Resources

In a green analytical chemistry experiment designed to eliminate chlorinated waste, an organic acid sample is analyzed via automated potentiometric micro-titration using an aqueous sodium hydroxide titrant prepared with degassed deionized water. A 0.1852 g0.1852\text{ g} sample of pure, dry potassium hydrogen phthalate (KHP, KHC8H4O4\text{KHC}_8\text{H}_4\text{O}_4, molar mass 204.22 g/mol204.22\text{ g/mol}) is dissolved in 25.00 mL25.00\text{ mL} of water and titrated to the potentiometric equivalence point, requiring 18.45 mL18.45\text{ mL} of the NaOH\text{NaOH} solution. Then, a 10.00 mL10.00\text{ mL} aliquot of an industrial dilute acetic acid waste stream (density 1.005 g/mL1.005\text{ g/mL}) requires 14.20 mL14.20\text{ mL} of this standardized NaOH\text{NaOH} solution to reach the equivalence point: CH3COOH+NaOH→CH3COONa+H2O\text{CH}_3\text{COOH} + \text{NaOH} \rightarrow \text{CH}_3\text{COONa} + \text{H}_2\text{O}. Calculate (a) the exact molarity of the standardized NaOH\text{NaOH} solution and (b) the mass percent (% w/w\text{\% w/w}) of acetic acid (molar mass 60.05 g/mol60.05\text{ g/mol}) in the waste stream to three significant figures.

Answer and steps

Final answer

(a) [NaOH]=0.04915 M[\text{NaOH}] = 0.04915\text{ M}; (b) Mass percent of CH3COOH=0.417%\text{CH}_3\text{COOH} = 0.417\%

Steps

Part (a): Determining the Concentration of the NaOH\ce{NaOH} Solution

  1. Calculate the moles of primary standard used: Potassium hydrogen phthalate (KHP\ce{KHP}, KHCX8HX4OX4\ce{KHC8H4O4}) reacts with sodium hydroxide (NaOH\ce{NaOH}) in a 1:11:1 stoichiometric ratio: KHCX8HX4OX4+NaOH→KNaCX8HX4OX4+HX2O\ce{KHC8H4O4 + NaOH -> KNaC8H4O4 + H2O}

    The amount of KHP\ce{KHP} titrated is: Moles of KHP=MassMolar Mass=0.1852 g204.22 g/mol≈9.0687×10−4 mol\text{Moles of KHP} = \frac{\text{Mass}}{\text{Molar Mass}} = \frac{0.1852\text{ g}}{204.22\text{ g/mol}} \approx 9.0687 \times 10^{-4}\text{ mol}

  2. Calculate the molarity of NaOH\ce{NaOH}: Because the stoichiometric ratio is 1:11:1, the moles of NaOH\ce{NaOH} at the equivalence point equal the moles of KHP\ce{KHP}: Moles of NaOH=9.0687×10−4 mol\text{Moles of } \ce{NaOH} = 9.0687 \times 10^{-4}\text{ mol}

    Convert the titrant volume from milliliters to liters: V=18.45 mL=0.01845 LV = 18.45\text{ mL} = 0.01845\text{ L}

    The molarity ([NaOH][\ce{NaOH}]) is: [NaOH]=9.0687×10−4 mol0.01845 L=0.0491526 M≈0.04915 M[\ce{NaOH}] = \frac{9.0687 \times 10^{-4}\text{ mol}}{0.01845\text{ L}} = 0.0491526\text{ M} \approx 0.04915\text{ M}


Part (b): Determining the Mass Percent of Acetic Acid in the Waste Stream

  1. Calculate the moles of acetic acid (CHX3COOH\ce{CH3COOH}): Acetic acid neutralizes NaOH\ce{NaOH} in a 1:11:1 stoichiometric ratio: CHX3COOH+NaOH→CHX3COONa+HX2O\ce{CH3COOH + NaOH -> CH3COONa + H2O}

