Resources

An analytical chemist measures the pH\text{pH} of an aqueous solution of chloric acid, HClO3\text{HClO}_3 (a strong monoprotic acid), to be 2.152.15 at 25∘C25^\circ\text{C}. To prepare exactly 750.0 mL750.0\text{ mL} of this target solution from a concentrated stock solution of 1.75 M HClO31.75\text{ M}\text{ HClO}_3, what volume (in milliliters, mL\text{mL}) of the concentrated stock solution must be measured and diluted with water?

Answer and steps

Final answer

3.03 mL3.03\text{ mL}

Steps

01

Determine the hydronium ion concentration in the target solution

To find the required volume of the concentrated stock solution, we first determine the molarity of the target solution using its pH\text{pH}, and then apply the dilution equation.

Chloric acid (HClOX3\ce{HClO3}) is a strong monoprotic acid, meaning it dissociates completely in water:

HClOX3(aq)→HX+(aq)+ClOX3X−(aq)\ce{HClO3(aq) -> H+(aq) + ClO3-(aq)}

Because each mole of HClOX3\ce{HClO3} produces one mole of HX+\ce{H+}, the concentration of the acid is equal to the concentration of hydronium ions:

[HClOX3]dilute=[HX+][\ce{HClO3}]_{\text{dilute}} = [\ce{H+}]

Using the definition of pH\text{pH}:

pH=−log⁡10[HX+]\text{pH} = -\log_{10}[\ce{H+}]

[HX+]=10−pH=10−2.15 M≈7.0795×10−3 M[\ce{H+}] = 10^{-\text{pH}} = 10^{-2.15}\text{ M} \approx 7.0795 \times 10^{-3}\text{ M}

Thus, the target concentration is:

M2=7.0795×10−3 MM_2 = 7.0795 \times 10^{-3}\text{ M}


02

Use the dilution equation to calculate the required volume of stock solution

The number of moles of solute remains constant during dilution:

M1V1=M2V2M_1 V_1 = M_2 V_2

Where:

  • M1=1.75 MM_1 = 1.75\text{ M} (concentration of concentrated stock)
  • V1V_1 is the volume of stock solution needed
  • M2=7.0795×10−3 MM_2 = 7.0795 \times 10^{-3}\text{ M} (concentration of diluted solution)
  • V2=750.0 mLV_2 = 750.0\text{ mL} (final volume of diluted solution)

Rearranging for V1V_1:

V1=M2⋅V2M1V_1 = \frac{M_2 \cdot V_2}{M_1}

Substitute the values:

V1=(7.0795×10−3 M)⋅(750.0 mL)1.75 M≈5.30961.75 mL≈3.03 mLV_1 = \frac{(7.0795 \times 10^{-3}\text{ M}) \cdot (750.0\text{ mL})}{1.75\text{ M}} \approx \frac{5.3096}{1.75}\text{ mL} \approx 3.03\text{ mL}

Common Pitfall: When working with logarithmic scales like pH\text{pH}, remember that the digits after the decimal point represent the significant figures of the resulting concentration. Avoid rounding too early during the intermediate step ([HX+][\ce{H+}] calculation) to prevent rounding errors in the final volume.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student calculates hydronium ion concentration as -log(pH) instead of using the inverse logarithm 10^(-pH), leading to an unphysical concentration and volume.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    [H+]=−log⁡(2.15)=−0.332 M  ⟹  [HClO3]=0.332 M[\text{H}^+] = -\log(2.15) = -0.332\text{ M} \implies [\text{HClO}_3] = 0.332\text{ M}

    Correct

    [H+]=10−pH=10−2.15 M≈7.08×10−3 M[\text{H}^+] = 10^{-\text{pH}} = 10^{-2.15}\text{ M} \approx 7.08 \times 10^{-3}\text{ M}

    You applied the −log⁡-\log operation to pH\text{pH} instead of taking the inverse base-10 logarithm. By definition, pH=−log⁡10[H+]\text{pH} = -\log_{10}[\text{H}^+], which rearranges to [H+]=10−pH[\text{H}^+] = 10^{-\text{pH}}.

  2. Step 2

    C1V1=C2V2  ⟹  (1.75 M)(V1)=(0.332 M)(750.0 mL)  ⟹  V1=0.332×750.01.75=142 mLC_1 V_1 = C_2 V_2 \implies (1.75\text{ M})(V_1) = (0.332\text{ M})(750.0\text{ mL}) \implies V_1 = \frac{0.332 \times 750.0}{1.75} = 142\text{ mL}

    Correct

    V1=C2V2C1=(7.0795×10−3 M)(750.0 mL)1.75 M≈3.03 mLV_1 = \frac{C_2 V_2}{C_1} = \frac{(7.0795 \times 10^{-3}\text{ M})(750.0\text{ mL})}{1.75\text{ M}} \approx 3.03\text{ mL}

    Your algebraic manipulation and substitution into the dilution formula C1V1=C2V2C_1 V_1 = C_2 V_2 were executed properly, but the result was affected by the incorrect concentration value from Step 1.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly recognized that chloric acid is a strong monoprotic acid whose concentration equals [H+][\text{H}^+].

