Resources
An industrial aqueous wastewater sample contains of urea (, molar mass , non-electrolyte) dissolved per of solution. The measured density of this dilute solution at is . Given that pure water has and freezes at , convert the concentration into molality (, in ) by accounting for the exact mass of the solvent, and compute the freezing point depression in millikelvins ().
Answer and steps
Final answer
Molality ; (Freezing Point )
Steps
Calculate the amount (in moles) of solute
Convert the mass of urea from milligrams to grams:
Using the molar mass of urea (), determine the number of moles ():
Determine the exact mass of the solvent
To find molality, the mass of the solvent alone is required, not the mass of the entire solution.
- Calculate the total mass of the solution:
- Subtract the solute mass to find the solvent mass:
- Convert to kilograms:
Common Pitfall: Assuming that of dilute solution contains exactly of water ignores both the measured solution density and the mass occupied by the dissolved solute, leading to slight inaccuracies in precision calculations.
Compute the molality of the solution
Molality () is defined as the moles of solute per kilogram of solvent:
Calculate the freezing point depression ()
Because urea () is a covalent non-electrolyte, it does not dissociate in water, so its van 't Hoff factor is .
Apply the colligative freezing point depression formula:
Since a change of is equivalent to a change of :
The resulting freezing point of the wastewater is:
Typical errors
01 The student confuses molality with molarity by using the volume of solution in liters instead of the mass of solvent in kilograms.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You divided moles by the volume of the solution () rather than the mass of the pure solvent in kilograms. To find the solvent mass, first multiply the solution volume by its density to find the total solution mass, then subtract the solute mass.
- Step 3Correct
Your formula setup is correct, but your numerical result carries forward the incorrect molality value from Step 2.
- Step 4Correct
You converted degrees Celsius to millikelvins correctly, but the value reflects the earlier molality error.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly converted the mass of urea to grams and found the moles of solute.
You correctly identified that urea is a non-electrolyte with a van 't Hoff factor of .
You correctly set up the colligative property formula and converted your final answer to millikelvins.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou divided by solution volume in liters instead of solvent mass in kilograms.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisMolality () requires the mass of the solvent alone in kilograms (), whereas molarity () uses the volume of the entire solution in liters (). When given solution density and volume, you must determine total solution mass and subtract the solute mass to isolate the solvent mass.
REASONING PATH
Your ACEpath teacher’s suggested approach- Molality vs. Molarity Denominators
vs.
Always verify whether the problem asks for molality (, per kilogram of solvent) or molarity (, per liter of solution).
- Finding Solvent Mass from Solution Data
When density and solution volume are given, compute total solution mass first, then subtract solute mass before calculating molality.
CORRECTED PATH
ACEpath Teacher's DemonstrationFind the total mass of the solution: .
Subtract the mass of urea to find the solvent mass: .
Compute the correct molality: .
Calculate the freezing point depression: .
Molality ,
02 The student uses the total mass of the solution as the solvent mass, forgetting to subtract the mass of the solute.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
Molality requires the mass of the solvent alone in kilograms. You divided by the total mass of the solution () rather than subtracting the of urea first to isolate the solvent mass ().
- Step 4Correct
Your freezing point depression formula and unit conversion to millikelvins were set up correctly, but the numerical answer was affected by the incorrect molality from the previous step.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly used density to calculate the total mass of the solution.
You converted milligrams to grams and accurately determined the molar amount of urea.
You applied the colligative freezing point depression relationship and converted degrees Celsius to millikelvins properly.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated the total mass of the solution as the mass of the solvent. Molality () is strictly moles of solute per kilogram of solvent (), not per kilogram of solution.
REASONING PATH
Your ACEpath teacher’s suggested approach- Distinguish Solution vs. Solvent Mass
Always subtract the solute mass from the total solution mass before calculating molality.
- Molality Definition Check
Verify that the denominator contains only kilograms of pure solvent (water), not kilograms of solution.
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate solvent mass: .
Compute molality: .
Calculate freezing point depression: .
Convert to millikelvins: .
,
03 The student correctly calculates the freezing point depression in degrees Celsius but fails to convert it to millikelvins.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3
- Step 4
- Step 5Correct
A temperature difference of equals , and . You relabeled the unit from to without multiplying by .
WHAT YOU DID WELL
Compliments from Your TeacherYou accounted for the measured solution density to find the exact mass of the solvent instead of assuming .
You correctly calculated the moles of urea and the molality of the solution.
You correctly applied the freezing point depression formula with .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou replaced the unit symbol with millikelvins () without multiplying the numerical value by .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou recognized that in degrees Celsius is identical to in kelvins, but overlooked the SI prefix 'milli-' (), which requires multiplying by .
REASONING PATH
Your ACEpath teacher’s suggested approach- Temperature Interval Equivalence
First convert a temperature change directly to kelvins before applying metric prefixes.
- SI Prefix Scaling
Multiply by when converting from to .
CORRECTED PATH
ACEpath Teacher's DemonstrationRecognize that a temperature change of equals .
Convert from kelvins to millikelvins using the conversion factor : .
Round to three or four significant figures as appropriate: .
;
Lock it in
What is the exact definition and formula for molality (), and how does its denominator differ from molarity ()?
Molality is . Its denominator accounts only for the solvent mass, whereas molarity () divides by the total volume of solution in liters.
Similar question
A sample contains of glucose (, molar mass ) dissolved in of water. Calculate the molality of the solution and the freezing point depression given .
Answer
; (). Steps: ; ; ; .
An aqueous solution is prepared by dissolving of (molar mass , assume ) in water to make of solution. The measured density of the solution is . Determine the molality of and the resulting freezing point depression ().
Answer
; . Steps: ; ; ; ; .
A aqueous solution of a non-volatile non-electrolyte solute freezes at (). If the solution has a density of and contains of solute per of solution, find the molar mass of the solute.
Answer
Molar mass . Steps: ; ; moles of solute ; molar mass .