Resources
An environmental laboratory monitors calcium contamination in industrial wastewater. Standard spectroscopic literature reports calcium's prominent atomic emission resonance line at a wavenumber of . The lab technician must configure an optical grating detector that reads in units of nanometers () and millielectronvolts (). (a) Convert the wavenumber to wavelength in nanometers (). (b) Calculate the energy of this transition in electron-volts () and millielectronvolts (), given , , and . (c) Describe the characteristic flame color produced by calcium salts and contrast it with strontium ( to red).
Answer and steps
Final answer
(a) ; (b) ; (c) Calcium produces a characteristic brick-red (orange-red) flame with strong bands in the orange-red and a distinct violet line (), whereas strontium produces an intense, deep crimson-scarlet red devoid of orange hue.
Steps
Part (a): Calculating the Wavelength ()
Wavenumber () is defined as the reciprocal of wavelength:
- Substitute the given wavenumber:
- Convert centimeters to nanometers, knowing that :
Part (b): Calculating the Energy () in and
The photon energy relates to wavenumber via Planck's equation:
- Express the speed of light in to match the units of :
- Calculate energy in joules ():
- Convert joules to electron-volts ():
- Convert electron-volts to millielectronvolts ():
Pitfall to avoid: When applying , ensure the speed of light is expressed in if is in , or convert to before multiplying by in .
Part (c): Flame Color of Calcium vs. Strontium
- Calcium (): In a flame test, calcium salts emit a characteristic brick-red (orange-red) flame. While the ground-state atomic resonance transition lies at in the violet region, flame emissions from molecular hydroxide species (such as ) produce strong continuous emission bands in the orange-red spectrum, giving the macroscopic flame its distinct brick-red hue.
- Strontium (): In contrast, strontium salts produce an intense, deep crimson or scarlet red flame. Strontium's dominant emissions appear at longer red wavelengths ( to ) without the warmer orange tint seen in calcium.
Typical errors
01 The student uses the conversion factor 1 cm = 10⁻⁹ nm (confusing meters and centimeters or inverting the power of 10), resulting in an incorrect wavelength of 4.228 × 10⁴ nm.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You equated to , which is the conversion factor for meters (). Because , the correct conversion factor is , yielding .
- Step 3
- Step 4
Calcium produces an orange-red (brick-red) flame, while strontium produces a crimson (deep red) flame.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly related wavelength to wavenumber using .
You successfully converted wavenumber to SI base units to calculate photon energy in joules via .
You accurately converted energy from joules to electron-volts and millielectronvolts.
You clearly distinguished the brick-red flame of calcium from the crimson flame of strontium.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou substituted the meter-to-nanometer prefix power () when converting from centimeters.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing base SI units with centimeter-scale prefixes during multi-step unit conversion.
REASONING PATH
Your ACEpath teacher’s suggested approach- Centimeter to Nanometer Conversion
, which implies .
Always convert through the base unit (meters) if unsure: .
CORRECTED PATH
ACEpath Teacher's DemonstrationSet up the conversion from centimeters to nanometers using the base unit meter: and , so .
Multiply the calculated wavelength in centimeters by : .
(a) ; (b) ; (c) Calcium produces a brick-red (orange-red) flame, whereas strontium produces a crimson (deep red) flame.
02 The student omits converting wavenumber from cm⁻¹ to m⁻¹ when evaluating E = hcν̃, underestimating the energy by two orders of magnitude.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
The speed of light was entered in meters per second (), while was entered in . To keep units consistent, either express in centimeters per second () or convert to reciprocal meters (). This mismatched length unit made your result times too small.
- Step 3Correct
Your conversion factors from joules to electron-volts and electron-volts to millielectronvolts were applied correctly, but the numerical value was shifted by the error in the previous step.
- Step 4
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly used the reciprocal relationship between wavelength and wavenumber.
You converted centimeters to nanometers with the proper scaling factor.
You used the correct conversion ratios between joules, electron-volts, and millielectronvolts.
You correctly distinguished calcium's brick-red flame from strontium's crimson flame.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou substituted in alongside in without matching the metric base units.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisOverlooking the unit dimensional mismatch between SI meters in () and CGS centimeters in wavenumber () when computing .
REASONING PATH
Your ACEpath teacher’s suggested approach- Unit Alignment Check
In , the spatial unit in must match the spatial unit in .
Always write out unit labels: or .
CORRECTED PATH
ACEpath Teacher's DemonstrationConvert to : .
Calculate in joules using SI units: .
Convert energy to electron-volts: .
Convert energy to millielectronvolts: .
(a) ; (b) ; (c) Calcium produces a brick-red flame, whereas strontium produces a crimson-red flame.
03 The student confuses the metric prefix milli (10⁻³) with micro (10⁻⁶), dividing by 1,000 or using 10⁻³ meV per eV instead of multiplying by 1,000.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
Because the prefix milli denotes (), there are in . You divided by instead of multiplying, which yielded a value that was six orders of magnitude too small.
- Step 4
WHAT YOU DID WELL
Compliments from Your TeacherYou related wavelength to wavenumber using the reciprocal relationship.
You carried out the dimensional analysis between centimeters and nanometers without error.
You correctly matched the spatial units when computing photon energy with Planck's constant.
You clearly distinguished the brick-red flame of calcium from the crimson flame of strontium.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou divided by when converting from a base unit () to a milli-unit (), reversing the unit scale factor.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou associated the prefix multiplier directly with dividing the numerical value, confusing the relationship with the ratio needed to convert from into . A smaller unit must yield a larger numerical measure.
REASONING PATH
Your ACEpath teacher’s suggested approach- Unit Magnitude Sanity Check
When converting from a larger unit to a smaller subdivided unit, the numerical value must increase.
Check whether your target unit is smaller than your source unit: since a millielectronvolt is smaller than an electron-volt, the number of must be larger than the number of .
- Fractional Unit Factor Setup
Multiply by a conversion factor equal to : .
Always write out the explicit fraction with canceling units: .
CORRECTED PATH
ACEpath Teacher's DemonstrationIdentify the relationship: , which means .
Multiply the value in by the conversion ratio: .
Calculate the result: .
(a) ; (b) (or ); (c) Calcium produces a brick-red flame, whereas strontium produces a crimson-red flame.
Lock it in
How many nanometers () are in one centimeter ()?
. Memory cue: and , so .
Similar question
A potassium emission line occurs at a wavenumber of . Convert this wavenumber to wavelength in nanometers () and state the characteristic flame color of potassium.
Answer
; lilac (pale violet) flame. Key steps:
- .
- .
An infrared absorption peak of carbon dioxide occurs at . (a) Calculate the wavelength in micrometers () and in nanometers (). (b) Calculate the energy of one photon of this transition in millielectronvolts (), given .
Answer
(a) ; (b) . Key steps:
- .
- .
- .
A diode laser emits at . (a) Express this wavelength in centimeters (). (b) Determine the wavenumber in . (c) If a student accidentally divides by instead of using centimeters, what error factor does this introduce into the wavenumber?
Answer
(a) ; (b) ; (c) An overestimation by a factor of (). Key steps:
- .
- .
- Using gives , which is times larger than the numerical value in .