Resources
A student mixes of solution with of solution at . The solubility product constant for barium sulfate, , is at this temperature. Calculate the initial ion product quotient, , immediately upon mixing and determine whether a precipitate of will form.
Answer and steps
Final answer
; since (), a precipitate of will form.
Steps
Calculate the Concentrations of the Reacting Ions After Mixing
When two solutions are combined, dilution occurs. First, calculate the total volume of the combined mixture:
Both barium nitrate, , and potassium sulfate, , are soluble strong electrolytes that dissociate completely in water:
Using the dilution formula (or by finding moles and dividing by total volume), determine the initial molarity of each ion in the mixed solution:
Common Pitfall: A frequent mistake is using the original concentrations before mixing to calculate . Always account for the dilution caused by combining the volumes.
Calculate the Reaction Quotient ()
The dissolution equilibrium for slightly soluble barium sulfate is:
The ion product quotient, , has the same mathematical form as the solubility product expression, , but uses initial non-equilibrium concentrations:
Substitute the diluted concentrations into the expression:
Compare to to Determine Precipitation
To determine if a precipitate forms, compare to :
- If , the solution is unsaturated; no precipitate forms.
- If , the solution is saturated at dynamic equilibrium; no precipitate forms.
- If , the solution is supersaturated; ions will combine to form a solid until equilibrium is reached.
Comparing the values:
Since (), the system will shift to the left to relieve the excess ion concentrations, and a precipitate of will form.
Typical errors
01 The student forgets to account for dilution upon mixing the two solutions, calculating Q using the undiluted stock concentrations.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You used the stock molarities directly instead of calculating the new ion concentrations after the two volumes are combined ().
- Step 2Correct
You correctly set up the reaction quotient expression, but your computed value of inherits the undiluted concentrations from Step 1.
- Step 3Correct
Your comparison logic is correct because indicates precipitation, but the comparison uses your earlier incorrect value.
WHAT YOU DID WELL
Compliments from Your TeacherYou identified the correct ions responsible for forming the insoluble precipitate.
You wrote the correct equilibrium expression for the reaction quotient .
You correctly stated the decision rule that a precipitate forms when .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou forgot to account for the increase in total solution volume upon mixing.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated the stock solution concentrations as the initial concentrations in the reaction mixture, overlooking that combining two liquid volumes dilutes both solutes before reaction occurs.
REASONING PATH
Your ACEpath teacher’s suggested approach- Total Volume Check
When two solutions are mixed, .
Add the volumes of both solutions before calculating any post-mixing ion concentrations.
- Dilution Calculation Check
for each separate ion.
Recalculate the molarity of each reacting species in the combined volume before substituting into .
CORRECTED PATH
ACEpath Teacher's DemonstrationCompare to : , so .
; since , a precipitate of will form.
02 The student calculates the moles of each ion correctly but forgets to divide by the total volume to find molarity, substituting mole quantities directly into the Q expression.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
,
You substituted moles instead of molar concentrations into the ion product expression. Remember to divide the moles of each ion by the total volume () before multiplying.
- Step 3Correct
Your comparison logic and precipitation conclusion are chemically sound, but they relied on your diluted numerical value of from the previous step.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the total volume of the combined mixture.
You accurately converted volumes to liters and determined the correct mole amounts of and .
You correctly stated the precipitation criterion that a solid forms when .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou found the total volume at the start of your work, but you bypassed dividing the moles by when calculating .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing extensive amounts (moles, ) with intensive concentrations (molarity, ) when evaluating mass-action expressions like and .
REASONING PATH
Your ACEpath teacher’s suggested approach- Equilibrium Expressions Require Concentration
Brackets in or expressions always represent molar concentrations (), not mole quantities.
Whenever two solutions are mixed, calculate or use before setting up .
CORRECTED PATH
ACEpath Teacher's DemonstrationFind the new molarity of each ion after dilution: and .
Evaluate the reaction quotient using concentrations: .
Compare to : since , the mixture is supersaturated.
; since , a precipitate of will form.
03 The student misinterprets the precipitation criterion, believing that a precipitate only forms when Q < K_sp rather than when Q > K_sp.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
You wrote that precipitation requires . In reality, represents the maximum ion product at saturation; when , the solution contains excess ions, shifting the dissolution equilibrium to the left to form solid precipitate.
- Step 4Correct
Because you applied the reversed precipitation criterion, your final conclusion was inverted.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the diluted concentrations of barium and sulfate ions after mixing.
You correctly set up and evaluated the ion product quotient as .
You accurately compared the numerical values of and .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeNo, this is a conceptual misconception regarding the meaning of the reaction quotient relative to solubility product equilibrium.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated as an upper threshold that must stay below to precipitate, rather than recognizing that dissolution is written as . When , there are more dissolved ions than the saturated equilibrium can hold, driving the reverse reaction to form solid precipitate.
REASONING PATH
Your ACEpath teacher’s suggested approach- Direction of Equilibrium Shift
For , reflects the dissolved product side.
Remember that if , product concentration is in excess, so Le Chatelier's principle shifts the system left (toward solid precipitate).
- Interpreting Saturation States
: unsaturated (no precipitate); : saturated at equilibrium; : supersaturated (precipitate forms).
Always verify whether the ion product exceeds the equilibrium limit before concluding whether precipitation occurs.
CORRECTED PATH
ACEpath Teacher's DemonstrationState the correct precipitation condition: a precipitate forms when the solution is supersaturated, which occurs when .
Compare the values: and . Since , the condition is met.
Conclude that equilibrium shifts toward the reactant solid, so a precipitate of will form.
; since (), a precipitate of will form.
Lock it in
When mixing two solutions, why can't you directly use the stock molarities to calculate ?
Combining solutions increases the total volume, which dilutes both ions: .
Similar question
A student mixes of with of at . For , . Calculate and state whether will precipitate.
Answer
; no precipitate forms. Key steps: ; ; ; ; since , no precipitate forms.
A solution is prepared by mixing of with of . If for is , determine and whether precipitation occurs.
Answer
; no precipitate forms. Key steps: ; ; ; ; since , no precipitate forms.
What minimum volume of must be added to of to just begin precipitation of ()?
Answer
(or ). Key steps: At onset of precipitation, . Let added volume be . and . Setting and approximating yields , confirming even a single micro-drop initiates precipitation.