Resources
Consider the mechanical and electrical properties of copper () through the lens of the electron sea model. Instead of determining conductivity, calculate the theoretical conduction electron density (in units of ) in a sample of pure copper, assuming each copper atom contributes exactly delocalized electron to the metallic conduction sea. The density of copper is , the molar mass of copper is , and Avogadro's constant is . Report the result to significant figures.
Answer and steps
Final answer
Steps
Relate Electron Density to Macroscopic Quantities
To find the conduction electron density using the electron sea model, we determine how many atoms are present per unit volume and multiply by the number of conduction electrons contributed per atom.
According to the electron sea model of metallic bonding, metal cations form a rigid periodic lattice while their valence electrons detach to form a delocalized "sea" of conduction electrons.
If each atom contributes free electrons, the conduction electron number density (electrons per cubic meter) is given by:
where is the number of atoms per unit volume ().
Express Atomic Number Density in Terms of Measured Properties
For a substance with density and molar mass :
- The mass of of copper is .
- The number of moles in is:
- Multiplying by Avogadro's constant gives the number of atoms per unit volume:
Combining this with the number of valence electrons per atom ():
Calculate the Conduction Electron Density
Substitute the given values into the formula, ensuring all units are consistent in the SI system:
Rounding to significant figures:
Common Pitfall: Ensure the molar mass is converted to kilograms per mole () to match the density given in . Using in without converting would result in an answer off by a factor of .
Typical errors
01 The student uses molar mass in grams per mole directly with density in kilograms per cubic meter without converting units, yielding an answer three orders of magnitude too small.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You substituted directly into the denominator without converting grams to kilograms. Because density is given in , the molar mass must be expressed in ( or ) to maintain consistent SI base units.
- Step 3Correct
Your arithmetic evaluation was correct for the substituted numbers, but the missing unit conversion propagated to produce an exponent of instead of .
WHAT YOU DID WELL
Compliments from Your TeacherYou selected the correct formula derived from the electron sea model relating atomic number density to conduction electron density.
You correctly recognized that each copper atom contributes exactly delocalized valence electron.
You performed the numerical division and scientific notation rounding accurately based on the numbers you plugged in.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou overlooked the unit mismatch between the mass unit in density () and the mass unit in standard molar mass (), leading to an uncancelled factor of .
REASONING PATH
Your ACEpath teacher’s suggested approach- Unit Alignment Check
Every composite formula involving physical quantities requires matching base units (e.g., both mass quantities in kilograms).
Always write out explicit units inside the substitution fraction: .
CORRECTED PATH
ACEpath Teacher's DemonstrationConvert the molar mass from to : .
Substitute into the expression: .
Evaluate the quotient: .
02 The student inverts the ratio of density and molar mass when attempting to calculate the number density.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You inverted the ratio of density and molar mass. Density divided by molar mass yields molar concentration (moles per cubic meter, ). Multiplying this by Avogadro's number gives atoms (and conduction electrons) per cubic meter: .
- Step 2Correct
You carried out the arithmetic accurately based on your initial formula, but the result is incorrect due to the inverted ratio in Step 1.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly used the molar mass converted to kilograms per mole () to ensure consistency with SI units.
You performed the numerical calculation accurately according to your written formula.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou accidentally placed molar mass in the numerator and mass density in the denominator instead of .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing molar volume (cubic meters per mole) with molar concentration (moles per cubic meter) when setting up number density.
REASONING PATH
Your ACEpath teacher’s suggested approach- Dimensional Analysis Check
Always track units through the formula: .
Check that your fraction simplifies to before multiplying by (particles per mole) to arrive at .
CORRECTED PATH
ACEpath Teacher's DemonstrationWrite the definition of number density: .
Express moles per volume using density and molar mass: .
Substitute into the formula: .
Substitute the given numerical values: .
03 The student assumes copper contributes 2 conduction electrons per atom based on its common Cu²⁺ oxidation state rather than the given 1 electron per atom.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You multiplied the atomic number density by electrons per atom. The problem explicitly specifies to assume each copper atom contributes exactly delocalized electron to the metallic conduction sea ().
- Step 2Correct
You substituted the correct numerical values with consistent SI units, but the calculation is doubled due to the initial factor of .
- Step 3Correct
Your arithmetic and significant figure rounding are consistent with your substituted expression, but the final value is twice the expected density.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly related macroscopic mass density and molar mass to calculate moles per unit volume.
You correctly used Avogadro's constant to convert moles to the number of atoms.
You properly converted the molar mass into SI units () to match the density units.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou may have automatically associated copper with its common ionic state () or misread the explicit condition given in the prompt.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the chemical valence/common oxidation state () with the specific conduction electron contribution () stipulated for this model of monovalent metallic conduction.
REASONING PATH
Your ACEpath teacher’s suggested approach- Check Problem Specifications for Conduction Contribution
In the free electron sea model, , where is the number of delocalized electrons contributed per atom.
Always read the prompt carefully to see whether a specific value of (such as for group 11 noble metals like , , ) is assigned rather than assuming the most common aqueous oxidation state.
CORRECTED PATH
ACEpath Teacher's DemonstrationSet the number of conduction electrons per copper atom to : .
Substitute the given values into the formula: .
Evaluate the quotient: .
Lock it in
Why must molar mass be converted to when calculating number density from density given in ?
To cancel mass units properly: . Using leaves an uncancelled factor of .
Similar question
Silver () has a density of and a molar mass of . Assuming each atom contributes conduction electron, calculate its conduction electron density in (). Round to 3 significant figures.
Answer
. Convert . Then .
Aluminum () has a density of and a molar mass of . In the electron sea model, aluminum contributes valence electrons per atom to the conduction band. Calculate the conduction electron density to 3 significant figures.
Answer
. Each atom contributes electrons. With , atomic density is . Then .
A monovalent metal has a conduction electron density of and a density of . What is its molar mass in standard laboratory units of ?
Answer
. Rearrange to find . Multiply by to get .