    Volume of standardized NaOH\ce{NaOH} consumed: VNaOH=14.20 mL=0.01420 LV_{\ce{NaOH}} = 14.20\text{ mL} = 0.01420\text{ L}

    Using the unrounded molarity of NaOH\ce{NaOH} to avoid rounding errors: Moles of CHX3COOH=(0.01420 L)×(0.0491526 mol/L)≈6.9797×10−4 mol\text{Moles of } \ce{CH3COOH} = (0.01420\text{ L}) \times (0.0491526\text{ mol/L}) \approx 6.9797 \times 10^{-4}\text{ mol}

  2. Calculate the mass of acetic acid: Mass of CHX3COOH=(6.9797×10−4 mol)×60.05 g/mol≈0.041913 g\text{Mass of } \ce{CH3COOH} = (6.9797 \times 10^{-4}\text{ mol}) \times 60.05\text{ g/mol} \approx 0.041913\text{ g}
  3. Calculate the total mass of the waste stream sample aliquot: Using the volume and density of the aliquot: Mass of sample=Volume×Density=10.00 mL×1.005 g/mL=10.05 g\text{Mass of sample} = \text{Volume} \times \text{Density} = 10.00\text{ mL} \times 1.005\text{ g/mL} = 10.05\text{ g}

    Common Pitfall: Assuming the solution density is simply 1.00 g/mL1.00\text{ g/mL} without applying the given density (1.005 g/mL1.005\text{ g/mL}) will lead to a slight inaccuracy in the final percentage.

  4. Calculate the mass percent (% w/w\% \text{ w/w}): Mass %=Mass of CHX3COOHMass of Sample×100%=0.041913 g10.05 g×100%≈0.417%\text{Mass \%} = \frac{\text{Mass of } \ce{CH3COOH}}{\text{Mass of Sample}} \times 100\% = \frac{0.041913\text{ g}}{10.05\text{ g}} \times 100\% \approx 0.417\%

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets to use the solution density to find the solution mass and mistakenly assumes the 10.00 mL aliquot has a mass of 10.00 g, yielding an incorrect mass percent of 0.419%.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    n(KHP)=0.1852204.22=0.00090687 moln(\ce{KHP}) = \frac{0.1852}{204.22} = 0.00090687\text{ mol}

  2. Step 2

    M(NaOH)=0.000906870.01845=0.04915 MM(\ce{NaOH}) = \frac{0.00090687}{0.01845} = 0.04915\text{ M}

  3. Step 3

    n(CHX3COOH)=0.04915×0.01420=0.0006979 moln(\ce{CH3COOH}) = 0.04915 \times 0.01420 = 0.0006979\text{ mol}

  4. Step 4

    mass of CHX3COOH=0.0006979×60.05=0.04191 g\text{mass of } \ce{CH3COOH} = 0.0006979 \times 60.05 = 0.04191\text{ g}

  5. Step 5

    mass of solution=10.00 g\text{mass of solution} = 10.00\text{ g}

    Correct

    msolution=V×d=10.00 mL×1.005 g/mL=10.05 gm_{\text{solution}} = V \times d = 10.00\text{ mL} \times 1.005\text{ g/mL} = 10.05\text{ g}

    You equated the volume of the aliquot in milliliters directly to mass in grams, overlooking the given solution density of 1.005 g/mL1.005\text{ g/mL}.

  6. Step 6

    mass %=(0.0419110.00)×100%=0.419%\text{mass \%} = \left(\frac{0.04191}{10.00}\right) \times 100\% = 0.419\%

    Correct

    mass %=(0.04191 g10.05 g)×100%=0.417%\text{mass \%} = \left(\frac{0.04191\text{ g}}{10.05\text{ g}}\right) \times 100\% = 0.417\%

    Your percentage calculation method was correct, but the numerical answer was affected by using the unadjusted solution mass.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the molar concentration of the standardized titrant from the primary standard.

