Resources

A fully charged lead-acid storage battery operates at 298 K298\text{ K} via the overall discharge reaction: Pb(s)+PbO2(s)+2H2SO4(aq)→2PbSO4(s)+2H2O(l)\text{Pb}(s) + \text{PbO}_2(s) + 2\text{H}_2\text{SO}_4(aq) \rightarrow 2\text{PbSO}_4(s) + 2\text{H}_2\text{O}(l), for which the standard cell potential is E∘=+2.050 VE^\circ = +2.050\text{ V}. An automotive battery contains 1.20 L1.20\text{ L} of sulfuric acid electrolyte, initially at a concentration of 4.50 M H2SO44.50\text{ M}\text{ H}_2\text{SO}_4. The battery delivers a steady current of 6.00 A6.00\text{ A} for 12.0 hours12.0\text{ hours} to power auxiliary vehicle electronics while the engine is off. Assuming both protons dissociate completely and neglecting volume changes, calculate the cell potential EcellE_{\text{cell}} of this single cell at the end of the 12.0-hour12.0\text{-hour} discharge period at 298 K298\text{ K}.

Answer and steps

Final answer

Ecell=+2.032 VE_{\text{cell}} = +2.032\text{ V}

Steps

01

Calculate the Total Charge Passed and Moles of Electrons

The total electrical charge QQ delivered during the discharge period is given by:

Q=I⋅tQ = I \cdot t

Given:

  • Current, I=6.00 AI = 6.00\text{ A}
  • Time, t=12.0 h=12.0×3600 s=43,200 st = 12.0\text{ h} = 12.0 \times 3600\text{ s} = 43{,}200\text{ s}

Q=(6.00 A)⋅(43,200 s)=259,200 CQ = (6.00\text{ A}) \cdot (43{,}200\text{ s}) = 259{,}200\text{ C}

Using Faraday's constant (F≈96,485 C/molF \approx 96{,}485\text{ C/mol}), find the amount of electrons transferred:

ne=QF=259,200 C96,485 C/mol≈2.686 mol≈2.70 moln_e = \frac{Q}{F} = \frac{259{,}200\text{ C}}{96{,}485\text{ C/mol}} \approx 2.686\text{ mol} \approx 2.70\text{ mol}


02

Determine the Consumption of Sulfuric Acid

The overall discharge reaction is:

Pb(s)+PbOX2(s)+2HX2SOX4(aq)→2PbSOX4(s)+2HX2O(l)\ce{Pb}(s) + \ce{PbO2}(s) + 2\ce{H2SO4}(aq) \rightarrow 2\ce{PbSO4}(s) + 2\ce{H2O}(l)

The corresponding half-reactions are:

  • Anode (oxidation): Pb(s)+SOX4X2−(aq)→PbSOX4(s)+2e−\ce{Pb}(s) + \ce{SO4^2-}(aq) \rightarrow \ce{PbSO4}(s) + 2e^-
  • Cathode (reduction): PbOX2(s)+4HX+(aq)+SOX4X2−(aq)+2e−→PbSOX4(s)+2HX2O(l)\ce{PbO2}(s) + 4\ce{H+}(aq) + \ce{SO4^2-}(aq) + 2e^- \rightarrow \ce{PbSO4}(s) + 2\ce{H2O}(l)

Thus, n=2 moln = 2\text{ mol} of electrons correspond to the consumption of 2 mol2\text{ mol} of HX2SOX4\ce{H2SO4}. The stoichiometric ratio of HX2SOX4\ce{H2SO4} consumed to electrons transferred is 1:11 : 1:

Δn(HX2SOX4)=ne≈2.70 mol\Delta n(\ce{H2SO4}) = n_e \approx 2.70\text{ mol}


03

Find the Final Electrolyte Concentration

  1. Initial moles of HX2SOX4\ce{H2SO4}: ninitial=Minitial⋅V=(4.50 mol/L)⋅(1.20 L)=5.40 moln_{\text{initial}} = M_{\text{initial}} \cdot V = (4.50\text{ mol/L}) \cdot (1.20\text{ L}) = 5.40\text{ mol}
  2. Remaining moles of HX2SOX4\ce{H2SO4}: nfinal=ninitial−Δn(HX2SOX4)=5.40 mol−2.70 mol=2.70 moln_{\text{final}} = n_{\text{initial}} - \Delta n(\ce{H2SO4}) = 5.40\text{ mol} - 2.70\text{ mol} = 2.70\text{ mol}
  3. Final concentration of HX2SOX4\ce{H2SO4}: [HX2SOX4]final=nfinalV=2.70 mol1.20 L=2.25 M[\ce{H2SO4}]_{\text{final}} = \frac{n_{\text{final}}}{V} = \frac{2.70\text{ mol}}{1.20\text{ L}} = 2.25\text{ M}

The concentration of sulfuric acid drops by exactly half, from 4.50 M4.50\text{ M} to 2.25 M2.25\text{ M}.


