Resources
Solid calcium phosphate reacts with liquid sulfuric acid and water to produce calcium sulfate dihydrate (gypsum) and phosphoric acid via the process: Balance the equation using the smallest positive integers . If of (molar mass ) is reacted with excess sulfuric acid and water at an yield, calculate the mass of gypsum (, molar mass ) isolated.
Answer and steps
Final answer
Balanced equation: ; mass of gypsum isolated is .
Steps
Balance the Chemical Equation
Start with the unbalanced equation:
- Balance calcium (): Set . The left side has calcium atoms from , which requires:
- Balance phosphorus (): The left side has phosphorus atoms from , which requires:
- Balance sulfate (): The right side contains sulfate units in , which requires:
-
Balance hydrogen ():
- Total hydrogen on the right side:
- Hydrogen from sulfuric acid on the left side:
- The remaining hydrogen must come from :
-
Verify oxygen ():
- Left side:
- Right side:
The balanced equation is:
Calculate the Theoretical Yield of Gypsum
- Find the moles of reacted:
- Use the stoichiometric ratio: From the balanced equation, produces :
- Convert theoretical moles to mass:
Calculate the Actual Mass Isolated
Given a percentage yield of :
Typical errors
01 A student might omit the 1:3 stoichiometric mole ratio between Ca3(PO4)2 and CaSO4·2H2O, assuming a 1:1 molar ratio and obtaining one-third of the correct yield.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
You assumed a 1:1 mole ratio between and , but the balanced reaction shows that of produces of gypsum ().
- Step 4Correct
You multiplied by the molar mass correctly, but the numerical result is off because the mole quantity carried over from Step 3 was one-third of the correct value.
- Step 5Correct
You applied the yield factor correctly, but your final answer inherited the missing factor of from Step 3.
WHAT YOU DID WELL
Compliments from Your TeacherYou systematically balanced all elements in the chemical equation, including hydrate waters.
You correctly calculated the amount of starting material in moles.
You properly applied the percent yield formula to obtain the actual yield from theoretical yield.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakenone
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated the reaction as an equimolar 1:1 transformation rather than using the stoichiometric coefficients () derived in your balanced equation.
REASONING PATH
Your ACEpath teacher’s suggested approach- Mole-to-Mole Stoichiometric Factor
For any general reaction , the moles of product formed are related by .
Always write out the stoichiometric conversion factor explicitly before calculating theoretical mass.
CORRECTED PATH
ACEpath Teacher's DemonstrationBalanced equation: ; mass of gypsum isolated is .
02 A student might divide by the percent yield instead of multiplying by it when calculating actual mass from theoretical mass, obtaining an erroneously inflated yield.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
You divided by the fractional percent yield () instead of multiplying by it. Because percent yield is defined as , the isolated mass must be less than the theoretical maximum: .
WHAT YOU DID WELL
Compliments from Your TeacherYou systematically balanced all elements in the chemical equation to obtain the correct integer coefficients.
You correctly used molar masses and stoichiometric ratios to determine the theoretical yield of gypsum.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou divided the theoretical yield by rather than multiplying by .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated percent yield as an expansion factor or mixed up the numerator and denominator in the definition . Because real-world yields are less than , the actual mass obtained in the lab must always be smaller than the calculated theoretical mass.
REASONING PATH
Your ACEpath teacher’s suggested approach- Sanity Check Real-World Yield
For any non-exceptional reaction, .
Whenever the percent yield is under , check that your calculated actual mass is strictly smaller than the theoretical mass.
- Percent Yield Rearrangement
.
Multiply the theoretical yield by the decimal percentage to find the actual amount isolated.
CORRECTED PATH
ACEpath Teacher's Demonstration03 A student might neglect the water of crystallization in the dihydrate product when counting hydrogen atoms during balancing, resulting in an incorrect water coefficient c = 3.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You omitted the hydrogen atoms from the dihydrate crystal water in ( hydrogen atoms). You also evaluated as , arriving at instead of .
- Step 3Correct
Because of the hydrogen balancing error in the previous step, your coefficient for is rather than .
- Step 4
- Step 5
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly balanced the calcium, phosphorus, and sulfate components.
You used the correct stoichiometric ratio between and gypsum.
You accurately carried out the molar conversions and percentage yield calculation.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou evaluated as when solving your hydrogen conservation equation.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated hydrated salts as if the dot formula were separate from the element inventory, failing to include its hydrogen and oxygen atoms in the product-side count.
REASONING PATH
Your ACEpath teacher’s suggested approach- Hydrate atom inventory
Every unit of a hydrate contains hydrogen atoms and additional oxygen atoms that must be counted when balancing.
Always write down the full molecular atom breakdown for hydrate formulas before balancing hydrogen and oxygen.
CORRECTED PATH
ACEpath Teacher's DemonstrationWrite the complete hydrogen atom balance across both sides: .
Substitute the known coefficients , , and : .
Solve for : .
State the complete set of integer coefficients: , , , , .
Balanced equation: ; isolated gypsum mass: .
Lock it in
How do you determine the theoretical moles of a product from the moles of limiting reactant in ?
. Always multiply by the mole ratio of target to known from the balanced equation.
Similar question
In the reaction , how many moles of are produced from of with excess sulfuric acid?
Answer
. Step 1: Identify mole ratio . Step 2: Multiply .
Dinitrogen pentoxide decomposes according to . If of () decomposes with an yield, what mass of () is collected?
Answer
. Step 1: . Step 2: . Step 3: Theoretical mass . Step 4: Actual mass .
Magnetite is reduced in a blast furnace: . A sample of of () produces of iron (). Calculate the percentage yield of the reaction.
Answer
. Step 1: . Step 2: Theoretical . Step 3: Theoretical mass . Step 4: Percent yield .