Resources
A biomedical freezer stores a biological preservative solution whose primary component is pure liquid methanol at its normal freezing point of . A thermal disturbance introduces heat into a sample of the solid methanol (density at this temperature). The molar enthalpy of fusion of methanol is , and its molar mass is . Calculate the heat required, in kilojoules (), to melt this volume of methanol completely.
Answer and steps
Final answer
Steps
Calculate the mass of the methanol sample
To find the total heat required to melt the solid methanol at its melting point, we determine the amount of substance (in moles) undergoing the phase change and multiply it by the molar enthalpy of fusion.
Using the given volume and density at the freezing point:
Convert mass to moles
Using the molar mass of methanol ():
Calculate the heat required for fusion
Because the methanol is already at its melting point (), no temperature change occurs during the phase transition (). The heat required depends solely on the phase change:
Rounding to three significant figures gives:
Common Pitfall: Do not use the specific heat formula . During a phase transition (melting or freezing), temperature remains constant while energy is absorbed to overcome intermolecular forces. Additionally, always check the units of : since it is given per mole (), mass must be converted into moles before multiplying.
Typical errors
01 A student might assume the density is 1.00 g/mL (or confuse volume with mass) and directly use the numerical volume in milliliters as the mass in grams.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You treated the volume of as though it were directly , but methanol has a density of , so the mass must be calculated as .
- Step 2Correct
Your formula and arithmetic were correct, but the result was affected by the initial mass error.
- Step 3Correct
Your formula was set up correctly, but the final energy reflects the earlier mass value.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified and applied the relationship between mass, molar mass, and moles ().
You chose the correct thermochemical formula for a phase change at constant temperature ().
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated milliliters of liquid/solid methanol as interchangeable with grams, overlooking that is an approximation specific to pure liquid water at room temperature, not other substances with different densities.
REASONING PATH
Your ACEpath teacher’s suggested approach- Check Given Units Before Starting
Volume () and mass () are distinct physical quantities related by density: .
Whenever a volume is provided alongside a density, multiply them to determine the mass in grams before converting to moles.
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate mass from volume and density: .
Convert mass to moles: .
Calculate the required heat of fusion: .
02 A student might multiply the mass by the molar mass instead of dividing by it when attempting to find the number of moles.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
To convert mass into moles, you must divide mass by molar mass (). Multiplying grams by grams per mole yields units of rather than moles.
- Step 3Correct
You correctly chose the isothermal phase-change relationship , but your calculation used the incorrect mole value carried over from Step 2.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the mass of the sample using volume and density.
You recognized that melting at the freezing point requires the latent heat relation rather than a temperature-dependent formula.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou accidentally multiplied grams by molar mass instead of dividing by molar mass.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisInverting the dimensional conversion factor between mass and moles, failing to cancel grams in the denominator.
REASONING PATH
Your ACEpath teacher’s suggested approach- Unit Cancellation Check
Write out the conversion factor explicitly with fractional units to confirm that grams cancel and leave moles.
- Reasonableness Check
For a substance with , approximately must equal between and .
Perform a quick mental estimate before proceeding to ensure the mole quantity is physically reasonable.
CORRECTED PATH
ACEpath Teacher's DemonstrationRounding to three significant figures gives .
03 A student might directly multiply the mass in grams by the molar enthalpy of fusion without first converting grams to moles.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
The molar enthalpy of fusion is given in , not . Multiplying grams by yields mismatched units (). You need to divide mass by the molar mass () to find moles before multiplying by .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly used the density and volume to determine the mass of the solid methanol sample.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated the molar enthalpy of fusion as a specific enthalpy per gram rather than checking the denominator unit (per mole) and converting grams to moles.
REASONING PATH
Your ACEpath teacher’s suggested approach- Unit Dimensional Check
requires in moles when is in .
Always look at the denominator of the enthalpy value; if it says , convert grams to moles using molar mass before multiplying.
CORRECTED PATH
ACEpath Teacher's DemonstrationConvert mass to moles:
Multiply moles by molar enthalpy of fusion:
Round to three significant figures:
Lock it in
When can you directly set without using density?
Only for pure liquid water near (where ). For all other substances or temperatures, you must use .
Similar question
A sample of of liquid benzene (density , molar mass ) is frozen at its normal freezing point. Given that , calculate the heat released in kilojoules.
Answer
Mass: .\nMoles: .\nHeat released: .
A container holds of solid diethyl ether at its melting point (). The solid density is , molar mass is , and . Calculate the heat in required to melt the ether.
Answer
Mass: .\nMoles: .\nHeat required: .
An unknown pure hydrocarbon liquid with a density of and molar mass of requires of energy to vaporize at its normal boiling point. Calculate the molar enthalpy of vaporization () in .
Answer
Mass: .\nMoles: .\n.