04

Calculate the Cell Potential via the Nernst Relationship

As the cell discharges, the consumption of the aqueous reactant (HX2SOX4\ce{H2SO4}) causes a decrease in cell potential.

For the overall cell reaction with n=2n = 2 electrons transferred and a stoichiometric coefficient of 22 for HX2SOX4\ce{H2SO4}, the drop in cell potential ΔE\Delta E at 298 K298\text{ K} relative to the initial state is:

ΔE=0.0592 Vnlog⁡10([HX2SOX4]initial2[HX2SOX4]final2)\Delta E = \frac{0.0592\text{ V}}{n} \log_{10}\left( \frac{[\ce{H2SO4}]_{\text{initial}}^2}{[\ce{H2SO4}]_{\text{final}}^2} \right)

Simplifying using logarithm power rules:

ΔE=0.0592 V2⋅2log⁡10(4.50 M2.25 M)=0.0592 V⋅log⁡10(2)\Delta E = \frac{0.0592\text{ V}}{2} \cdot 2 \log_{10}\left( \frac{4.50\text{ M}}{2.25\text{ M}} \right) = 0.0592\text{ V} \cdot \log_{10}(2)

ΔE=(0.0592 V)⋅(0.3010)≈0.0178 V≈0.018 V\Delta E = (0.0592\text{ V}) \cdot (0.3010) \approx 0.0178\text{ V} \approx 0.018\text{ V}

Subtracting this drop from the cell potential gives:

Ecell=E∘−ΔE=2.050 V−0.018 V=+2.032 VE_{\text{cell}} = E^\circ - \Delta E = 2.050\text{ V} - 0.018\text{ V} = +2.032\text{ V}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets that each mole of H2SO4 consumed corresponds to one mole of electrons (2 mol H2SO4 per 2 mol e⁻) and instead divides moles of electrons by 2, underestimating the acid consumed.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Q=(6.00 A)(12.0⋅3600 s)=259200 C  ⟹  ne=25920096485=2.686 molQ = (6.00\text{ A})(12.0 \cdot 3600\text{ s}) = 259200\text{ C} \implies n_e = \frac{259200}{96485} = 2.686\text{ mol}

  2. Step 2

    nconsumed=2.6862=1.343 moln_{\text{consumed}} = \frac{2.686}{2} = 1.343\text{ mol}

    Correct

    Δn(HX2SOX4)=ne⋅2 mol HX2SOX42 mol e−=2.686 mol≈2.70 mol\Delta n(\ce{H2SO4}) = n_e \cdot \frac{2\text{ mol }\ce{H2SO4}}{2\text{ mol }e^-} = 2.686\text{ mol} \approx 2.70\text{ mol}

    In the balanced redox reaction Pb+PbOX2+2HX2SOX4→2PbSOX4+2HX2O\ce{Pb} + \ce{PbO2} + 2\ce{H2SO4} \rightarrow 2\ce{PbSO4} + 2\ce{H2O}, 2 moles of electrons correspond to the consumption of 2 moles of HX2SOX4\ce{H2SO4}. The stoichiometric ratio is 1:11:1, so 2.686 mol2.686\text{ mol} of electrons consumes 2.686 mol2.686\text{ mol} of HX2SOX4\ce{H2SO4}, not 1.343 mol1.343\text{ mol}.

