Resources
A municipal environmental compliance officer investigates an industrial effluent stream discharged into a local river. A grab sample of the wastewater has a measured Chemical Oxygen Demand (COD) of . Spectroscopic screening confirms that the primary organic contaminant is dissolved ethylene glycol (, ), which undergoes complete chemical oxidation via: . Assuming ethylene glycol is the sole contributor to the measured Chemical Oxygen Demand, reverse-engineer: (a) the original concentration of dissolved ethylene glycol in the wastewater stream in units of , and (b) the molarity () of ethylene glycol in the effluent.
Answer and steps
Final answer
(a) ; (b)
Steps
Calculate the Mass Ratio of Ethylene Glycol to Oxygen
Understanding Chemical Oxygen Demand (COD)
Chemical Oxygen Demand (COD) measures the amount of oxygen required to chemically oxidize organic compounds in water into carbon dioxide and water. Here, dissolved ethylene glycol () is the sole contributor to the COD measurement of . The balanced oxidation reaction is: From the stoichiometry:
- of reacts with of .
- Molar mass of .
- Molar mass of .
Determine the mass of oxygen required to completely oxidize of ethylene glycol:
Thus, of consumes of . The mass conversion factor is:
Determine the Concentration in
Multiply the given COD by the stoichiometric mass ratio:
Common Pitfall: Forgetting to account for the stoichiometric factor of for is a frequent error. Always write out the stoichiometric conversion from moles to grams rather than comparing molar masses .
Determine the Molarity ()
To find molarity, convert the concentration from to :
Alternatively, calculate molarity directly from the moles of consumed:
- Moles of per liter:
- Moles of ethylene glycol per liter:
Typical errors
01 The student uses the atomic mass of oxygen (16.00 g/mol) instead of molecular oxygen (32.00 g/mol) when converting COD from mg O2 to moles, leading to an ethylene glycol concentration and molarity that are doubled.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
Chemical Oxygen Demand is expressed in terms of molecular oxygen (), which has a molar mass of , rather than atomic oxygen (, ).
- Step 3Correct
Your stoichiometric division by correctly reflects the balanced reaction ratio, but the result is doubled due to the earlier oxygen molar mass error.
- Step 4Correct
You correctly multiplied by the molar mass of ethylene glycol to find mass concentration, but the value is twice the true value due to the initial error.
- Step 5Correct
Your final molarity is directly carried from step 3 and is exactly twice the correct molarity.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly converted COD units from milligrams per liter to grams per liter.
You correctly used the stoichiometric mole ratio between ethylene glycol and oxygen from the balanced equation.
You correctly converted between molarity and mass concentration using the molar mass of ethylene glycol.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou divided by (atomic oxygen) instead of (molecular oxygen, ).
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing atomic oxygen () with diatomic molecular oxygen () when interpreting Chemical Oxygen Demand (COD). COD is always quantified in equivalents of molecular oxygen gas, .
REASONING PATH
Your ACEpath teacher’s suggested approach- COD Species Identity
Chemical Oxygen Demand is defined in terms of molecules, so .
Always check the chemical formula in the unit label: specifies diatomic , requiring division by to find moles.
CORRECTED PATH
ACEpath Teacher's Demonstration(a) ; (b)
02 The student inverts the stoichiometric ratio, multiplying the moles of O2 by 2.5 instead of dividing by 2.5, resulting in an overestimation of the ethylene glycol content.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
According to the balanced equation , of ethylene glycol requires of . Therefore, you must divide the moles of by , rather than multiplying.
- Step 3Correct
Your mass conversion method was mathematically correct, but the numerical result was affected by the inverted mole ratio in Step 2.
- Step 4Correct
Your identification of molar concentration as the molarity was conceptually sound, but the numerical value inherited the error from Step 2.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly converted the measured COD from to and determined the molar concentration of dissolved consumed.
You used the correct molar mass () to convert molar concentration into mass concentration.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou inverted the mole ratio conversion factor, multiplying by the stoichiometric coefficient of () instead of setting up dimensional analysis with .
REASONING PATH
Your ACEpath teacher’s suggested approach- Dimensional Analysis with Mole Ratios
Always write the chemical species and units explicitly in your conversion factor (e.g., ) to verify that the known unit cancels out.
CORRECTED PATH
ACEpath Teacher's Demonstration(a) ; (b)
03 The student ignores the 2.5 stoichiometric coefficient of O2, incorrectly assuming a 1:1 molar ratio between O2 consumed and ethylene glycol.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
The balanced chemical equation requires per , so you need to divide the moles of by rather than assuming an equimolar ratio.
- Step 3Correct
Your conversion method from molarity to is mathematically sound, but the value is scaled up by a factor of due to the molar ratio error in Step 2.
- Step 4Correct
This molarity directly repeats the uncorrected value from Step 2.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly expressed the COD value in grams per liter and divided by the molar mass of diatomic oxygen ().
You knew how to convert molar concentration back into mass concentration () using the molar mass of the compound.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou explicitly assumed a stoichiometric ratio between oxygen and the organic substrate, overlooking the oxidation reaction's stoichiometric coefficient of () for .
REASONING PATH
Your ACEpath teacher’s suggested approach- Stoichiometric Factor Check
Chemical Oxygen Demand measures consumed, so , where is the stoichiometric coefficient of in the complete combustion reaction.
Always balance the complete oxidation reaction or read the coefficient of directly from the prompt before relating moles of oxygen to moles of organic pollutant.
CORRECTED PATH
ACEpath Teacher's DemonstrationDivide the moles of consumed per liter by the stoichiometric coefficient of oxygen (): .
Multiply this molarity by the molar mass of ethylene glycol () to find the mass concentration: .
Convert grams per liter to milligrams per liter: .
(a) ; (b)
Lock it in
What chemical species and molar mass does the unit in Chemical Oxygen Demand (COD) refer to?
It refers to molecular oxygen () with a molar mass of , not atomic oxygen ().
Similar question
A wastewater effluent contains ethanol (, ) as its sole organic contaminant, oxidizing via . If the measured COD is , calculate the molarity () of ethanol in the effluent.
Answer
. Key steps: (1) Moles of ; (2) Stoichiometric ratio is ; (3) .
A chemical plant discharges wastewater containing acetic acid (, ), which oxidizes via . If the COD is determined to be , determine the mass concentration of acetic acid in .
Answer
. Key steps: (1) Moles of ; (2) Moles of acetic acid per liter ; (3) Mass concentration .
An environmental engineer determines that an industrial waste stream contains of glucose (, ). Write the complete combustion reaction for glucose and calculate the theoretical Chemical Oxygen Demand (ThOD) of this stream in .
Answer
. Key steps: (1) Balanced reaction: ; (2) Glucose concentration ; (3) required ; (4) .