You accurately applied the 1:11:1 reaction stoichiometry to find the mass of acetic acid in the aliquot.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Density omission in mass-percent calculation

You treated the solution mass as equal to its volume, forgetting to multiply by the given density (1.005 g/mL1.005\text{ g/mL}).

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Assuming an aqueous solution's density is always 1.00 g/mL1.00\text{ g/mL} even when a non-unity density is explicitly specified in the problem statement.

REASONING PATH
Your ACEpath teacher’s suggested approach
Converting Solution Volume to Solution Mass
  • msolution=Vsolution×ρsolutionm_{\text{solution}} = V_{\text{solution}} \times \rho_{\text{solution}}

  • Always check whether a specific solution density is provided before assuming 1.00 mL=1.00 g1.00\text{ mL} = 1.00\text{ g}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. msolution=V×d=10.00 mL×1.005 g/mL=10.05 gm_{\text{solution}} = V \times d = 10.00\text{ mL} \times 1.005\text{ g/mL} = 10.05\text{ g}

  2. mass % (CHX3COOH)=msolutemsolution×100%=0.04191 g10.05 g×100%=0.4170%\text{mass \% } (\ce{CH3COOH}) = \frac{m_{\text{solute}}}{m_{\text{solution}}} \times 100\% = \frac{0.04191\text{ g}}{10.05\text{ g}} \times 100\% = 0.4170\%

Final answer

(a) [NaOH]=0.04915 M[\ce{NaOH}] = 0.04915\text{ M}; (b) Mass percent of CHX3COOH=0.417%\ce{CH3COOH} = 0.417\%

NEXT STEPS
Final Takeaways from Your Teacher
  • Highlight given physical properties like density upon first reading the problem so they are not bypassed during unit conversions.

  • Label quantities with explicit units (e.g., write 10.00 mL×1.005 g/mL10.00\text{ mL} \times 1.005\text{ g/mL}) to ensure dimensional consistency.

OverviewACEpath Teacher's Diagnosis

02 The student divides the moles of KHP by the 25.00 mL volume of water used to dissolve it instead of the 18.45 mL titrant volume, finding an incorrect NaOH molarity of 0.03627 M and carrying it downstream.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    n(KHP)=0.1852204.22=0.00090687 moln(\text{KHP}) = \frac{0.1852}{204.22} = 0.00090687\text{ mol}

  2. Step 2

    M(NaOH)=0.000906870.02500=0.03627 MM(\text{NaOH}) = \frac{0.00090687}{0.02500} = 0.03627\text{ M}

    Correct

    [NaOH]=9.0687×10−4 mol0.01845 L≈0.04915 M[\ce{NaOH}] = \frac{9.0687 \times 10^{-4}\text{ mol}}{0.01845\text{ L}} \approx 0.04915\text{ M}

    To determine the molarity of the titrant solution, you must divide the moles of NaOH\ce{NaOH} delivered by the volume of NaOH\ce{NaOH} titrant consumed (18.45 mL=0.01845 L18.45\text{ mL} = 0.01845\text{ L}), not by the volume of water used to dissolve the KHP solid (25.00 mL25.00\text{ mL}).

  3. Step 3

    n(CH3COOH)=0.03627×0.01420=0.0005150 moln(\text{CH}_3\text{COOH}) = 0.03627 \times 0.01420 = 0.0005150\text{ mol}

    Correct

    n(CHX3COOH)=0.0491526 M×0.01420 L≈6.9797×10−4 moln(\ce{CH3COOH}) = 0.0491526\text{ M} \times 0.01420\text{ L} \approx 6.9797 \times 10^{-4}\text{ mol}

    Your formula n=M×Vn = M \times V is correct, but the result is affected by the incorrect NaOH\ce{NaOH} concentration from Step 2.

