Resources
An industrial wastewater stream contains dissolved lead(II) nitrate, , at a measured concentration of . Assuming the wastewater has a solution density of , calculate the concentration of elemental lead () in the wastewater expressed in parts per million (, equivalent to ) by utilizing the mass fraction of lead in . Use molar masses: , , and . Express your answer to four significant figures.
Answer and steps
Final answer
Steps
Calculate the molar mass of
To find the concentration of elemental lead () in parts per million (), we determine the fraction of lead present in lead(II) nitrate, use it to find the mass of lead per liter, and then convert this value relative to the mass of the solution.
Using the provided atomic molar masses:
Multiply each element by the number of atoms in one formula unit of :
Determine the mass fraction of lead ()
The mass fraction represents the proportion of the compound's total mass contributed by lead:
Calculate the concentration of lead in
Multiply the concentration of dissolved by the mass fraction of lead:
Convert to parts per million ()
By definition:
Using the wastewater density of :
Since has a mass of exactly , a concentration in is numerically identical to :
Rounded to four significant figures, the concentration is .
Typical errors
01 The student forgets to distribute the subscript 2 outside the parentheses to the oxygen atoms in Pb(NO₃)₂, calculating the molar mass using only 3 oxygen atoms instead of 6.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
When distributing the subscript outside the parentheses to the nitrate group , you must multiply the subscript of oxygen by , yielding oxygen atoms rather than .
- Step 2Correct
Your formula for mass fraction was set up correctly, but the result is affected by the incorrect molar mass from Step 1.
- Step 3Correct
You correctly multiplied the compound's concentration by the mass fraction, but the numerical value inherits the previous error.
- Step 4Correct
Your density conversion and final definition of as are completely sound, but the final value carries through the earlier calculation error.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly recognized that the mass fraction of lead is found by dividing the atomic mass of lead by the formula molar mass.
You correctly related solution concentration and density to convert from milligrams per liter to parts per million.
You maintained proper significant figures throughout your multi-step calculations.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeIn Step 1, you multiplied nitrogen's atomic mass by , but wrote instead of for oxygen.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou neglected to multiply the inner subscript of oxygen () by the outer subscript () when expanding the polyatomic ion formula unit .
REASONING PATH
Your ACEpath teacher’s suggested approach- Distribute Subscripts Across Parentheses
For any chemical formula containing , the total count of atom in one formula unit is .
Always write out the expanded atom count before substituting molar masses (for example, ).
CORRECTED PATH
ACEpath Teacher's Demonstration02 The student misinterprets the nitrate formula as containing only 1 nitrogen and 1 oxygen atom, omitting the subscript 3 on oxygen when calculating the molar mass.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You calculated the nitrate group with only one oxygen atom instead of three. A nitrate ion () contains oxygen atoms, so each unit has , giving a total of oxygen atoms in .
- Step 2Correct
You set up the ratio of lead's atomic mass to the compound's total molar mass correctly, but the result was affected by the incorrect molar mass from Step 1.
- Step 3Correct
Your method of multiplying the total salt concentration by the elemental mass fraction was correct, but the numerical result carried forward the earlier error.
- Step 4Correct
You correctly reasoned that with a density of , equals (), but the final numerical value remains affected by the initial molar mass calculation.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified the formula for calculating elemental mass fraction as the atomic mass of lead divided by the total molar mass of the compound.
You properly applied the mass fraction to determine the concentration of dissolved lead in milligrams per liter.
You correctly used the solution density to show that milligrams per liter is equivalent to parts per million.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou wrote inside the parentheses instead of , leaving out the subscript on oxygen in .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisOverlooking internal subscripts of polyatomic ions when distributing outer parentheses during molar mass summation.
REASONING PATH
Your ACEpath teacher’s suggested approach- Count Total Atoms First
For a formula unit , multiply the outside subscript by each inside subscript: total and total .
Write out the atom inventory explicitly before summing molar masses (e.g., has , , and ).
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate the correct molar mass: .
Recalculate the mass fraction of : .
Multiply the mass fraction by the concentration: .
Convert to parts per million using the solution density (): .
03 The student divides the concentration by the mass fraction instead of multiplying it, incorrectly yielding a lead concentration greater than the total lead nitrate concentration.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
You divided by the mass fraction instead of multiplying. Since lead makes up roughly of lead(II) nitrate, each liter contains of lead. Dividing yields , which is impossible because the mass of a component cannot exceed the mass of the whole compound.
- Step 4Correct
Your reasoning that makes equivalent to is sound, but the numerical answer inherits the division error from the previous step.
WHAT YOU DID WELL
Compliments from Your TeacherYou calculated the molar mass of accurately from the given atomic weights.
You correctly defined the mass fraction of lead as the atomic mass of lead divided by the compound's molar mass.
You recognized that with a solution density of , a concentration in corresponds directly to .
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated the mass fraction as a divisor rather than a multiplying factor when converting from whole compound mass to constituent elemental mass.
REASONING PATH
Your ACEpath teacher’s suggested approach- Sanity check part vs. whole
The mass of an element within a compound must always be strictly less than the total mass of the compound.
Whenever you compute the amount of an element inside a sample, multiply the sample mass by the mass fraction: . Always check that the resulting value is smaller than the original sample mass.
CORRECTED PATH
ACEpath Teacher's DemonstrationMultiply the total compound concentration by the mass fraction: .
Convert to parts per million using the solution density: with , .
Lock it in
How do you determine the total number of atoms of element in the formula unit ?
Multiply the inner subscript of by the outer subscript: atoms of .
Similar question
Calculate the molar mass of magnesium nitrate, , using atomic masses: , , and . Express your answer to three decimal places.
Answer
. Key steps: .
An aqueous sample contains dissolved copper(II) nitrate, , at a concentration of . What is the concentration of elemental copper () in ? (Molar masses: , , )
Answer
. Key steps: Molar mass of . Mass fraction of . Concentration of .
A contaminated soil leachate has an iron(III) sulfate, , concentration of and a density of . Calculate the concentration of elemental iron () in parts per million (). (Molar masses: , , )
Answer
. Key steps: Formula has , , and . Molar mass of . Mass fraction of . Concentration in .