You selected and rearranged the appropriate dilution equation C1V1=C2V2C_1 V_1 = C_2 V_2 to solve for the stock volume.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverse Logarithm vs. Logarithm Error

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused finding pH\text{pH} from [H+][\text{H}^+] (which takes −log⁡[H+]-\log[\text{H}^+]) with finding [H+][\text{H}^+] from pH\text{pH} (which requires taking 10−pH10^{-\text{pH}}). When this produced a negative value, you dropped the negative sign rather than revisiting the inverse operation.

REASONING PATH
Your ACEpath teacher’s suggested approach
Converting pH to Ion Concentration
  • pH=−log⁡10[H+]  ⟺  [H+]=10−pH\text{pH} = -\log_{10}[\text{H}^+] \iff [\text{H}^+] = 10^{-\text{pH}}

  • Always raise 1010 to the negative of the pH\text{pH} value. A concentration must always be positive and will be much smaller than 1 M1\text{ M} whenever pH>0\text{pH} > 0.

Sanity Check on Calculated Concentration
  • Molar concentrations are physical quantities that cannot be negative.

  • If a concentration formula yields a negative number, stop and re-examine the logarithmic identity instead of taking the absolute value.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. [H+]=10−2.15 M≈7.0795×10−3 M[\text{H}^+] = 10^{-2.15}\text{ M} \approx 7.0795 \times 10^{-3}\text{ M}

  2. Because HClO3\text{HClO}_3 is strong and monoprotic, C2=[H+]≈7.0795×10−3 MC_2 = [\text{H}^+] \approx 7.0795 \times 10^{-3}\text{ M}.

  3. V1=C2⋅V2C1=(7.0795×10−3 M)(750.0 mL)1.75 M=3.034 mLV_1 = \frac{C_2 \cdot V_2}{C_1} = \frac{(7.0795 \times 10^{-3}\text{ M})(750.0\text{ mL})}{1.75\text{ M}} = 3.034\text{ mL}

Final answer

3.03 mL3.03\text{ mL}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the exponential identity y=−log⁡10(x)  ⟹  x=10−yy = -\log_{10}(x) \implies x = 10^{-y} so you naturally reach for the power function when moving from pH\text{pH} to concentration.

  • Practice working through strong acid dilution problems where pH\text{pH} is given as the starting target concentration.

OverviewACEpath Teacher's Diagnosis

02 The student misarranges the dilution formula as V₁ = (C₁V₂)/C₂, multiplying the stock concentration by the target volume instead of dividing by it.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    [H+]=10−2.15=7.08×10−3 M  ⟹  C2=7.08×10−3 M[\text{H}^+] = 10^{-2.15} = 7.08 \times 10^{-3}\text{ M} \implies C_2 = 7.08 \times 10^{-3}\text{ M}

  2. Step 2

    V1=C1×V2C2  ⟹  V1=1.75 M×750.0 mL7.08×10−3 MV_1 = \frac{C_1 \times V_2}{C_2} \implies V_1 = \frac{1.75\text{ M} \times 750.0\text{ mL}}{7.08 \times 10^{-3}\text{ M}}

    Correct

    C1V1=C2V2  ⟹  V1=C2V2C1=(7.08×10−3 M)(750.0 mL)1.75 MC_1 V_1 = C_2 V_2 \implies V_1 = \frac{C_2 V_2}{C_1} = \frac{(7.08 \times 10^{-3}\text{ M})(750.0\text{ mL})}{1.75\text{ M}}

    You inverted the concentration ratio when solving for V1V_1. To isolate V1V_1 in C1V1=C2V2C_1 V_1 = C_2 V_2, you must divide both sides by the stock concentration C1C_1, which places C1C_1 in the denominator.

  3. Step 3

    V1=1.85×105 mLV_1 = 1.85 \times 10^5\text{ mL}

    Correct

    V1≈3.03 mLV_1 \approx 3.03\text{ mL}

    Your arithmetic follows your algebraic setup, but because the formula was rearranged incorrectly, the final volume is off by several orders of magnitude.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used the logarithmic relationship [H+]=10−pH[\text{H}^+] = 10^{-\text{pH}} to find the target solution's concentration.

You correctly identified that for a strong monoprotic acid like HClOX3\ce{HClO3}, the acid molarity equals [H+][\text{H}^+].

