Resources
A student heats a sample of blue copper(II) sulfate pentahydrate, , to drive off the waters of hydration. However, the crucible is underheated, leaving a partially dehydrated solid with the composition . If gravimetric analysis shows that water still accounts for exactly of the partially dehydrated sample's total mass, determine the value of the hydration coefficient . Use molar masses: and . Round to two decimal places.
Answer and steps
Final answer
Steps
To find the hydration coefficient in the formula , we need to determine the molar ratio of water molecules to anhydrous copper(II) sulfate units.
Method 1: Assume a Sample
- Find the masses of each component: Since water makes up of the total mass, the remaining percentage corresponds to anhydrous : In a sample of :
- Convert each mass to moles: Using the given molar masses ( and ):
-
Determine the mole ratio : The hydration coefficient represents the moles of water per mole of anhydrous salt:
Rounding to two decimal places gives .
Alternative Method: Direct Algebraic Equation
Alternatively, express the mass percent of water in terms of for of hydrate:
Cross-multiply and solve for :
Common Pitfall: Do not set the water percentage against the anhydrous mass alone; percent composition is always defined relative to the total mass of the hydrated compound ().
Typical errors
01 The student calculates the mass percentage of water relative to the anhydrous salt rather than the total sample mass.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
Percent composition by mass is defined as the mass of the component divided by the total mass of the compound. The denominator must include both the anhydrous salt and the waters of hydration ().
- Step 2Correct
Your algebraic rearrangement was executed correctly based on your equation, but it carries forward the missing water term from the denominator.
- Step 3Correct
Your final calculation followed from your initial formula, but the result is incorrect due to the omitted denominator term.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly expressed the total mass of water in one mole of the hydrate as .
You correctly converted the percentage to its decimal equivalent .
You carried out the linear algebraic steps accurately according to your setup.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the mass of the anhydrous salt with the total mass of the hydrated compound when calculating mass percent.
REASONING PATH
Your ACEpath teacher’s suggested approach- Definition of Percent Composition
Always verify that the denominator represents the entire sample (salt plus water), not just the anhydrous part.
CORRECTED PATH
ACEpath Teacher's Demonstration02 The student inverts the mole ratio by dividing the moles of anhydrous CuSO4 by the moles of H2O.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
In the chemical formula , the subscript represents the number of moles of water per one mole of anhydrous . You calculated instead of .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly used the given mass percentage to find the masses of both water and anhydrous salt in a standard sample.
You correctly converted the masses of water and copper(II) sulfate into their respective molar quantities using accurate molar masses.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou set up the ratio as moles of salt over moles of water instead of moles of water over moles of salt.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing which component belongs in the numerator when solving for the hydration coefficient . In , is defined as the moles of associated with exactly of the anhydrous salt, requiring .
REASONING PATH
Your ACEpath teacher’s suggested approach- Define the Hydration Ratio
A hydrate formula means there are moles of water for every of anhydrous salt.
Always write down the explicit unit formula before substituting numbers.
CORRECTED PATH
ACEpath Teacher's DemonstrationSet up the ratio of water to anhydrous salt: .
Substitute the calculated molar values: .
Evaluate and round to two decimal places: .
03 The student takes the ratio of the component masses directly without converting to moles.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
,
You calculated by taking the ratio of component masses. In a chemical formula, coefficients represent molar ratios (the count of particles/moles), so you must divide each mass by its molar mass before taking the ratio.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly used the percentage to find the mass of water and the remaining mass of anhydrous salt in a sample.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeDividing masses directly to calculate a formula subscript or coefficient.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisTreating chemical formula coefficients as mass proportions rather than mole proportions.
REASONING PATH
Your ACEpath teacher’s suggested approach- Subscripts and Coefficients Count Moles
Every subscript or coefficient in a chemical formula represents a molar ratio: .
Always convert component masses to moles before forming any formula ratio.
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate moles of water: .
Calculate moles of anhydrous salt: .
Divide moles of water by moles of anhydrous salt: .
Lock it in
What is the correct denominator when expressing the mass percent of water in a hydrate formula ?
The total molar mass of the hydrate, , never the anhydrous salt alone.
Similar question
A sample of barium chloride dihydrate, , is analyzed. Calculate the theoretical mass percent of water in this compound. (Molar masses: , . Round to two decimal places.)
Answer
Total molar mass . Mass percent of water .
A partially dried sample of magnesium sulfate hydrate, , contains water by mass. Determine the value of . (Molar masses: , . Round to two decimal places.)
Answer
In a sample, and . Moles: , . Ratio .
A sample of hydrated cobalt(II) chloride, , is heated until all water is driven off, leaving of anhydrous . Calculate the hydration integer . (Molar masses: , . Round to the nearest whole integer.)
Answer
Mass of water lost . Moles of . Moles of . Mole ratio .