  3. Step 3

    ninitial=4.50⋅1.20=5.40 mol  ⟹  nfinal=5.40−1.343=4.057 mol  ⟹  [HX2SOX4]=4.0571.20=3.381 Mn_{\text{initial}} = 4.50 \cdot 1.20 = 5.40\text{ mol} \implies n_{\text{final}} = 5.40 - 1.343 = 4.057\text{ mol} \implies [\ce{H2SO4}] = \frac{4.057}{1.20} = 3.381\text{ M}

    Correct

    nfinal=5.40 mol−2.686 mol=2.714 mol≈2.70 mol  ⟹  [HX2SOX4]final=2.70 mol1.20 L=2.25 Mn_{\text{final}} = 5.40\text{ mol} - 2.686\text{ mol} = 2.714\text{ mol} \approx 2.70\text{ mol} \implies [\ce{H2SO4}]_{\text{final}} = \frac{2.70\text{ mol}}{1.20\text{ L}} = 2.25\text{ M}

    Your subtraction and molarity calculations followed valid methods, but they inherited the incorrect moles of consumed acid from Step 2.

  4. Step 4

    [HX+]=6.762 M, [SOX4X2−]=3.381 M  ⟹  Qrxn=1(6.762)4(3.381)2=4.18⋅10−5  ⟹  Ecell=2.050−0.05922log⁡(4.18⋅10−5)=2.18 V[\ce{H+}] = 6.762\text{ M},\ [\ce{SO4^2-}] = 3.381\text{ M} \implies Q_{\text{rxn}} = \frac{1}{(6.762)^4(3.381)^2} = 4.18 \cdot 10^{-5} \implies E_{\text{cell}} = 2.050 - \frac{0.0592}{2}\log(4.18 \cdot 10^{-5}) = 2.18\text{ V}

    Correct

    ΔE=0.0592 V2log⁡10([HX2SOX4]initial2[HX2SOX4]final2)=0.0592 V⋅log⁡10(2)≈0.018 V  ⟹  Ecell=2.050 V−0.018 V=+2.032 V\Delta E = \frac{0.0592\text{ V}}{2} \log_{10}\left(\frac{[\ce{H2SO4}]_{\text{initial}}^2}{[\ce{H2SO4}]_{\text{final}}^2}\right) = 0.0592\text{ V} \cdot \log_{10}(2) \approx 0.018\text{ V} \implies E_{\text{cell}} = 2.050\text{ V} - 0.018\text{ V} = +2.032\text{ V}

    Because of the previous error, your acid concentration was inaccurate. Furthermore, discharging a galvanic cell consumes active electrolyte and must lower its cell potential below E∘E^\circ, whereas your result of 2.18 V2.18\text{ V} incorrectly showed the cell voltage increasing.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the total charge passed using Q=I⋅tQ = I \cdot t.

You accurately converted total charge into moles of electrons using Faraday's constant.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Stoichiometric electron-to-reactant ratio mismatch

You divided the moles of electrons by 2 instead of matching the 2 mol HX2SOX4:2 mol e−2\text{ mol }\ce{H2SO4} : 2\text{ mol }e^- stoichiometry of the cell reaction.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the number of electrons transferred in the redox half-reaction (n=2n = 2) with the stoichiometric factor between electrons and reactant consumed. While each individual half-reaction involves 2e−2e^-, the overall balanced equation also consumes 2HX2SOX42\ce{H2SO4}, meaning 1 mol HX2SOX41\text{ mol }\ce{H2SO4} is consumed for every 1 mol e−1\text{ mol }e^- transferred.

REASONING PATH
Your ACEpath teacher’s suggested approach
Stoichiometric Ratio Check
  • Relate moles of reactant to moles of electrons by writing both half-reactions: Δn(reactant)=ne×νreactantnerxn\Delta n(\text{reactant}) = n_e \times \frac{\nu_{\text{reactant}}}{n_e^{\text{rxn}}}.

  • Always compare the coefficient of the species of interest in the balanced reaction directly against the number of electrons nn in the half-reaction.

Physical Reality Check for Batteries
  • As a galvanic cell discharges spontaneously, reactants are depleted and cell potential must decrease (Edischarge<EchargedE_{\text{discharge}} < E_{\text{charged}}).

  • If your calculated EcellE_{\text{cell}} increases after discharging, check the sign of ΔE\Delta E and the direction of the concentration change.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Determine the molar ratio of HX2SOX4\ce{H2SO4} to electrons transferred: the balanced reaction Pb+PbOX2+2HX2SOX4→2PbSOX4+2HX2O\ce{Pb} + \ce{PbO2} + 2\ce{H2SO4} \rightarrow 2\ce{PbSO4} + 2\ce{H2O} transfers n=2 mol e−n = 2\text{ mol }e^- while consuming 2 mol HX2SOX42\text{ mol }\ce{H2SO4}. Thus, Δn(HX2SOX4)=ne=2.686 mol≈2.70 mol\Delta n(\ce{H2SO4}) = n_e = 2.686\text{ mol} \approx 2.70\text{ mol}.

