Resources
A high-pressure containment vessel fitted with an emergency relief valve has a fixed volume of and a certified burst-threshold pressure of . The vessel is charged with of nitrogen gas at an initial temperature of . Calculate the critical boundary temperature in Kelvin () at which the system reaches this maximum allowable pressure limit before the safety valve triggers, assuming ideal gas behavior with .
Answer and steps
Final answer
Steps
Identify the given values at the threshold limit
To determine the critical boundary temperature at which the vessel reaches its maximum allowable pressure, we can use the Ideal Gas Law: where:
- is the pressure of the gas,
- is the volume of the container,
- is the amount of gas in moles,
- is the universal gas constant (),
- is the absolute temperature in Kelvin ().
The problem asks for the temperature when the pressure reaches the burst-threshold limit:
- Target pressure,
- Vessel volume,
- Amount of gas,
- Ideal gas constant,
(Note: The initial temperature of describes the starting state of the system, but since the final state has completely defined values for , , and , we can directly solve for using the ideal gas equation).
Rearrange the Ideal Gas Law to solve for temperature
Rearranging to isolate :
Substitute the known values and calculate
Substitute the given values into the formula:
Calculate the numerator and the denominator:
- Numerator:
- Denominator:
Now, divide the numerator by the denominator:
Rounding to three significant figures to match the given data (, , ):
Alternative Method (Gay-Lussac's Law)
We can also find the initial pressure at : Since volume and moles are constant, pressure and temperature are directly proportional (): Both approaches yield the same threshold temperature of .
Typical errors
01 The student inverted the ideal gas law relationship when solving for temperature, using T = nR / (PV) instead of T = PV / (nR).
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
To isolate in the equation , you must divide both sides by the product , giving rather than inverted as .
- Step 2Correct
Your arithmetic evaluation was carried out correctly according to your formula, but it used the inverted fraction from Step 1.
- Step 3Correct
Because of the inverted relationship in Step 1, your final calculated temperature was the reciprocal of the correct ratio.
WHAT YOU DID WELL
Compliments from Your TeacherYou selected the correct equation of state () for this ideal gas problem.
You correctly identified and substituted the given numeric values for pressure, volume, moles, and the gas constant.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou divided the right-hand factors () by the left-hand factors () instead of dividing both sides by the coefficients multiplying the unknown variable .
REASONING PATH
Your ACEpath teacher’s suggested approach- Isolating a Multiplied Variable
For any relation , dividing both sides by gives .
Circle the target variable first, identify what is multiplying it, and divide the other side of the equal sign by those factors.
- Physical Reality / Units Sanity Check
Heating a rigid gas tank from to increase pressure from to must result in a higher temperature ().
Always check whether the resulting temperature makes physical sense before finalizing your answer; is near absolute zero.
CORRECTED PATH
ACEpath Teacher's DemonstrationStart from the ideal gas law: .
Divide both sides by to isolate : .
Substitute the boundary values: .
Evaluate the numerator and denominator: .
02 The student mistakenly multiplied the denominator terms instead of dividing by both n and R when evaluating on paper or a calculator, computing (P × V / n) × R.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
Because is in the denominator of , you must divide by both and . Multiplying by placed it in the numerator.
- Step 3Correct
Your final calculation followed arithmetically from the misplaced constant in the previous step.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly selected the Ideal Gas Law formula to relate pressure, volume, moles, and temperature.
You accurately solved for the variable symbolically as .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou knew that , but you wrote outside the fraction as a factor rather than keeping it inside the denominator.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisMisinterpreting a compound denominator as during substitution, rather than dividing by the entire grouped product or dividing sequentially by each factor.
REASONING PATH
Your ACEpath teacher’s suggested approach- Grouping compound denominators
For any expression , division applies to both factors: .
Always place parentheses around the entire denominator before entering it into a calculator or writing it out in multi-step arithmetic.
- Physical reasonableness check
Heating a gas increases its pressure when volume and moles are held constant ().
Notice that the initial state is with . To reach , the gas must be heated well above , so is physically impossible.
CORRECTED PATH
ACEpath Teacher's Demonstration03 The student added the initial temperature of 290 K to the calculated temperature, confusing absolute temperature determination with a temperature change (ΔT).
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
Solving with the threshold values already yields the final absolute temperature (). You added the initial temperature of , treating the result as a temperature change () rather than the final state temperature itself.
- Step 3Correct
Your final numerical answer is incorrect due to adding in the previous step.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly recalled and rearranged the ideal gas equation to isolate .
You substituted the correct threshold pressure, volume, moles, and gas constant into the equation.
You accurately evaluated the arithmetic for to obtain .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou treated the temperature obtained directly from the ideal gas law as a temperature change () and added the initial temperature to it.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisThe ideal gas law () is an equation of state that relates the physical properties of a gas at a single, specific state. Evaluating with final state variables gives the final absolute temperature directly, not the temperature increase .
REASONING PATH
Your ACEpath teacher’s suggested approach- Equation of State vs. Process Equation
The ideal gas law defines the absolute temperature of a system at a specific equilibrium state, not the temperature change .
When you substitute final conditions () into , take the resulting value directly as without adding .
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate the threshold temperature directly from the state variables: .
Evaluate the quotient: .
Round to three significant figures to match the given data: .
Lock it in
How do you isolate from the Ideal Gas Law equation ?
. Divide both sides by the factors multiplying ( and ).
Similar question
A sealed cylinder contains of helium gas at a pressure of . Using , calculate the temperature in Kelvin.
Answer
. Rearrange to .
An autoclave with a fixed volume of holds of steam. If the maximum safe operating temperature is , what is the maximum pressure generated in atmospheres? (Use )
Answer
. Rearrange to isolate pressure: .
A rigid canister initially at and is heated until the internal pressure reaches . Assuming constant amount of gas, find the final temperature in Kelvin using either the combined gas law ratio () or by determining moles first.
Answer
. By Gay-Lussac's Law ( constant): .