Resources
A manufacturing process for titanium dioxide (, molar mass ) uses the sulfate route. In an industrial batch, of ilmenite ore containing iron(II) titanate (, molar mass ) reacts with of concentrated sulfuric acid (, molar mass ) and of water to produce of purified pigment. All unreacted reactants, auxiliary chemicals, and waste products are discarded. Calculate the Process Mass Intensity (PMI) of this manufacturing operation to three significant figures, and determine the corresponding Environmental Factor (-factor) under these exact operating inputs.
Answer and steps
Final answer
,
Steps
Identify the Relevant Mass Inputs
In green chemistry metrics, Process Mass Intensity (PMI) measures the efficiency of a process by comparing the mass of materials used to the mass of the final isolated product:
From the problem statement, the reaction uses:
- Active reactant from ilmenite ore ():
- Concentrated sulfuric acid ():
- Process water:
Summing the active process chemical inputs:
The mass of the desired product () obtained is:
Calculate the Process Mass Intensity (PMI)
Substitute the total input mass and product mass into the PMI formula:
(Note: Depending on intermediate rounding conventions, ; the batch specification yields .)
Calculate the Environmental Factor (-factor)
The Environmental Factor (-factor) is defined as the total mass of waste generated per unit mass of product:
By conservation of mass, all input mass that does not end up in the desired product becomes waste:
Thus:
Alternatively, using the direct fundamental relation between PMI and -factor:
Typical errors
01 The student excludes water from the total mass of input materials when defining PMI and calculating waste.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You omitted the of water from the process mass calculation and did not account for the active content in the ore (). By definition, PMI includes all process inputs, particularly water and solvents.
- Step 2Correct
You applied the correct definition , but the numerical value was affected by the input mass error from Step 1.
- Step 3Correct
You correctly used mass balance (total input minus isolated product) to find waste mass, but your result propagated the incorrect total input mass.
- Step 4Correct
Your formula for the -factor (as well as the relationship ) was executed correctly, but the resulting value reflects the earlier input mass error.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly defined Process Mass Intensity as the ratio of total input mass to desired product mass.
You used the conservation of mass principle properly to deduce the waste mass from total input minus product mass.
You preserved the direct relationship in your final calculations.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou left out the of process water when tallying total input mass.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated green chemistry mass balance as including only dry chemical reagents or stoichiometry reactants, overlooking that PMI explicitly accounts for all auxiliary materials, solvents, and water used throughout the manufacturing cycle.
REASONING PATH
Your ACEpath teacher’s suggested approach- PMI Input Scope Rule
Always list every mass input specified in the process description—including water, wash solvents, and acids—before dividing by product mass.
- Purity and Active Feed Check
Check whether raw feedstocks (like mineral ores) require adjusting to active chemical component mass when specified by the batch recipe.
CORRECTED PATH
ACEpath Teacher's DemonstrationDetermine active reactant: .
Sum all input streams: .
Compute .
Compute waste mass: .
Compute (or ).
,
02 The student uses only the mass of the active reactive component (50.0% FeTiO3 in ore) instead of the total input mass of raw ore.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You multiplied the ore mass by its purity to isolate the active reactant . However, Process Mass Intensity (PMI) measures the total mass of all raw materials introduced into the manufacturing operation. Because the non-reactive gangue in the ore enters the process and becomes solid waste, the entire of ilmenite ore must be included in the total input mass.
- Step 2Correct
You correctly divided total input mass by product mass, but your numerical result was affected by the omitted of raw ore from Step 1.
- Step 3Correct
You correctly used the fundamental relationship , but this value was affected by the earlier input mass error.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified that PMI is defined as the ratio of total process material inputs to desired isolated product mass.
You correctly applied the mathematical relationship between Process Mass Intensity and the Environmental Factor ().
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeThis is a conceptual error rather than an arithmetic slip, as you treated the green chemistry metric as a stoichiometric calculation rather than a total mass accounting metric.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou confused active stoichiometric reagent mass with the gross raw material input mass required by green chemistry metrics. PMI assesses the overall resource efficiency of a manufacturing process; therefore, any raw material crossing the plant boundary—including unreacted minerals, gangue, solvents, and process water—must be counted in the numerator.
REASONING PATH
Your ACEpath teacher’s suggested approach- Process Boundary Rule
Always sum the gross mass of every raw feed as weighed into the reactor, never deducting impurities, gangue, or unreacted fractions beforehand.
- E-Factor Consistency
Verify that total waste equals total gross mass in minus desired product mass out.
CORRECTED PATH
ACEpath Teacher's DemonstrationInclude the entire of ilmenite ore alongside the acid and water: .
Calculate the Process Mass Intensity: .
Calculate the Environmental Factor: (or ).
,
03 The student confuses the definition of E-factor with PMI, dividing the total input mass instead of the waste mass by the product mass.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You correctly recognized that is the ratio of input mass to product mass. However, you used the full of unrefined ore instead of multiplying by to account for the actual reactant mass ( of ). This made your total input mass instead of , giving an inflated of instead of .
- Step 2Correct
You used the formula for Process Mass Intensity () to calculate the -factor. The -factor measures waste generated per unit product, so its numerator must be the mass of waste (), which simplifies to .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified the general mathematical structure of green chemistry mass metrics as ratios relative to the mass of the final isolated product.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou used the gross ore mass without adjusting for the stated 50.0% active FeTiO3 purity.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated the Environmental Factor (E-factor) as identical to Process Mass Intensity (PMI), failing to subtract the mass of product from the numerator to isolate total waste.
REASONING PATH
Your ACEpath teacher’s suggested approach- Accounting for reactant purity in input mass
When raw feedstocks specify a purity percentage, only the active chemical component entering the reaction sequence is counted in the process mass inputs.
Multiply the raw material mass by its purity percentage before adding it to other process inputs.
- Distinguishing PMI from E-factor
, whereas .
Subtract the product mass from the total input mass to obtain the waste mass, or simply subtract from your calculated PMI.
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate the active reactant mass: .
Sum all active process inputs: .
Compute Process Mass Intensity: .
Determine total waste: .
Compute Environmental Factor: .
,
Lock it in
Does Process Mass Intensity (PMI) include process water and organic solvents?
Yes. PMI is defined as , which includes reagents, catalysts, solvents, and all process water.
Similar question
An active pharmaceutical ingredient (API) synthesis uses of starting materials, of organic solvent, and of water to isolate of pure API. Calculate the PMI and -factor for this process.
Answer
Total input mass . . .
A chemical plant produces of polymer per batch. The process consumes of monomer, of initiator, and of solvent. A green chemistry revision recovers and recycles of solvent so that only of fresh solvent is supplied per batch. Compare the PMI of the original process versus the revised process (counting only fresh input materials).
Answer
Original inputs . Revised fresh inputs .
A catalytic oxidation process claims an -factor of when water is excluded. If producing of purified product generates of chemical waste and requires an additional of aqueous wash water (all discarded), calculate the true comprehensive PMI and -factor including water.
Answer
Total waste . True . True (or ).