  4. Step 4

    mass of CH3COOH=0.0005150×60.05=0.03093 g\text{mass of CH}_3\text{COOH} = 0.0005150 \times 60.05 = 0.03093\text{ g}

    Correct

    mass of CHX3COOH=(6.9797×10−4 mol)×60.05 g/mol≈0.04191 g\text{mass of } \ce{CH3COOH} = (6.9797 \times 10^{-4}\text{ mol}) \times 60.05\text{ g/mol} \approx 0.04191\text{ g}

    Your method of multiplying moles by the molar mass is correct, but your value reflects the earlier molarity error.

  5. Step 5

    mass of solution=10.00×1.005=10.05 g\text{mass of solution} = 10.00 \times 1.005 = 10.05\text{ g}

  6. Step 6

    mass %=0.0309310.05×100%=0.308%\text{mass \%} = \frac{0.03093}{10.05} \times 100\% = 0.308\%

    Correct

    mass %=0.041913 g10.05 g×100%≈0.417%\text{mass \%} = \frac{0.041913\text{ g}}{10.05\text{ g}} \times 100\% \approx 0.417\%

    Your calculation setup for mass percent is correct, but the final answer is shifted due to the initial molarity error.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the moles of KHP from its given mass and molar mass.

You correctly recognized the 1:11:1 stoichiometric ratios for both neutralization reactions.

You used the solution density properly to determine the total mass of the waste aliquot.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Incorrect Volume in Titrant Molarity Calculation

You accidentally selected the flask dissolution volume instead of the titrant volume dispensed from the buret.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the analyte solvent volume in the receiving flask with the titrant volume delivered from the buret. The volume of water used to dissolve a primary standard solid only serves as a reaction medium and does not affect the total moles of analyte or the concentration of the titrant solution.

REASONING PATH
Your ACEpath teacher’s suggested approach
Titrant Concentration Volume Rule
  • For a titrant BB dispensed from a buret: MB=nBVBM_B = \frac{n_B}{V_B}, where VBV_B is strictly the volume of titrant delivered.

  • Label all volumes clearly during setup with their identity (e.g., Vwater in flaskV_{\text{water in flask}} vs. VNaOH from buretV_{\text{NaOH from buret}}) to ensure the correct volume is placed in the denominator.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Recalculate [NaOH][\ce{NaOH}] using the titrant volume 18.45 mL18.45\text{ mL}: [NaOH]=9.0687×10−4 mol0.01845 L=0.049153 M[\ce{NaOH}] = \frac{9.0687 \times 10^{-4}\text{ mol}}{0.01845\text{ L}} = 0.049153\text{ M}.

  2. Find moles of acetic acid in 10.00 mL10.00\text{ mL}: n=(0.049153 M)(0.01420 L)=6.9797×10−4 moln = (0.049153\text{ M})(0.01420\text{ L}) = 6.9797 \times 10^{-4}\text{ mol}.

  3. Find mass of acetic acid: m=(6.9797×10−4 mol)(60.05 g/mol)=0.041913 gm = (6.9797 \times 10^{-4}\text{ mol})(60.05\text{ g/mol}) = 0.041913\text{ g}.

  4. Calculate mass percent: mass %=0.041913 g10.05 g×100%=0.417%\text{mass \%} = \frac{0.041913\text{ g}}{10.05\text{ g}} \times 100\% = 0.417\%.

Final answer

(a) [NaOH]=0.04915 M[\ce{NaOH}] = 0.04915\text{ M}; (b) Mass percent of CHX3COOH=0.417%\ce{CH3COOH} = 0.417\%

NEXT STEPS
Final Takeaways from Your Teacher
  • In standardization titrations, draw a quick schematic separating the buret contents from the Erlenmeyer flask contents.

  • Double-check that the volume used to compute a solution's concentration is the actual volume of that specific solution.

