Resources

A 250.0 mL250.0\text{ mL} aqueous industrial effluent sample contains copper(II) ions at a concentration of 128.0 ppm128.0\text{ ppm} (where 1 ppm=1.00 mg/L1\text{ ppm} = 1.00\text{ mg/L}, density of solution ρ=1.00 g/mL\rho = 1.00\text{ g/mL}). A hydrometallurgical technician adds excess ethylenediaminetetraacetate (extEDTA4− ext{EDTA}^{4-}), a hexadentate Lewis base, to form the stable chelate [Cu(EDTA)]2−[\text{Cu}(\text{EDTA})]^{2-} via a 1:11:1 stoichiometric coordination. (a) Convert the concentration of Cu2+\text{Cu}^{2+} in the effluent into millimoles per liter (mmol/L\text{mmol/L}) using the molar mass of copper (63.55 g/mol63.55\text{ g/mol}). (b) Calculate the minimum mass in milligrams of disodium EDTA dihydrate (Na2H2EDTA⋅2H2O\text{Na}_2\text{H}_2\text{EDTA}\cdot 2\text{H}_2\text{O}, molar mass =372.24 g/mol= 372.24\text{ g/mol}) required to stoichiometrically bind all the Cu2+\text{Cu}^{2+} Lewis acid ions in the 250.0 mL250.0\text{ mL} aliquot.

Answer and steps

Final answer

(a) Concentration of Cu2+=128.0 mg/L63.55 g/mol=2.014 mmol/L\text{Cu}^{2+} = \frac{128.0\text{ mg/L}}{63.55\text{ g/mol}} = 2.014\text{ mmol/L}; (b) Mass of Na2H2EDTA⋅2H2O=(2.014×10−3 mol/L)×0.2500 L×372.24 g/mol×103 mg/g=187.4 mg\text{Na}_2\text{H}_2\text{EDTA}\cdot 2\text{H}_2\text{O} = (2.014\times 10^{-3}\text{ mol/L}) \times 0.2500\text{ L} \times 372.24\text{ g/mol} \times 10^3\text{ mg/g} = 187.4\text{ mg}.

Steps

Part (a): Determining the Molar Concentration of CuX2+\ce{Cu^{2+}}

  1. Interpret the Parts-Per-Million (ppm\text{ppm}) Concentration: The concentration is given as 128.0 ppm128.0\text{ ppm}. Since 1 ppm=1.00 mg/L1\text{ ppm} = 1.00\text{ mg/L}, the mass concentration of CuX2+\ce{Cu^{2+}} is: Concentration of CuX2+=128.0 mg/L\text{Concentration of }\ce{Cu^{2+}} = 128.0\text{ mg/L}
  2. Convert Mass Concentration to Millimolar Concentration (mmol/L\text{mmol/L}): Using the molar mass of copper (M=63.55 g/mol=63.55 mg/mmolM = 63.55\text{ g/mol} = 63.55\text{ mg/mmol}): Molar concentration=128.0 mg/L63.55 mg/mmol≈2.01416 mmol/L\text{Molar concentration} = \frac{128.0\text{ mg/L}}{63.55\text{ mg/mmol}} \approx 2.01416\text{ mmol/L} Rounding to four significant figures gives: Concentration of CuX2+=2.014 mmol/L\text{Concentration of }\ce{Cu^{2+}} = 2.014\text{ mmol/L}

