Resources
In a municipal wastewater treatment demonstration, dissolved lead(II) ions are precipitated as lead(II) phosphate according to the balanced chemical equation: A batch of contaminated water contains of (molar mass ) in a tank. A technician treats this tank by adding of sodium phosphate (). Determine the limiting reactant and calculate the theoretical yield of solid lead(II) phosphate precipitate (, molar mass ) in milligrams.
Answer and steps
Final answer
Limiting reactant: ; Theoretical yield of
Steps
Calculate the moles of each reactant available
First, convert the mass of dissolved lead(II) ions () into millimoles ():
Each formula unit of sodium phosphate () dissociates completely in water to produce one phosphate ion ():
(Note: The solution volume of is context for the demonstration, but it is not needed to calculate amounts in moles since total quantities of reactants are directly given).
Determine the limiting reactant
From the balanced chemical equation:
The stoichiometric ratio requires of for every of .
To identify which reactant runs out first, divide each available amount by its stoichiometric coefficient:
- For :
- For :
Because yields fewer reaction cycles (), is the limiting reactant, and is in excess.
Calculate the theoretical yield of
The amount of product formed depends entirely on the limiting reactant. According to the reaction stoichiometry, of produce of :
Now, convert the amount of precipitate to mass in milligrams using its molar mass (, or ):
Rounding to three significant figures gives a theoretical yield of .
Typical errors
01 The student directly compares the initial mole amounts without accounting for stoichiometric coefficients, incorrectly identifying sodium phosphate as the limiting reactant because 2.50 mmol is less than 3.00 mmol.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
, so is the limiting reactant
Correct, so is the limiting reactant
You compared the raw molar amounts directly instead of dividing each by its stoichiometric coefficient from the balanced equation ( for and for ).
- Step 3Correct
Because you selected the wrong limiting reactant in Step 2, your resulting product moles and theoretical precipitate yield were carried forward from that error.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the available moles of both reactants.
You correctly multiplied your calculated moles of product by the molar mass to get mass in milligrams.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated the reactant with the smaller absolute number of moles as limiting, overlooking that the reaction consumes three ions for every two ions.
REASONING PATH
Your ACEpath teacher’s suggested approach- Stoichiometric Mole-Ratio Check
The limiting reactant is the one with the smallest value of .
Divide each available amount of reactant by its balanced coefficient before making any comparison.
CORRECTED PATH
ACEpath Teacher's DemonstrationDivide each mole amount by its coefficient: for , ; for , .
Identify as the limiting reactant because .
Calculate the precipitate moles from the limiting reactant: .
Calculate the theoretical precipitate mass: .
Limiting reactant: ; Theoretical yield:
02 The student assumes a 1:1 mole ratio between the limiting reactant Pb²⁺ and the precipitate Pb₃(PO₄)₂, forgetting to divide by the stoichiometric coefficient 3.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
According to the balanced reaction equation, of are required to form of . You assumed an equimolar ratio instead of dividing by the coefficient 3.
- Step 4Correct
Your multiplication method using molar mass was correct, but the calculation propagated the incorrect mole value from the previous step.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly converted the given mass of lead(II) ions into millimoles.
You used stoichiometric comparison ratios correctly to identify the limiting reactant.
You applied the correct molar mass to find the theoretical mass from moles.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou recognized the coefficient of 3 when finding the limiting reactant, but set it aside as a ratio when converting from reactant to product.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisOverlooking the stoichiometric conversion factor between the limiting reactant and the desired product when transitioning from reactant comparison to product yield.
REASONING PATH
Your ACEpath teacher’s suggested approach- Reactant-to-Product Mole Ratio
Theoretical yield of product in moles equals .
Always write out the dimensional analysis ratio explicitly before multiplying by molar mass.
CORRECTED PATH
ACEpath Teacher's DemonstrationUse the balanced chemical equation to set up the molar ratio: .
Multiply the precipitate's millimoles by its molar mass: .
Limiting reactant: ; Theoretical yield:
03 The student multiplies by the stoichiometric coefficient 3 instead of dividing when finding the amount of precipitate produced from the limiting reactant.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
According to the balanced equation, produce . You should multiply by the molar ratio (or divide by 3), rather than multiplying by 3.
- Step 4Correct
Your mass calculation correctly applied the molar mass formula, but the result was inflated because of the mole value from the previous step.
WHAT YOU DID WELL
Compliments from Your TeacherYou accurately converted the initial mass of lead(II) into millimoles.
You correctly identified as the limiting reactant by comparing mole-to-coefficient ratios.
You set up the final mass conversion using the correct molar mass.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou inverted the mole ratio between reactant and product, multiplying by the reactant coefficient 3 instead of applying the unit factor .
REASONING PATH
Your ACEpath teacher’s suggested approach- Forming the Stoichiometric Conversion Factor
When converting from substance A to substance B, multiply by .
Write out the full units with chemical formulas (e.g., ) so the unwanted unit cancels out.
CORRECTED PATH
ACEpath Teacher's DemonstrationLimiting reactant: ; Theoretical yield:
Lock it in
How do you identify the limiting reactant when given initial molar amounts of two reactants?
Divide each reactant's available moles by its stoichiometric coefficient in the balanced equation. The reactant with the lowest quotient is limiting.
Similar question
For the reaction , you react with . Which is the limiting reactant, and how many moles of can form?
Answer
is limiting; forms. Key steps: for , for . Since , is limiting. Theoretical moles .
A solution contains of and is mixed with of according to the reaction . Determine the limiting reactant and the mass of solid precipitate formed (molar mass of ).
Answer
is limiting; forms. Key steps: reaction equivalents for ; for . Moles of product . Mass .
You mix of with of according to . Find the limiting reactant and the theoretical yield of precipitate (molar mass ) in grams.
Answer
is limiting; forms. Key steps: , quotient ; , quotient . Since , limits. Yield .