50×10−2)1.9635×10−15≈121.46 Ω≈121 ΩR = \frac{\rho L}{A} = \frac{(1.59 \times 10^{-8})(1.50 \times 10^{-2})}{1.9635 \times 10^{-15}} \approx 121.46\ \Omega \approx 121\ \Omega (to 3 significant figures).

Loading workspace…