Part (b): Calculating the Required Mass of Disodium EDTA Dihydrate

  1. Determine the Amount of CuX2+\ce{Cu^{2+}} in the Aliquot: The volume of the sample is V=250.0 mL=0.2500 LV = 250.0\text{ mL} = 0.2500\text{ L}. n(CuX2+)=C⋅V=(2.01416×10−3 mol/L)⋅0.2500 L=5.0354×10−4 moln(\ce{Cu^{2+}}) = C \cdot V = (2.01416\times 10^{-3}\text{ mol/L}) \cdot 0.2500\text{ L} = 5.0354\times 10^{-4}\text{ mol}
  2. Apply the Stoichiometry of the Lewis Acid–Base Reaction: CuX2+\ce{Cu^{2+}} acts as an electron-pair acceptor (Lewis acid) and the hexadentate ligand EDTAX4−\ce{EDTA^{4-}} acts as an electron-pair donor (Lewis base). They react in a 1:11:1 stoichiometric ratio: CuX2+(aq)+EDTAX4−(aq)→[Cu(EDTA)]X2−(aq)\ce{Cu^{2+}(aq) + EDTA^{4-}(aq) -> [Cu(EDTA)]^{2-}(aq)} Therefore, the stoichiometric amount of NaX2HX2EDTA ⋅2 HX2O\ce{Na2H2EDTA \cdot 2H2O} required equals the moles of CuX2+\ce{Cu^{2+}}: n(NaX2HX2EDTA ⋅2 HX2O)=n(CuX2+)=5.0354×10−4 moln(\ce{Na2H2EDTA \cdot 2H2O}) = n(\ce{Cu^{2+}}) = 5.0354\times 10^{-4}\text{ mol}
  3. Convert Moles to Mass in Milligrams: Using the molar mass of NaX2HX2EDTA ⋅2 HX2O\ce{Na2H2EDTA \cdot 2H2O} (M=372.24 g/molM = 372.24\text{ g/mol}): Mass=(5.0354×10−4 mol)⋅(372.24 g/mol)≈0.18744 g\text{Mass} = (5.0354\times 10^{-4}\text{ mol}) \cdot (372.24\text{ g/mol}) \approx 0.18744\text{ g} Expressing this mass in milligrams: Mass=0.18744 g⋅103 mg/g≈187.4 mg\text{Mass} = 0.18744\text{ g} \cdot 10^3\text{ mg/g} \approx 187.4\text{ mg}

Common Pitfall: Always verify the formula of the EDTA salt provided. EDTA is typically supplied as the disodium dihydrate salt (NaX2HX2EDTA ⋅2 HX2O\ce{Na2H2EDTA \cdot 2H2O}), which has a molar mass of 372.24 g/mol372.24\text{ g/mol}, distinct from free acid HX4EDTA\ce{H4EDTA} (292.24 g/mol292.24\text{ g/mol}).

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student calculates the mass of EDTA required for an entire 1.00 L solution instead of accounting for the 250.0 mL aliquot.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    128.0 ppm=128.0 mg/L  ⟹  c(CuX2+)=128.0 mg/L63.55 mg/mmol=2.014 mmol/L128.0\text{ ppm} = 128.0\text{ mg/L} \implies c(\ce{Cu^2+}) = \frac{128.0\text{ mg/L}}{63.55\text{ mg/mmol}} = 2.014\text{ mmol/L}

  2. Step 2

    n(CuX2+) in 1 L=2.014 mmol  ⟹  n(NaX2HX2EDTA ⋅ 2 HX2O)=2.014 mmoln(\ce{Cu^2+})\text{ in }1\text{ L} = 2.014\text{ mmol} \implies n(\ce{Na2H2EDTA*2H2O}) = 2.014\text{ mmol}

    Correct

    n(CuX2+)=c⋅V=2.01416 mmol/L×0.2500 L=0.50354 mmoln(\ce{Cu^2+}) = c \cdot V = 2.01416\text{ mmol/L} \times 0.2500\text{ L} = 0.50354\text{ mmol}

    You calculated the moles of CuX2+\ce{Cu^2+} present in 1.00 L1.00\text{ L} of solution instead of scaling by the given aliquot volume V=250.0 mL=0.2500 LV = 250.0\text{ mL} = 0.2500\text{ L}.

  3. Step 3

    mass=2.014 mmol×372.24 mg/mmol=749.7 mg\text{mass} = 2.014\text{ mmol} \times 372.24\text{ mg/mmol} = 749.7\text{ mg}

    Correct

    mass=0.50354 mmol×372.24 mg/mmol=187.4 mg\text{mass} = 0.50354\text{ mmol} \times 372.24\text{ mg/mmol} = 187.4\text{ mg}

    Your conversion from millimoles to milligrams using the molar mass of the dihydrate salt was mathematically correct, but the numerical value was four times too large due to the unscaled amount of substance from the previous step.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly related parts-per-million to milligrams per liter using the given solution density.