You selected the appropriate dilution principle relating initial and final moles.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Dilution Formula Inversion

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You algebraically misarranged the dilution equation C1V1=C2V2C_1 V_1 = C_2 V_2, multiplying by the concentrated stock molarity and dividing by the dilute target molarity instead of dividing by the stock molarity.

REASONING PATH
Your ACEpath teacher’s suggested approach
Isolate the Target Variable Using Inverse Operations
  • When rearranging C1V1=C2V2C_1 V_1 = C_2 V_2 for V1V_1, divide both sides by C1C_1 to yield V1=C2V2C1V_1 = \frac{C_2 V_2}{C_1}.

  • Write out the full equality C1V1=C2V2C_1 V_1 = C_2 V_2 first, then divide both sides by C1C_1 explicitly before substituting numbers.

Physical Sanity Check for Dilution
  • Dilution requires adding solvent to a concentrated stock, so the stock volume needed (V1V_1) must always be significantly smaller than the final volume (V2V_2).

  • Compare V1V_1 to V2V_2: if V1>V2V_1 > V_2, check whether your concentration terms were flipped in the fraction.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. State the conservation of moles during dilution: C1V1=C2V2C_1 V_1 = C_2 V_2

  2. Divide both sides by the concentrated stock molarity C1C_1: V1=C2V2C1V_1 = \frac{C_2 V_2}{C_1}

  3. Substitute the values: V1=(7.0795×10−3 M)(750.0 mL)1.75 MV_1 = \frac{(7.0795 \times 10^{-3}\text{ M})(750.0\text{ mL})}{1.75\text{ M}}

  4. Evaluate the volume: V1≈3.03 mLV_1 \approx 3.03\text{ mL}

Final answer

3.03 mL3.03\text{ mL}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always write out C1V1=C2V2C_1 V_1 = C_2 V_2 and perform algebraic cancellation explicitly before entering numbers.

  • Perform a quick order-of-magnitude reality check: preparing 750 mL750\text{ mL} of dilute acid should never require 185 L185\text{ L} (1.85×105 mL1.85 \times 10^5\text{ mL}) of concentrated stock.

OverviewACEpath Teacher's Diagnosis

03 The student incorrectly calculates hydronium ion concentration using natural logarithm base e instead of base 10 (e^(-pH)), underestimating the required stock volume.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    [H+]=e−2.15=0.116 M  ⟹  [HClO3]=0.116 M[\text{H}^+] = e^{-2.15} = 0.116\text{ M} \implies [\text{HClO}_3] = 0.116\text{ M}

    Correct

    [H+]=10−pH=10−2.15 M≈7.08×10−3 M  ⟹  [HClO3]≈7.08×10−3 M[\text{H}^+] = 10^{-\text{pH}} = 10^{-2.15}\text{ M} \approx 7.08 \times 10^{-3}\text{ M} \implies [\text{HClO}_3] \approx 7.08 \times 10^{-3}\text{ M}

    You calculated [H+][\text{H}^+] using e−pHe^{-\text{pH}} instead of 10−pH10^{-\text{pH}}. Because pH\text{pH} is defined using the common logarithm (extbase10 ext{base } 10), its inverse is 10−pH10^{-\text{pH}}.

  2. Step 2

    C1V1=C2V2  ⟹  (1.75 M)(V1)=(0.116 M)(750.0 mL)  ⟹  V1=0.116×750.01.75=49.7 mLC_1V_1 = C_2V_2 \implies (1.75\text{ M})(V_1) = (0.116\text{ M})(750.0\text{ mL}) \implies V_1 = \frac{0.116 \times 750.0}{1.75} = 49.7\text{ mL}

    Correct

    C1V1=C2V2  ⟹  (1.75 M)(V1)=(7.0795×10−3 M)(750.0 mL)  ⟹  V1≈3.03 mLC_1V_1 = C_2V_2 \implies (1.75\text{ M})(V_1) = (7.0795 \times 10^{-3}\text{ M})(750.0\text{ mL}) \implies V_1 \approx 3.03\text{ mL}

    You correctly applied the dilution formula and solved for V1V_1, but the result was thrown off by the incorrect concentration carried over from the first step.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly recognized that chloric acid is a strong monoprotic acid whose concentration equals [H+][\text{H}^+].

You selected and correctly rearranged the dilution formula C1V1=C2V2C_1V_1 = C_2V_2.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Logarithm Base Confusion

You wrote the base of the exponential as ee instead of 1010.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused the common logarithm (base 1010, used in pH=−log⁡10[H+]\text{pH} = -\log_{10}[\text{H}^+]) with the natural logarithm (base ee, used in ln⁡\ln). Converting pH\text{pH} back to concentration requires using 10−pH10^{-\text{pH}}, not e−pHe^{-\text{pH}}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Logarithm Base for pH
  • pH=−log⁡10[H+]\text{pH} = -\log_{10}[\text{H}^+], so [H+]=10−pH[\text{H}^+] = 10^{-\text{pH}}.

