Resources
A continuous Haber-Bosch ammonia synthesis loop operates at and via , with standard reaction enthalpy . Due to thermodynamic limitations, the single-pass conversion of the stoichiometric feed gas is only . To conserve material, unreacted gas is cooled to condense and recycled back to the reactor. If an industrial plant achieves an overall process yield of based on fresh stoichiometric feed and isolates of liquid per day (), determine: (a) the mass of fresh (in metric tons) that must be introduced daily, and (b) the theoretical thermal energy released (in gigajoules, ) solely by the chemical synthesis of this isolated quantity of ammonia.
Answer and steps
Final answer
(a) ; (b) .
Steps
Part (a): Mass of Fresh Required Daily
- Calculate the daily molar amount of isolated ammonia (): Using the molar mass of ammonia, (or to three significant figures):
-
Relate isolated product to the theoretical requirement of : From the balanced equation: Stoichiometrically, produces . The theoretical amount of needed to form this quantity of product is:
The theoretical mass of () is:
- Account for the overall process yield: Pitfall to avoid: The low single-pass conversion () dictates the internal recycle flow rate, not the overall raw material consumption. Because unreacted gases are recycled, raw material requirements depend solely on the overall process yield ():
Part (b): Theoretical Thermal Energy Released
- Determine the heat released per mole of produced: The standard reaction enthalpy is for the reaction as written, which generates :
- Compute total heat released by the isolated ammonia: Using the actual moles of produced:
- Convert to gigajoules (): Since :
Typical errors
01 The student misuses the 15.0% single-pass conversion instead of the 96.0% overall yield to determine fresh nitrogen feed, drastically overestimating the required fresh N2.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You divided by the single-pass conversion () rather than the overall process yield (). Because unreacted gas is recycled back to the reactor loop, fresh feed is only consumed to make up for unrecovered material determined by the overall yield.
- Step 3Correct
Your molar mass multiplication and unit conversion to metric tons were carried out correctly, but the numerical answer is inflated due to the incorrect feed moles from Step 2.
- Step 4
WHAT YOU DID WELL
Compliments from Your TeacherYou calculated the molar quantities of ammonia and stoichiometric nitrogen accurately.
You handled the unit conversion between grams and metric tons cleanly.
You related the reaction enthalpy to individual moles of ammonia and computed the thermal energy released in gigajoules without error.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou conflated single-pass conversion with overall process yield. In a recycle loop, single-pass conversion governs the internal flow circulating through the reactor, whereas overall process yield determines the net consumption of fresh feed.
REASONING PATH
Your ACEpath teacher’s suggested approach- Define the Control Boundary
For calculating fresh feed inputs, draw a global control volume around the entire plant (including the recycle loop), not just around the reactor unit.
Divide theoretical stoichiometric requirement by overall process yield, not single-pass conversion.
CORRECTED PATH
ACEpath Teacher's Demonstration(a) ; (b)
02 The student treats the reaction enthalpy as -92.2 kJ per mole of NH3 instead of per mole of reaction (2 moles of NH3), doubling the calculated thermal energy.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
The standard reaction enthalpy is given for the balanced equation as written, which produces . Therefore, the energy released per mole of ammonia is .
- Step 4Correct
Your arithmetic was carried out correctly based on your previous figure, but the numerical result is doubled due to the error in Step 3.
- Step 5Correct
One gigajoule equals . Dividing by yields an order of magnitude of , not .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the daily molar quantity of ammonia produced from its mass.
You used the stoichiometric ratio from the balanced chemical equation to relate ammonia to molecular nitrogen.
You correctly applied the overall process yield of rather than being distracted by the single-pass conversion.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou divided by instead of when converting kilojoules to gigajoules.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou interpreted as the enthalpy change per mole of product rather than per stoichiometric mole of the reaction as written, omitting the stoichiometric coefficient of for .
REASONING PATH
Your ACEpath teacher’s suggested approach- Enthalpy per Mole of Substance
For a reaction , the heat change per mole of product is .
Always divide by the coefficient of the substance of interest before multiplying by moles of that substance.
- SI Prefix Scaling for Joules
.
Divide kilojoules by (not ) to obtain gigajoules.
CORRECTED PATH
ACEpath Teacher's DemonstrationDetermine the heat released per mole of : .
Calculate the total heat released: .
Convert from to : .
(a) ; (b)
03 The student multiplies by the overall process yield of 96.0% rather than dividing by it to find the required fresh feed input.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
Because the process has a yield, the plant must feed more raw material than theoretically required, so you need to divide by rather than multiply.
- Step 4Correct
Your mass calculation follows logically from your previous molar quantity, but it carries forward the yield error from step 3.
- Step 5
- Step 6Correct
Since , dividing by yields rather than .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly converted the mass of ammonia into moles.
You accurately identified the stoichiometric ratio between and .
You correctly recognized that reaction enthalpy is given per mole of reaction, which forms of .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeIn step 6, you divided by instead of when converting kilojoules to gigajoules.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated overall yield as a discount factor on the input rather than realizing that an imperfect yield requires a larger input to achieve the desired output amount ().
REASONING PATH
Your ACEpath teacher’s suggested approach- Input vs. Output with Yield
Always verify whether the calculated input is larger than the stoichiometric requirement when fractional yield is below .
- SI Energy Prefix Conversion
Check that converting from kilo- () to giga- () shifts the exponent by .
CORRECTED PATH
ACEpath Teacher's Demonstration(a) ; (b)
Lock it in
In a chemical process with a recycle loop, what is the fundamental difference between single-pass conversion and overall process yield?
Single-pass conversion measures reactant converted in one transit through the reactor. Overall yield measures total product isolated relative to fresh feed across the entire system boundary.
Similar question
A chemical synthesis reactor operates with a single-pass conversion of , but an unreacted gas recycle loop brings the overall process yield to . To produce of product (stoichiometric ratio with reactant A), what molar amount of fresh reactant A must be introduced?
Answer
. Single-pass conversion only impacts internal recycle circulation, not net feed input.
In a continuous loop, of total mixed feed enters a catalytic reactor where is converted to product per pass. The separator recovers all product and recycles all unreacted reactant without loss (overall yield ). Determine: (a) the production rate of product, and (b) the required fresh feed rate at steady state.
Answer
(a) Product formed per pass = . (b) At steady state with overall yield, fresh feed exactly equals product output: .
Methanol is synthesized via . The reactor single-pass conversion of is . Because of a purge stream taken from the recycle loop to prevent inert gas accumulation, the overall plant yield based on is . Calculate the mass (in ) of fresh () needed to produce of pure ().
Answer
. Theoretical . Fresh . Mass of fresh .