You accurately computed the concentration in millimoles per liter for part (a).

You recognized the 1:11:1 stoichiometric coordination between the Lewis acid CuX2+\ce{Cu^2+} and the hexadentate ligand EDTA.

You used the correct molar mass for disodium EDTA dihydrate to convert millimoles to milligrams.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omitted aliquot volume scaling

You solved part (b) assuming a 1 L1\text{ L} solution instead of multiplying the concentration by the aliquot volume of 0.2500 L0.2500\text{ L}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated molar concentration directly as the absolute quantity of solute, omitting the n=C×Vn = C \times V scaling step required when working with a specific aliquot volume.

REASONING PATH
Your ACEpath teacher’s suggested approach
Concentration vs. Absolute Amount
  • Molarity (CC) represents solute per liter; total moles (nn) requires multiplying concentration by sample volume: n=C×Vn = C \times V.

  • Always write n=C×Vn = C \times V and substitute the specified aliquot volume before applying stoichiometric equivalence.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate the moles of CuX2+\ce{Cu^2+} in the 250.0 mL250.0\text{ mL} aliquot: n(CuX2+)=2.01416 mmol/L×0.2500 L=0.50354 mmoln(\ce{Cu^2+}) = 2.01416\text{ mmol/L} \times 0.2500\text{ L} = 0.50354\text{ mmol}.

  2. Using the 1:11:1 stoichiometry with EDTA, n(NaX2HX2EDTA ⋅ 2 HX2O)=0.50354 mmoln(\ce{Na2H2EDTA*2H2O}) = 0.50354\text{ mmol}.

  3. Compute the mass of required salt: mass=0.50354 mmol×372.24 mg/mmol≈187.4 mg\text{mass} = 0.50354\text{ mmol} \times 372.24\text{ mg/mmol} \approx 187.4\text{ mg}.

Final answer

187.4 mg

NEXT STEPS
Final Takeaways from Your Teacher
  • Circle the sample volume (250.0 mL250.0\text{ mL}) when first reading the problem prompt to ensure it is not forgotten.

  • Explicitly check that intermediate units are in absolute moles or millimoles rather than concentration units before calculating reagent mass.

OverviewACEpath Teacher's Diagnosis

02 The student misinterprets 1 ppm as 1 g/L rather than 1 mg/L, resulting in a concentration and subsequent mass that are 1000 times too large.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    128.0 ppm=128.0 g/L  ⟹  c(Cu2+)=128.0 g/L63.55 g/mol=2.014 mol/L=2014 mmol/L128.0\text{ ppm} = 128.0\text{ g/L} \implies c(\text{Cu}^{2+}) = \frac{128.0\text{ g/L}}{63.55\text{ g/mol}} = 2.014\text{ mol/L} = 2014\text{ mmol/L}

    Correct

    128.0 ppm=128.0 mg/L  ⟹  c(Cu2+)=128.0 mg/L63.55 g/mol=2.014 mmol/L128.0\text{ ppm} = 128.0\text{ mg/L} \implies c(\text{Cu}^{2+}) = \frac{128.0\text{ mg/L}}{63.55\text{ g/mol}} = 2.014\text{ mmol/L}

    You treated 1 ppm1\text{ ppm} as 1 g/L1\text{ g/L} instead of 1 mg/L1\text{ mg/L}. In dilute aqueous solutions with ρ=1.00 g/mL\rho = 1.00\text{ g/mL}, 1 ppm=1 mg/kg=1 mg/L1\text{ ppm} = 1\text{ mg/kg} = 1\text{ mg/L} because 1 L1\text{ L} of water weighs 106 mg10^6\text{ mg}.

  2. Step 2

    n(Cu2+)=2014 mmol/L×0.2500 L=503.5 mmol  ⟹  n(Na2H2EDTA⋅2H2O)=503.5 mmoln(\text{Cu}^{2+}) = 2014\text{ mmol/L} \times 0.2500\text{ L} = 503.5\text{ mmol} \implies n(\text{Na}_2\text{H}_2\text{EDTA}\cdot 2\text{H}_2\text{O}) = 503.5\text{ mmol}

    Correct

    n(Cu2+)=2.014 mmol/L×0.2500 L=0.5035 mmol  ⟹  n(Na2H2EDTA⋅2H2O)=0.5035 mmoln(\text{Cu}^{2+}) = 2.014\text{ mmol/L} \times 0.2500\text{ L} = 0.5035\text{ mmol} \implies n(\text{Na}_2\text{H}_2\text{EDTA}\cdot 2\text{H}_2\text{O}) = 0.5035\text{ mmol}

    Your application of the 1:11:1 coordination stoichiometry and volume conversion was fully correct, but this step carries over the factor-of-10001000 error from your initial concentration.