  • Whenever you undo pH\text{pH} or pOH\text{pOH}, raise 1010 to the negative value on your calculator (10x10^x), never the exe^x key.

Magnitude Sanity Check
  • A pH\text{pH} of 2.152.15 lies between 22 and 33, meaning [H+][\text{H}^+] must be between 10−2 M10^{-2}\text{ M} (0.01 M0.01\text{ M}) and 10−3 M10^{-3}\text{ M} (0.001 M0.001\text{ M}).

  • Verify that your calculated concentration fits within the order-of-magnitude bounds set by the integer portion of the pH\text{pH}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Find the true target concentration: [H+]=10−2.15 M≈7.0795×10−3 M[\text{H}^+] = 10^{-2.15}\text{ M} \approx 7.0795 \times 10^{-3}\text{ M}.

  2. Equate with acid concentration: C2=[HClO3]=7.0795×10−3 MC_2 = [\text{HClO}_3] = 7.0795 \times 10^{-3}\text{ M}.

  3. Substitute into the dilution formula: V1=C2V2C1=(7.0795×10−3 M)(750.0 mL)1.75 M≈3.03 mLV_1 = \frac{C_2 V_2}{C_1} = \frac{(7.0795 \times 10^{-3}\text{ M})(750.0\text{ mL})}{1.75\text{ M}} \approx 3.03\text{ mL}.

Final answer

3.03 mL3.03\text{ mL}

NEXT STEPS
Final Takeaways from Your Teacher
  • Memorize that the prefix 'p' always denotes −log⁡10-\log_{10}, so inverse 'p' is always 10−x10^{-x}.

  • Practice using your calculator's 10x10^x function rather than exe^x when working with pH\text{pH}, pOH\text{pOH}, pKa\text{p}K_a, and pKb\text{p}K_b.

Lock it in

Similar question

01

A chemist needs to prepare 500.0 mL500.0\text{ mL} of an aqueous HNO3\text{HNO}_3 solution with a pH\text{pH} of 1.801.80. How many milliliters of a 2.50 M HNO32.50\text{ M}\text{ HNO}_3 stock solution are required?

Answer

Step 1: [H+]=10−1.80≈1.585×10−2 M[\text{H}^+] = 10^{-1.80} \approx 1.585 \times 10^{-2}\text{ M}. Step 2: Use M1V1=M2V2  ⟹  (2.50 M)V1=(1.585×10−2 M)(500.0 mL)  ⟹  V1≈3.17 mLM_1 V_1 = M_2 V_2 \implies (2.50\text{ M})V_1 = (1.585 \times 10^{-2}\text{ M})(500.0\text{ mL}) \implies V_1 \approx 3.17\text{ mL}.

02

An environmental sample has a pH\text{pH} of 3.453.45. What volume (in mL\text{mL}) of 0.625 M HClO40.625\text{ M}\text{ HClO}_4 stock solution is needed to create 1.20 L1.20\text{ L} of a standard solution matching this sample's pH\text{pH}?

Answer

Step 1: Target concentration C2=10−3.45≈3.548×10−4 MC_2 = 10^{-3.45} \approx 3.548 \times 10^{-4}\text{ M}. Step 2: V2=1200 mLV_2 = 1200\text{ mL}. Step 3: V1=C2V2C1=(3.548×10−4 M)(1200 mL)0.625 M≈0.681 mLV_1 = \frac{C_2 V_2}{C_1} = \frac{(3.548 \times 10^{-4}\text{ M})(1200\text{ mL})}{0.625\text{ M}} \approx 0.681\text{ mL}.

03

A student dilutes 4.50 mL4.50\text{ mL} of a concentrated monoprotic strong acid stock solution (3.00 M3.00\text{ M}) with pure water to a final volume of 2.00 L2.00\text{ L}. What is the pH\text{pH} of the resulting diluted solution?

Answer

Step 1: Find diluted concentration M2=M1V1V2=(3.00 M)(0.00450 L)2.00 L=6.75×10−3 MM_2 = \frac{M_1 V_1}{V_2} = \frac{(3.00\text{ M})(0.00450\text{ L})}{2.00\text{ L}} = 6.75 \times 10^{-3}\text{ M}. Step 2: Calculate pH=−log⁡10(6.75×10−3)≈2.17\text{pH} = -\log_{10}(6.75 \times 10^{-3}) \approx 2.17.

Loading workspace…