  2. Calculate final moles and concentration: nfinal=5.40 mol−2.70 mol=2.70 moln_{\text{final}} = 5.40\text{ mol} - 2.70\text{ mol} = 2.70\text{ mol}, so [HX2SOX4]final=2.70 mol1.20 L=2.25 M[\ce{H2SO4}]_{\text{final}} = \frac{2.70\text{ mol}}{1.20\text{ L}} = 2.25\text{ M}.

  3. Calculate the drop in potential: ΔE=0.0592 V2⋅2log⁡10(4.50 M2.25 M)=0.0592log⁡10(2)≈0.0178 V≈0.018 V\Delta E = \frac{0.0592\text{ V}}{2} \cdot 2\log_{10}\left(\frac{4.50\text{ M}}{2.25\text{ M}}\right) = 0.0592 \log_{10}(2) \approx 0.0178\text{ V} \approx 0.018\text{ V}.

  4. Subtract the drop from the initial cell potential: Ecell=2.050 V−0.018 V=+2.032 VE_{\text{cell}} = 2.050\text{ V} - 0.018\text{ V} = +2.032\text{ V}.

Final answer

Ecell=+2.032 VE_{\text{cell}} = +2.032\text{ V}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice matching moles of electrons to reacting species by writing out the oxidation and reduction half-reactions explicitly.

  • Perform a sanity check on battery discharge calculations to confirm that cell voltage decreases as reactants are consumed.

OverviewACEpath Teacher's Diagnosis

02 The student ignores the instruction that both protons dissociate completely and expresses the reaction quotient directly in terms of undissociated H2SO4 as Q = 1 / [H2SO4]².

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Q = (6.00 A\text{ A})(43200 s\text{ s}) = 259200 C\text{ C}   ⟹  \implies n_e = 25920096485\frac{259200}{96485} = 2.686 mol\text{ mol}   ⟹  \implies Moles of \text{Moles of } HX2SOX4\ce{H2SO4}  consumed\text{ consumed} = 2.686 mol\text{ mol}

  2. Step 2

    Initial moles of \text{Initial moles of } HX2SOX4\ce{H2SO4} = 4.50 ⋅\cdot 1.20 = 5.40 mol\text{ mol}   ⟹  \implies Remaining moles of \text{Remaining moles of } HX2SOX4\ce{H2SO4} = 5.40 - 2.686 = 2.714 mol\text{ mol}   ⟹  \implies [HX2SOX4\ce{H2SO4}] = 2.7141.20\frac{2.714}{1.20} = 2.262 M\text{ M}

  3. Step 3

    Q_{rxn\text{rxn}} = 1[HX2SOX4]2\frac{1}{[\ce{H2SO4}]^2} = 1(2.262)2\frac{1}{(2.262)^2} = 0.1954   ⟹  \implies E_{cell\text{cell}} = 2.050 - (0.05922)\left(\frac{0.0592}{2}\right) ⋅\cdot \log(0.1954) = 2.050 + 0.021 = 2.071 V\text{ V}

    Correct

    Δ\Delta E = 0.0592 V2\frac{0.0592\text{ V}}{2} \log([HX2SOX4]initial2[HX2SOX4]final2)\left(\frac{[\ce{H2SO4}]_{\text{initial}}^2}{[\ce{H2SO4}]_{\text{final}}^2}\right) = 0.0592 V\text{ V} ⋅\cdot \log(2) ≈\approx 0.018 V\text{ V}   ⟹  \implies E_{cell\text{cell}} = 2.050 V\text{ V} - 0.018 V\text{ V} = +2.032 V\text{ V}_

    You computed an absolute reaction quotient against standard state (1 M1\text{ M}) rather than determining the potential change caused by the depletion of HX2SOX4\ce{H2SO4} from its initial concentration. Because [HX2SOX4]>1 M[\ce{H2SO4}] > 1\text{ M}, your Qrxn<1Q_{\text{rxn}} < 1 produced a negative logarithm, leading to a calculated voltage increase to +2.071 V+2.071\text{ V}. As a battery discharges, consuming reactant must decrease the cell potential.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used Faraday's law to determine the quantity of charge and moles of electrons passed.