  3. Step 3

    mass=503.5 mmol×372.24 mg/mmol=187400 mg\text{mass} = 503.5\text{ mmol} \times 372.24\text{ mg/mmol} = 187400\text{ mg}

    Correct

    mass=0.5035 mmol×372.24 mg/mmol=187.4 mg\text{mass} = 0.5035\text{ mmol} \times 372.24\text{ mg/mmol} = 187.4\text{ mg}

    Your conversion from millimoles to milligrams using the molar mass of the dihydrate salt was set up correctly, but the final numerical value is 10001000 times too large due to the earlier unit error.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that Cu2+\text{Cu}^{2+} and EDTA4−\text{EDTA}^{4-} coordinate in a 1:11:1 stoichiometric ratio as a Lewis acid and Lewis base.

You used the correct molar mass for disodium EDTA dihydrate (372.24 g/mol372.24\text{ g/mol}) rather than anhydrous EDTA.

You correctly multiplied concentration by volume to determine the total molar quantity in the aliquot.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Concentration Unit Conversion Error

You equated 1 ppm1\text{ ppm} to 1 g/L1\text{ g/L} instead of 1 mg/L1\text{ mg/L}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Parts per million (ppm\text{ppm}) represents one part of solute per 10610^6 parts of solution by mass. Because 1 L1\text{ L} of dilute aqueous solution has a mass of approximately 1000 g=106 mg1000\text{ g} = 10^6\text{ mg}, 1 ppm1\text{ ppm} is equivalent to 1 mg/L1\text{ mg/L}, not 1 g/L1\text{ g/L} (which would be 1000 ppm1000\text{ ppm} or parts per thousand).

REASONING PATH
Your ACEpath teacher’s suggested approach
Define ppm for Dilute Aqueous Systems
  • For aqueous solutions where ρ≈1.00 g/mL\rho \approx 1.00\text{ g/mL}, 1 ppm=1 mg/L=1 \mug/mL1\text{ ppm} = 1\text{ mg/L} = 1\text{ \mu g/mL}, while 1 ppb=1 \mug/L1\text{ ppb} = 1\text{ \mu g/L}.

  • Whenever given concentration in ppm\text{ppm}, immediately write down mg/L\text{mg/L} before converting to moles or millimoles.

Quick Sanity Check on Common Lab Concentrations
  • A concentration of 128 g/L128\text{ g/L} represents an extremely dense, concentrated brine (over 10%10\% by mass), whereas industrial effluent trace metals in the ppm range are dilute (<0.1%<0.1\%).

  • Check whether the physical magnitude matches the context of trace contaminant removal.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Express the mass concentration: 128.0 ppm=128.0 mg/L128.0\text{ ppm} = 128.0\text{ mg/L}.

  2. Convert to millimolar concentration: c(Cu2+)=128.0 mg/L63.55 mg/mmol=2.014 mmol/Lc(\text{Cu}^{2+}) = \frac{128.0\text{ mg/L}}{63.55\text{ mg/mmol}} = 2.014\text{ mmol/L}.

  3. Calculate millimoles in 250.0 mL250.0\text{ mL}: n(Cu2+)=2.014 mmol/L×0.2500 L=0.5035 mmoln(\text{Cu}^{2+}) = 2.014\text{ mmol/L} \times 0.2500\text{ L} = 0.5035\text{ mmol}.

  4. Apply 1:11:1 stoichiometry to find the required mass: mass=0.5035 mmol×372.24 mg/mmol=187.4 mg\text{mass} = 0.5035\text{ mmol} \times 372.24\text{ mg/mmol} = 187.4\text{ mg}.

