Resources
An industrial plating rinse water sample contains cadmium ions at an environmental concentration of . A chemical treatment technician adds sodium sulfide, , to precipitate cadmium as insoluble cadmium sulfide via the reaction . Convert the initial concentration of from to (), and calculate the minimum mass in grams of pure solid () required to completely precipitate all cadmium from a batch of this rinse water.
Answer and steps
Final answer
; Minimum mass of .
Steps
Convert the concentration of to molarity ()
First, convert the mass concentration from milligrams per liter () to grams per liter ():
Next, use the molar mass of cadmium () to find the molar concentration:
Determine the total moles of in the batch
Multiply the molar concentration by the total solution volume ():
(Alternative check: Total mass of . Then .)
Relate moles of to using stoichiometry
Sodium sulfide dissolves completely in water according to:
Each mole of supplies of sulfide ions ().
From the precipitation reaction:
The stoichiometric ratio between and is . Therefore, the required moles of solid equal the moles of present:
Common Pitfall: Do not confuse the ratio of to in the formula unit with the ratio of to . Every of yields exactly of reactive precipitant.
Calculate the minimum mass of pure
Using the molar mass of sodium sulfide ():
Typical errors
01 The student forgets to convert milligrams to grams, treating 450.0 mg/L directly as 450.0 g/L.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You divided by the molar mass without converting milligrams to grams first. Since molar mass is expressed in , the concentration must be converted to () before dividing.
- Step 2Correct
Your formula is completely correct, but the calculated molar amount reflects the unconverted concentration from Step 1.
- Step 3Correct
You correctly applied the stoichiometric ratio between and and multiplied by the molar mass, but the final mass carries forward the earlier factor-of- error.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly multiplied molarity by volume to determine total moles.
You correctly identified the stoichiometric equivalence between and .
You correctly multiplied moles of precipitant by its molar mass to calculate the required mass.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou substituted directly as if it were .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisOverlooking prefix units when calculating molar quantities. Molar mass has units of , so mass concentrations must always be in before dividing by molar mass.
REASONING PATH
Your ACEpath teacher’s suggested approach- Unit Alignment Check
Molar mass is given in , requiring mass to be in grams ().
Whenever a concentration is given in , divide by to convert to before computing moles.
CORRECTED PATH
ACEpath Teacher's DemonstrationConvert mass concentration to : .
Calculate molarity: .
Determine moles in : .
Calculate mass of : .
; Minimum mass of
02 The student misinterprets the 2:1 stoichiometric subscript in Na₂S as requiring 2 moles of Na₂S per mole of Cd²⁺.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
You doubled the moles of to get of . However, the precipitation reaction is , which requires a ratio of to . Since each formula unit of dissociates into and , of provides exactly of . Therefore, you only need of .
- Step 4Correct
You correctly multiplied your calculated moles by the molar mass of , but your final mass is doubled due to the stoichiometric error in Step 3.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly converted the concentration from milligrams per liter to molarity using the molar mass of cadmium.
You correctly calculated the total moles of cadmium ions present in the solution.
You applied the correct molar mass relationship to convert moles of compound into grams.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakenone
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou interpreted the subscript 2 in as meaning two moles of are needed per mole of or , rather than recognizing that the subscript belongs to sodium () while sulfide () has an implicit subscript of 1.
REASONING PATH
Your ACEpath teacher’s suggested approach- Dissociation Stoichiometry
For a soluble ionic compound , of produces of and of .
Always write out the complete dissolution equation: . Identify which ion is actively participating in the precipitation reaction.
- Net Ionic vs. Formula Unit Ratio
Relate the active precipitating ion back to the parent compound using its specific stoichiometric coefficient in the dissolution equation.
Since , set the moles of the reagent equal to the moles of sulfide needed: .
CORRECTED PATH
ACEpath Teacher's DemonstrationDetermine the stoichiometric relationship from dissolution: , which gives a ratio between and .
Relate to cadmium precipitation: , meaning .
Calculate the minimum required mass: .
; Minimum mass of
03 The student multiplies by the molar mass instead of dividing when converting concentration to molarity.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
To convert mass concentration () to molarity (), you must divide by the molar mass (), because . Multiplying gave units of instead of molarity.
- Step 2Correct
You correctly multiplied the concentration by the volume (), but the result is numerically off due to the concentration error from Step 1.
- Step 3Correct
You correctly recognized the stoichiometric equivalence between and , carried forward from your previous mole calculation.
- Step 4Correct
You correctly used the formula , but your final mass is too large because it relies on the earlier inflated mole quantity.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly converted the mass concentration from to .
You used the correct relationship between amount of substance, concentration, and solution volume ().
You correctly deduced that of provides of , reacting with in a mole ratio.
You correctly applied the relationship between mass, moles, and molar mass () in the final step.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou multiplied the mass concentration by molar mass instead of dividing by it. Remember that molar mass has units of ; dividing by cancels grams and yields .
REASONING PATH
Your ACEpath teacher’s suggested approach- Unit cancellation check
Always write out explicit units: . If units do not simplify to , invert your factor.
CORRECTED PATH
ACEpath Teacher's DemonstrationDivide the mass concentration by the molar mass of cadmium: .
Find total moles of cadmium in : .
Relate to sodium sulfide via a stoichiometric ratio: .
Calculate required mass of : .
; Minimum mass of .
Lock it in
How do you convert a mass concentration in into molarity () using molar mass in ?
Divide by to get , then divide by : .
Similar question
A solution contains of (). Convert this concentration to molarity (), and find the moles of in a container.
Answer
; total moles . Key step: , so ; .
Wastewater contains of copper ions, (). What minimum mass of solid sodium hydroxide, (), is needed to precipitate all copper as from a tank?
Answer
. Key steps: ; . Stoichiometry: , so . Mass: .
An electroplating effluent volume of contains of (). A technician precipitates aluminum by adding solid sodium carbonate: . Calculate the minimum mass in grams of pure solid () required.
Answer
. Key steps: ; . Total . Stoichiometric ratio: , so . Mass: .