You accurately identified the 1:11:1 stoichiometric equivalence between moles of electrons transferred and moles of HX2SOX4\ce{H2SO4} consumed.

You correctly found the remaining moles and final molarity of the electrolyte solution.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Nernst equation application to battery discharge

You treated the cell potential formula in a way that resulted in an addition rather than a subtraction of potential, predicting that discharging a battery makes its voltage increase.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You evaluated an absolute reaction quotient Q=1/[HX2SOX4]2Q = 1/[\ce{H2SO4}]^2 relative to a 1 M1\text{ M} standard state without referencing the initial operating potential of the battery. Since sulfuric acid is a reactant that is consumed during discharge, the cell potential must decrease. The drop in potential is governed by the ratio of initial to final reactant concentrations: ΔE=0.0592nlog⁡([HX2SOX4]initial2[HX2SOX4]final2)\Delta E = \frac{0.0592}{n} \log\left(\frac{[\ce{H2SO4}]_{\text{initial}}^2}{[\ce{H2SO4}]_{\text{final}}^2}\right).

REASONING PATH
Your ACEpath teacher’s suggested approach
Physical Reality Check for Discharging Batteries
  • During discharge, galvanic cells consume reactants and produce products, so the cell potential must always decrease relative to its charged state (Efinal<EinitialE_{\text{final}} < E_{\text{initial}}).

  • Always verify that your calculated potential after discharge is lower than the initial potential.

Tracking Potential Drop via Concentration Ratios
  • When given a reference potential for a cell at an initial concentration, the decrease in potential is ΔE=0.0592 Vnlog⁡([Reactant]initiala[Reactant]finala)\Delta E = \frac{0.0592\text{ V}}{n} \log\left(\frac{[\text{Reactant}]_{\text{initial}}^a}{[\text{Reactant}]_{\text{final}}^a}\right).

  • Express the Nernst potential change as a subtraction of the concentration ratio term from the starting cell potential.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate the concentration ratio of the reactant: [HX2SOX4]initial[HX2SOX4]final=4.50 M2.25 M=2.00\frac{[\ce{H2SO4}]_{\text{initial}}}{[\ce{H2SO4}]_{\text{final}}} = \frac{4.50\text{ M}}{2.25\text{ M}} = 2.00.

  2. Determine the voltage decrease using the stoichiometric coefficient (22) and number of electrons (n=2n = 2): ΔE=0.0592 V2log⁡10(22)=0.0592 V⋅log⁡10(2)≈0.0178 V≈0.018 V\Delta E = \frac{0.0592\text{ V}}{2} \log_{10}(2^2) = 0.0592\text{ V} \cdot \log_{10}(2) \approx 0.0178\text{ V} \approx 0.018\text{ V}.

  3. Subtract the voltage drop from the initial cell potential: Ecell=2.050 V−0.018 V=+2.032 VE_{\text{cell}} = 2.050\text{ V} - 0.018\text{ V} = +2.032\text{ V}.

Final answer

E_{cell\text{cell}} = +2.032 V\text{ V}_

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice calculating cell potential drops directly using initial-to-final concentration ratios for practical batteries.

  • Perform a physical sanity check after every battery problem: discharging must decrease voltage, while charging increases voltage.

OverviewACEpath Teacher's Diagnosis

03 The student incorrectly writes the reaction quotient with reactants in the numerator (Q = [H+]⁴ · [SO4²⁻]²) instead of the denominator, reversing the sign of the Nernst potential adjustment.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Q=(6.00 A)(43200 s)=259200 C  ⟹  ne=25920096485=2.686 molQ = (6.00\text{ A})(43200\text{ s}) = 259200\text{ C} \implies n_e = \frac{259200}{96485} = 2.686\text{ mol}

  2. Step 2

    Moles of HX2SOX4 reacted=2.686 mol  ⟹  Remaining moles=5.40−2.686=2.714 mol  ⟹  [HX2SOX4]=2.7141.20=2.262 M  ⟹  [HX+]=4.524 M, [SOX4X2−]=2.262 M\text{Moles of }\ce{H2SO4}\text{ reacted} = 2.686\text{ mol} \implies \text{Remaining moles} = 5.40 - 2.686 = 2.714\text{ mol} \implies [\ce{H2SO4}] = \frac{2.714}{1.20} = 2.262\text{ M} \implies [\ce{H+}] = 4.524\text{ M},\ [\ce{SO4^2-}] = 2.262\text{ M}