Final answer

(a) 2.014 mmol/L2.014\text{ mmol/L}; (b) 187.4 mg187.4\text{ mg}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice converting between ppm\text{ppm}, ppb\text{ppb}, mg/L\text{mg/L}, and mol/L\text{mol/L} across multiple environmental chemistry problems.

  • Always write explicit unit cancellations when dividing mass concentration by molar mass.

OverviewACEpath Teacher's Diagnosis

03 The student assumes a 1:2 Cu²⁺ to EDTA stoichiometry instead of 1:1, doubling the required mass of EDTA.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    128.0 ppm=128.0 mg/L  ⟹  c(Cu2+)=128.0 mg/L63.55 mg/mmol=2.014 mmol/L128.0\text{ ppm} = 128.0\text{ mg/L} \implies c(\text{Cu}^{2+}) = \frac{128.0\text{ mg/L}}{63.55\text{ mg/mmol}} = 2.014\text{ mmol/L}

  2. Step 2

    n(Cu2+)=2.014 mmol/L×0.2500 L=0.5035 mmoln(\text{Cu}^{2+}) = 2.014\text{ mmol/L} \times 0.2500\text{ L} = 0.5035\text{ mmol}

  3. Step 3

    n(EDTA)=2×n(Cu2+)=1.007 mmoln(\text{EDTA}) = 2 \times n(\text{Cu}^{2+}) = 1.007\text{ mmol}

    Correct

    n(EDTA)=n(Cu2+)=0.5035 mmoln(\text{EDTA}) = n(\text{Cu}^{2+}) = 0.5035\text{ mmol}

    EDTA is a hexadentate ligand that coordinates to transition metal cations in a 1:11:1 stoichiometric ratio to form [Cu(EDTA)]2−[\text{Cu}(\text{EDTA})]^{2-}. The +2+2 charge on Cu2+\text{Cu}^{2+} does not require two EDTA molecules.

  4. Step 4

    mass=1.007 mmol×372.24 mg/mmol=374.8 mg\text{mass} = 1.007\text{ mmol} \times 372.24\text{ mg/mmol} = 374.8\text{ mg}

    Correct

    mass=0.5035 mmol×372.24 mg/mmol=187.4 mg\text{mass} = 0.5035\text{ mmol} \times 372.24\text{ mg/mmol} = 187.4\text{ mg}

    Your mass calculation correctly applied the molar mass of disodium EDTA dihydrate, but it inherited the doubled mole value from the previous step.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly related ppm\text{ppm} to mg/L\text{mg/L} for an aqueous solution.

You converted mass concentration into millimolarity with the proper molar mass and significant figures.

You accurately found the total millimoles of Cu2+\text{Cu}^{2+} in the sample volume.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Stoichiometric Ratio Error in Chelation

You may have matched the 2+2+ charge of copper to a multiplier of 22 for the ligand.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the oxidation state or charge of a central metal ion with the metal-to-ligand coordination stoichiometry when using a polydentate chelating agent.

REASONING PATH
Your ACEpath teacher’s suggested approach
Stoichiometry of EDTA Complexes
  • Because EDTA4−\text{EDTA}^{4-} has six donor atoms (two nitrogens and four carboxylate oxygens), it wraps around a single metal center to form an octahedral complex with a strictly 1:11:1 metal-to-EDTA stoichiometry, regardless of the metal ion's +2+2 or +3+3 charge.

  • Always set n(EDTA)=n(Mn+)n(\text{EDTA}) = n(\text{M}^{n+}) for mononuclear chelate complexes unless a bridging or non-chelating mode is explicitly specified.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Apply the 1:11:1 reaction stoichiometry: Cu2++EDTA4−→[Cu(EDTA)]2−\text{Cu}^{2+} + \text{EDTA}^{4-} \rightarrow [\text{Cu}(\text{EDTA})]^{2-}, so n(EDTA)=n(Cu2+)=0.5035 mmoln(\text{EDTA}) = n(\text{Cu}^{2+}) = 0.5035\text{ mmol}.

  2. Multiply by the molar mass of the disodium dihydrate salt: mass=0.5035 mmol×372.24 mg/mmol=187.4 mg\text{mass} = 0.5035\text{ mmol} \times 372.24\text{ mg/mmol} = 187.4\text{ mg}.