OverviewACEpath Teacher's Diagnosis

03 The student calculates the mass concentration (g/100 mL or % w/v) instead of mass percent (% w/w) by dividing the mass of acetic acid by the 10.00 mL solution volume.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    n(KHP)=0.1852204.22=0.00090687 mol  ⟹  M(NaOH)=0.000906870.01845=0.04915 Mn(\ce{KHP}) = \frac{0.1852}{204.22} = 0.00090687\text{ mol} \implies M(\ce{NaOH}) = \frac{0.00090687}{0.01845} = 0.04915\text{ M}

  2. Step 2

    n(CHX3COOH)=0.04915×0.01420=0.0006979 mol  ⟹  mass of CHX3COOH=0.0006979×60.05=0.04191 gn(\ce{CH3COOH}) = 0.04915 \times 0.01420 = 0.0006979\text{ mol} \implies \text{mass of } \ce{CH3COOH} = 0.0006979 \times 60.05 = 0.04191\text{ g}

  3. Step 3

    mass %=(0.0419110.00 mL)×100%=0.419%\text{mass \%} = \left(\frac{0.04191}{10.00\text{ mL}}\right) \times 100\% = 0.419\%

    Correct

    msample=10.00 mL×1.005 g/mL=10.05 g  ⟹  % w/w=(0.04191 g10.05 g)×100%=0.417%m_{\text{sample}} = 10.00\text{ mL} \times 1.005\text{ g/mL} = 10.05\text{ g} \implies \text{\% w/w} = \left(\frac{0.04191\text{ g}}{10.05\text{ g}}\right) \times 100\% = 0.417\%

    You divided the mass of acetic acid by the volume of the aliquot (10.00 mL10.00\text{ mL}) instead of the total mass of the aliquot. Mass percent (% w/w) requires dividing solute mass by sample mass, which you find by multiplying the volume by the given solution density (1.005 g/mL1.005\text{ g/mL}).

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the moles of KHP from its given mass and molar mass.

You accurately found the concentration of the NaOH\ce{NaOH} titrant to four significant figures.

You used the correct stoichiometric titration relationship to find the mass of acetic acid in the aliquot.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Mass percent vs. mass-volume concentration confusion

You divided by the sample volume in milliliters instead of calculating the total sample mass using the provided solution density.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing mass percent (% w/w, requiring mass/mass) with mass/volume concentration (% w/v, mass/volume), resulting in omitting the density conversion step for the waste stream aliquot.

REASONING PATH
Your ACEpath teacher’s suggested approach
Distinguish % w/w from % w/v
  • % w/w=mass of solute (g)mass of total solution (g)×100%\text{\% w/w} = \frac{\text{mass of solute (g)}}{\text{mass of total solution (g)}} \times 100\%, whereas % w/v=mass of solute (g)volume of solution (mL)×100%\text{\% w/v} = \frac{\text{mass of solute (g)}}{\text{volume of solution (mL)}} \times 100\%.

  • Whenever a problem specifies density and asks for mass percent (% w/w), always multiply the solution volume by its density before dividing.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate the total mass of the 10.00 mL10.00\text{ mL} aliquot using the given density: msample=10.00 mL×1.005 g/mL=10.05 gm_{\text{sample}} = 10.00\text{ mL} \times 1.005\text{ g/mL} = 10.05\text{ g}.

  2. Divide the solute mass by this total sample mass: % w/w=0.041913 g10.05 g×100%\text{\% w/w} = \frac{0.041913\text{ g}}{10.05\text{ g}} \times 100\%.

  3. Round the final percentage to three significant figures.

Final answer

(a) [NaOH]=0.04915 M[\ce{NaOH}] = 0.04915\text{ M}; (b) Mass percent of CHX3COOH=0.417%\ce{CH3COOH} = 0.417\%

NEXT STEPS
Final Takeaways from Your Teacher
  • Check units whenever calculating a percentage: ensure the numerator and denominator share the same dimension ([g]/[g][\text{g}] / [\text{g}] for % w/w).

  • Look for density in the problem prompt as an immediate cue that solution volume must be converted to solution mass.

