Resources
An analytical chemist measures the mass of an anhydrous sodium carbonate precipitate three consecutive times on an analytical balance, obtaining values of , , and . Calculate the mean mass and the sample standard deviation () of these measurements, reporting both values with the correct number of significant figures and decimal places according to standard experimental chemistry conventions.
Answer and steps
Final answer
, (or )
Steps
Calculate the Mean Mass ()
The arithmetic mean of measurements is defined as:
Substitute the three measured masses into the formula:
Significant Figures and Decimal Places Rule:
- The numerator is an addition of values, each having three decimal places, resulting in (three decimal places).
- The denominator () is an exact counting integer with infinite significant figures.
- Therefore, the mean retains three decimal places: .
Calculate the Sample Standard Deviation ()
The sample standard deviation represents the precision or dispersion of repeated measurements around the mean and is calculated using:
-
Calculate the deviation of each measurement from the mean ():
-
Square each deviation:
- Sum the squared deviations:
- Divide by the degrees of freedom ():
- Take the square root:
Match Uncertainty and Experimental Value Precision
- In analytical chemistry, experimental uncertainty (such as standard deviation) is typically reported to one significant figure unless the leading digit is or (where two significant figures are sometimes kept). Here, has one significant figure.
- The reported mean must share the same last significant decimal position as the uncertainty (the thousandths place, ).
Thus, the results are: or reported jointly as:
Typical errors
01 The student calculates population standard deviation by dividing by N instead of the sample degrees of freedom N - 1.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
You divided by the total number of measurements (which gives the population standard deviation ) rather than the sample degrees of freedom .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the mean mass with proper decimal precision.
You found each individual deviation accurately.
You calculated the sum of squared deviations without any arithmetic errors.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou divided by the total sample size rather than the degrees of freedom in the denominator of the standard deviation formula.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing sample standard deviation () with population standard deviation (). When analyzing a small set of experimental laboratory measurements, one degree of freedom is consumed to estimate the sample mean , requiring division by (Bessel's correction) to avoid underestimating experimental dispersion.
REASONING PATH
Your ACEpath teacher’s suggested approach- Sample vs. Population Standard Deviation
For a finite set of experimental sample trials, use . Division by applies only when the true population mean is known or when measuring an entire population.
Always verify whether you are calculating a sample statistic () or a population parameter ().
- Degrees of Freedom Check
For repeat measurements, the sample variance has degrees of freedom.
Before taking the square root, write out explicitly in the denominator.
CORRECTED PATH
ACEpath Teacher's DemonstrationIdentify degrees of freedom: for , degrees of freedom is .
Compute sample variance: .
Take square root to find sample standard deviation: .
(or )
02 The student forgets to take the square root of the variance when computing the standard deviation.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
You divided by the degrees of freedom (), which gives the sample variance . To find the standard deviation , you must take the square root of the variance.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly computed the arithmetic mean with the appropriate decimal places and units.
You accurately calculated each deviation from the mean and summed their squares.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou stopped after calculating the sample variance () and labeled it as the standard deviation (), missing the required square root step to return to the original measurement units.
REASONING PATH
Your ACEpath teacher’s suggested approach- Variance vs. Standard Deviation Formula
(or )
Always verify whether your formula has a radical symbol over the divided sum of squares.
- Dimensional Analysis / Unit Consistency
The standard deviation must have the same physical units as the original measurements (), whereas variance has squared units ().
Check your units at each stage: yields , signaling that taking is still required.
CORRECTED PATH
ACEpath Teacher's DemonstrationCompute the sample variance: .
Take the square root of the variance to determine the sample standard deviation: .
Match precision: report the standard deviation to one significant figure () and express the final result alongside the mean as .
(or )
03 The student misapplies significant figure rules by matching the 5 significant figures of the raw mass data rather than matching the decimal place precision of the deviations.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
You performed the arithmetic correctly, but you added trailing zeros to give five significant figures. In experimental chemistry, standard deviation () represents measurement uncertainty and is conventionally reported to one significant figure (unless the leading digit is or ), matching the decimal place of the balance precision ().
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the sample mean mass with appropriate units and decimal places.
You determined the individual residuals and the sum of squared deviations without arithmetic errors.
You used the correct degrees of freedom () in the sample standard deviation formula.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou appended four trailing zeros to the standard deviation (), confusing the five significant figures of the raw mass data with the precision of experimental uncertainty.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConflating raw measurement significant figures with uncertainty reporting conventions. Experimental uncertainty () is governed by the precision of the deviations and is standardly rounded to one significant figure (e.g., ), which then dictates the decimal place to which the mean is reported.
REASONING PATH
Your ACEpath teacher’s suggested approach- Uncertainty Significant Figures
In analytical chemistry, report experimental uncertainty () to significant figure (or if the leading digit is or ).
Round to one significant figure without appending trailing zeros.
- Coordinate Mean and Uncertainty Precision
The final mean and its standard deviation must terminate at the same decimal place.
Check that both the mean () and () end at the thousandths place ().
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate the sample variance using degrees of freedom: .
Take the square root to find standard deviation: .
Apply standard uncertainty conventions: round to one significant figure () with no trailing zeros.
, (or )
Lock it in
What is the difference between the formula for sample standard deviation () and population standard deviation ()?
Sample standard deviation divides by degrees of freedom , whereas population standard deviation divides by total population size .
Similar question
A student titrates three aliquots of acid, recording volumes of , , and . Calculate the mean volume and the sample standard deviation (), reporting both with appropriate significant figures.
Answer
, (reported as ). The mean is . Deviations are , , and . The sum of squared deviations is . Dividing by gives , so .
Four replicate density determinations of an unknown liquid yield values of , , , and . Determine the mean density and the sample standard deviation ().
Answer
, (reported as ). The mean is . Deviations are , , , and . Sum of squared deviations is . Dividing by yields , so .
A student measures five values: , , , , and . If the student mistakenly uses instead of , by what multiplicative factor will the calculated standard deviation underestimate the correct sample standard deviation?
Answer
The student's value underestimates the correct sample standard deviation by a factor of (about lower than the true sample standard deviation). Since and , the ratio is .