Final answer

(a) 2.014 mmol/L2.014\text{ mmol/L}; (b) 187.4 mg187.4\text{ mg}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review how polydentate ligands (chelates) satisfy the coordination number of a metal ion with a single ligand molecule.

  • Practice identifying the stoichiometric ratio between metal cations and multidentate versus monodentate Lewis bases.

Lock it in

Similar question

01

A water sample contains 54.0 ppm54.0\text{ ppm} of AlX3+\ce{Al^3+} (M=26.98 g/molM = 26.98\text{ g/mol}, 1 ppm=1 mg/L1\text{ ppm} = 1\text{ mg/L}). How many millimoles of AlX3+\ce{Al^3+} are present in a 100.0 mL100.0\text{ mL} aliquot?

Answer

0.200 mmol0.200\text{ mmol}. Step 1: Concentration C=54.0 mg/L26.98 mg/mmol=2.001 mmol/LC = \frac{54.0\text{ mg/L}}{26.98\text{ mg/mmol}} = 2.001\text{ mmol/L}. Step 2: Amount n=C×V=2.001 mmol/L×0.1000 L≈0.200 mmoln = C \times V = 2.001\text{ mmol/L} \times 0.1000\text{ L} \approx 0.200\text{ mmol}.

02

A 500.0 mL500.0\text{ mL} industrial rinse solution contains NiX2+\ce{Ni^2+} at 88.0 ppm88.0\text{ ppm} (M=58.69 g/molM = 58.69\text{ g/mol}). If EDTAX4−\ce{EDTA^4-} binds NiX2+\ce{Ni^2+} in a 1:11:1 ratio, calculate the mass in milligrams of NaX2HX2EDTA ⋅ 2 HX2O\ce{Na2H2EDTA*2H2O} (M=372.24 g/molM = 372.24\text{ g/mol}) required to chelate all nickel ions in this aliquot.

Answer

279 mg279\text{ mg}. Step 1: C(NiX2+)=88.0 mg/L58.69 mg/mmol=1.4994 mmol/LC(\ce{Ni^2+}) = \frac{88.0\text{ mg/L}}{58.69\text{ mg/mmol}} = 1.4994\text{ mmol/L}. Step 2: n=1.4994 mmol/L×0.5000 L=0.7497 mmoln = 1.4994\text{ mmol/L} \times 0.5000\text{ L} = 0.7497\text{ mmol}. Step 3: Mass=0.7497 mmol×372.24 mg/mmol=279.1 mg≈279 mg\text{Mass} = 0.7497\text{ mmol} \times 372.24\text{ mg/mmol} = 279.1\text{ mg} \approx 279\text{ mg}.

03

A 150.0 mL150.0\text{ mL} solution containing FeX3+\ce{Fe^3+} (M=55.85 g/molM = 55.85\text{ g/mol}) requires 111.7 mg111.7\text{ mg} of disodium EDTA dihydrate (M=372.24 g/molM = 372.24\text{ g/mol}) for complete 1:11:1 complexation. Determine the original concentration of FeX3+\ce{Fe^3+} in parts per million (ppm\text{ppm}, where 1 ppm=1 mg/L1\text{ ppm} = 1\text{ mg/L}).

Answer

111.7 ppm111.7\text{ ppm}. Step 1: n(EDTA)=111.7 mg372.24 mg/mmol=0.3001 mmol=n(FeX3+)n(\text{EDTA}) = \frac{111.7\text{ mg}}{372.24\text{ mg/mmol}} = 0.3001\text{ mmol} = n(\ce{Fe^3+}). Step 2: Molarity C=0.3001 mmol0.1500 L=2.0007 mmol/LC = \frac{0.3001\text{ mmol}}{0.1500\text{ L}} = 2.0007\text{ mmol/L}. Step 3: Mass concentration =2.0007 mmol/L×55.85 mg/mmol≈111.7 mg/L=111.7 ppm= 2.0007\text{ mmol/L} \times 55.85\text{ mg/mmol} \approx 111.7\text{ mg/L} = 111.7\text{ ppm}.

Loading workspace…