Lock it in

Similar question

01

A 25.00 mL25.00\text{ mL} sample of an industrial wastewater solution with a density of 1.020 g/mL1.020\text{ g/mL} contains 0.1530 g0.1530\text{ g} of dissolved organic contaminant. Calculate the mass percent (% w/w) of the contaminant in the wastewater.

Answer

0.600%0.600\%. Mass of solution =25.00 mL×1.020 g/mL=25.50 g= 25.00\text{ mL} \times 1.020\text{ g/mL} = 25.50\text{ g}. Mass percent =(0.1530 g/25.50 g)×100%=0.600%= (0.1530\text{ g} / 25.50\text{ g}) \times 100\% = 0.600\%.

02

A 15.00 mL15.00\text{ mL} aliquot of vinegar (density 1.012 g/mL1.012\text{ g/mL}) is titrated with 0.2000 M NaOH0.2000\text{ M } \ce{NaOH}. If 38.25 mL38.25\text{ mL} of the base is required to reach the equivalence point (CHX3COOH+NaOH→CHX3COONa+HX2O\ce{CH3COOH + NaOH -> CH3COONa + H2O}), what is the mass percent (% w/w) of acetic acid (molar mass 60.05 g/mol60.05\text{ g/mol}) in the vinegar?

Answer

3.02%3.02\%. Moles of CHX3COOH=0.03825 L×0.2000 M=7.650×10−3 mol\ce{CH3COOH} = 0.03825\text{ L} \times 0.2000\text{ M} = 7.650 \times 10^{-3}\text{ mol}. Mass of CHX3COOH=7.650×10−3 mol×60.05 g/mol=0.4594 g\ce{CH3COOH} = 7.650 \times 10^{-3}\text{ mol} \times 60.05\text{ g/mol} = 0.4594\text{ g}. Mass of solution =15.00 mL×1.012 g/mL=15.18 g= 15.00\text{ mL} \times 1.012\text{ g/mL} = 15.18\text{ g}. Mass percent =(0.4594 g/15.18 g)×100%=3.026%≈3.03%= (0.4594\text{ g} / 15.18\text{ g}) \times 100\% = 3.026\% \approx 3.03\% (or 3.02%3.02\% using unrounded intermediate values).

03

An electroplating bath sample of volume 5.00 mL5.00\text{ mL} has a density of 1.180 g/mL1.180\text{ g/mL}. Neutralizing the sulfuric acid in this sample requires 22.40 mL22.40\text{ mL} of 0.1250 M NaOH0.1250\text{ M } \ce{NaOH} via the reaction HX2SOX4+2 NaOH→NaX2SOX4+2 HX2O\ce{H2SO4 + 2NaOH -> Na2SO4 + 2H2O}. Calculate the mass percent of HX2SOX4\ce{H2SO4} (molar mass 98.08 g/mol98.08\text{ g/mol}) in the bath to three significant figures.

Answer

2.33%2.33\%. Moles of NaOH=0.02240 L×0.1250 M=2.800×10−3 mol\ce{NaOH} = 0.02240\text{ L} \times 0.1250\text{ M} = 2.800 \times 10^{-3}\text{ mol}. Moles of HX2SOX4=2.800×10−3/2=1.400×10−3 mol\ce{H2SO4} = 2.800 \times 10^{-3} / 2 = 1.400 \times 10^{-3}\text{ mol}. Mass of HX2SOX4=1.400×10−3 mol×98.08 g/mol=0.1373 g\ce{H2SO4} = 1.400 \times 10^{-3}\text{ mol} \times 98.08\text{ g/mol} = 0.1373\text{ g}. Mass of solution =5.00 mL×1.180 g/mL=5.900 g= 5.00\text{ mL} \times 1.180\text{ g/mL} = 5.900\text{ g}. Mass percent =(0.1373 g/5.900 g)×100%=2.33%= (0.1373\text{ g} / 5.900\text{ g}) \times 100\% = 2.33\%.

Loading workspace…