  3. Step 3

    Qrxn=[HX+]4⋅[SOX4X2−]2=(4.524)4⋅(2.262)2=2143Q_{\text{rxn}} = [\ce{H+}]^4 \cdot [\ce{SO4^2-}]^2 = (4.524)^4 \cdot (2.262)^2 = 2143

    Correct

    Qrxn=1[HX+]4[SOX4X2−]2=1(4.524)4(2.262)2≈12143≈4.67×10−4Q_{\text{rxn}} = \frac{1}{[\ce{H+}]^4 [\ce{SO4^2-}]^2} = \frac{1}{(4.524)^4 (2.262)^2} \approx \frac{1}{2143} \approx 4.67 \times 10^{-4}

    In the overall cell reaction, sulfuric acid is a reactant, while the products (PbSOX4\ce{PbSO4} and HX2O\ce{H2O}) are pure solids and liquids with unit activity (a=1a = 1). Because reaction quotients are defined as activities of productsactivities of reactants\frac{\text{activities of products}}{\text{activities of reactants}}, the aqueous ion concentrations belong in the denominator.

  4. Step 4

    Ecell=2.050−(0.05922)⋅log⁡(2143)=2.050−0.0986=1.951 VE_{\text{cell}} = 2.050 - \left(\frac{0.0592}{2}\right) \cdot \log(2143) = 2.050 - 0.0986 = 1.951\text{ V}

    Correct

    Ecell=+2.032 VE_{\text{cell}} = +2.032\text{ V}

    Because QQ was inverted in Step 3, the logarithmic term had the wrong sign, leading to an incorrect final potential.

WHAT YOU DID WELL
Compliments from Your Teacher

You calculated the total electrical charge and moles of transferred electrons accurately using Faraday's constant.

You correctly used the half-reaction stoichiometry to find that 1 mol1\text{ mol} of HX2SOX4\ce{H2SO4} is consumed per mole of electrons.

You accurately accounted for the complete dissociation of both protons when determining the final ion concentrations.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted Reaction Quotient

You set up the reaction quotient with the aqueous species in the numerator instead of the denominator.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing reactants with products when constructing the equilibrium expression or reaction quotient for a cell where all products are pure condensed phases (a=1a = 1).

REASONING PATH
Your ACEpath teacher’s suggested approach
Constructing Reaction Quotient $Q$
  • Q=∏[aqueous products]νi∏[aqueous reactants]νjQ = \frac{\prod [\text{aqueous products}]^{\nu_i}}{\prod [\text{aqueous reactants}]^{\nu_j}}, with pure solids and liquids assigned an activity of 11.

  • Check the chemical equation and identify whether the dissolved ions appear on the left (reactants) or right (products) before writing QQ.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write the reaction quotient with the reactants in the denominator: Q=1[HX+]4[SOX4X2−]2=12143=4.67×10−4Q = \frac{1}{[\ce{H+}]^4 [\ce{SO4^2-}]^2} = \frac{1}{2143} = 4.67 \times 10^{-4}.

  2. Substitute QQ into the Nernst equation: Ecell=E∘−0.0592 V2log⁡10(12143)=2.050 V−(−0.0986 V)E_{\text{cell}} = E^\circ - \frac{0.0592\text{ V}}{2} \log_{10}\left(\frac{1}{2143}\right) = 2.050\text{ V} - (-0.0986\text{ V}).

  3. Alternatively, using the initial-to-final concentration ratio relative to standard state: ΔE=0.0592 V2log⁡10((4.50)2(2.25)2)=0.0592 V⋅log⁡10(2)≈0.018 V\Delta E = \frac{0.0592\text{ V}}{2} \log_{10}\left(\frac{(4.50)^2}{(2.25)^2}\right) = 0.0592\text{ V} \cdot \log_{10}(2) \approx 0.018\text{ V}, giving Ecell=2.050 V−0.018 V=+2.032 VE_{\text{cell}} = 2.050\text{ V} - 0.018\text{ V} = +2.032\text{ V}.

Final answer

Ecell=+2.032 VE_{\text{cell}} = +2.032\text{ V}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review how to write QQ when pure solids and liquids are present, ensuring reactants always stay in the denominator.

  • Practice using Le Chatelier's principle as a sanity check: consuming reactants shifts equilibrium toward reactants, which must lower cell potential relative to higher initial reactant concentrations.

Lock it in

Similar question

01

A lead-acid cell delivers a constant current of 5.00 A5.00\text{ A} for 5.36 hours5.36\text{ hours}. Calculate the total moles of HX2SOX4\ce{H2SO4} consumed during this period (F=96,485 C/molF = 96{,}485\text{ C/mol}).

Answer

1.00 mol HX2SOX41.00\text{ mol }\ce{H2SO4}. Total charge Q=(5.00 A)(19,300 s)=96,500 CQ = (5.00\text{ A})(19{,}300\text{ s}) = 96{,}500\text{ C}. Moles of electrons ne=96,500 C96,485 C/mol≈1.00 moln_e = \frac{96{,}500\text{ C}}{96{,}485\text{ C/mol}} \approx 1.00\text{ mol}. Since 2 mol HX2SOX42\text{ mol }\ce{H2SO4} are consumed per 2 mol e−2\text{ mol }e^-, Δn(HX2SOX4)=1.00 mol\Delta n(\ce{H2SO4}) = 1.00\text{ mol}.

02

A silver-zinc battery discharges via Zn(s)+AgX2O(s)+HX2O(l)→Zn(OH)X2(s)+2Ag(s)\ce{Zn}(s) + \ce{Ag2O}(s) + \ce{H2O}(l) \rightarrow \ce{Zn(OH)2}(s) + 2\ce{Ag}(s). If the battery passes 0.400 mol0.400\text{ mol} of electrons, how many moles of AgX2O\ce{Ag2O} are consumed?

Answer

0.200 mol AgX2O0.200\text{ mol }\ce{Ag2O}. The reaction involves n=2 mol e−n = 2\text{ mol }e^- per 1 mol AgX2O1\text{ mol }\ce{Ag2O} consumed (reduction: AgX2O+HX2O+2 eX−→2 Ag+2 OHX−\ce{Ag2O + H2O + 2e- -> 2Ag + 2OH-}). Thus, Δn(AgX2O)=0.400 mol e−×1 mol AgX2O2 mol e−=0.200 mol\Delta n(\ce{Ag2O}) = 0.400\text{ mol } e^- \times \frac{1\text{ mol }\ce{Ag2O}}{2\text{ mol }e^-} = 0.200\text{ mol}.

03

A single lead-acid cell (E∘=+2.050 VE^\circ = +2.050\text{ V}) contains 0.500 L0.500\text{ L} of 5.00 M HX2SOX45.00\text{ M }\ce{H2SO4}. After discharging at 10.0 A10.0\text{ A} for 4.00 hours4.00\text{ hours}, calculate the remaining [HX2SOX4][\ce{H2SO4}] and the cell potential EcellE_{\text{cell}} at 298 K298\text{ K} using the relationship ΔE=0.0592log⁡10([HX2SOX4]0[HX2SOX4]t)\Delta E = 0.0592\log_{10}\left(\frac{[\ce{H2SO4}]_0}{[\ce{H2SO4}]_t}\right).

Answer

[HX2SOX4]=2.02 M[\ce{H2SO4}] = 2.02\text{ M} and Ecell=+2.027 VE_{\text{cell}} = +2.027\text{ V}. Charge Q=(10.0)(14,400)=1.44×105 C  ⟹  ne=1.492 molQ = (10.0)(14{,}400) = 1.44 \times 10^5\text{ C} \implies n_e = 1.492\text{ mol}. Consumed HX2SOX4=1.492 mol\ce{H2SO4} = 1.492\text{ mol}. Remaining moles =(5.00)(0.500)−1.492=1.008 mol= (5.00)(0.500) - 1.492 = 1.008\text{ mol}. Final concentration =1.0080.500=2.016 M≈2.02 M= \frac{1.008}{0.500} = 2.016\text{ M} \approx 2.02\text{ M}. Voltage drop ΔE=0.0592log⁡10(5.002.016)=0.0592(0.394)≈0.0233 V\Delta E = 0.0592 \log_{10}\left(\frac{5.00}{2.016}\right) = 0.0592(0.394) \approx 0.0233\text{ V}. Final potential Ecell=2.050−0.023=+2.027 VE_{\text{cell}} = 2.050 - 0.023 = +2.027\text{ V}.

Loading workspace…