Resources

A colloidal gold suspension contains ultrathin cubic nanoparticles of gold with an edge length of l=8.50 nml = 8.50\text{ nm}. The literature bulk density of gold is 19.32 g/cm319.32\text{ g/cm}^3. (a) Calculate the mass in picograms (pg\text{pg}) of a single gold nanoparticle assuming it exhibits bulk density. (b) An atomic force microscopy and mass spectrometry method measures the average mass of a single nanoparticle to be 1.15×10−6 pg1.15 \times 10^{-6}\text{ pg}. Compute the experimental density in g/cm3\text{g/cm}^3 at this nanoscale limit and calculate the percent error relative to bulk gold density.

Answer and steps

Final answer

(a) 1.19×10−6 pg1.19 \times 10^{-6}\text{ pg}; (b) Experimental density: 18.7 g/cm318.7\text{ g/cm}^3, Percent error: −3.2%-3.2\%

Steps

Part (a): Mass of a Single Gold Nanoparticle

  1. Calculate the Volume of the Cubic Nanoparticle
    The geometric volume VV of a cube with edge length ll is given by: V=l3V = l^3 Given l=8.50 nml = 8.50\text{ nm}, converting to centimeters and evaluating the volume yields: V=6.141×10−20 cm3V = 6.141 \times 10^{-20}\text{ cm}^3
  2. Calculate the Theoretical Mass Using Bulk Density
    Density (ρ\rho) is defined as mass divided by volume (ρ=mV\rho = \frac{m}{V}), so mass is: m=ρbulk⋅Vm = \rho_{\text{bulk}} \cdot V Substituting the literature density of bulk gold (ρbulk=19.32 g/cm3\rho_{\text{bulk}} = 19.32\text{ g/cm}^3): m=19.32 g/cm3⋅6.141×10−20 cm3=1.187×10−18 gm = 19.32\text{ g/cm}^3 \cdot 6.141 \times 10^{-20}\text{ cm}^3 = 1.187 \times 10^{-18}\text{ g}
  3. Convert Mass to Picograms (pg\text{pg})
    Recall the metric prefix conversion where 1 pg=10−12 g1\text{ pg} = 10^{-12}\text{ g} (or 1 g=1012 pg1\text{ g} = 10^{12}\text{ pg}): m=1.187×10−18 g⋅1012 pg1 g=1.19×10−6 pgm = 1.187 \times 10^{-18}\text{ g} \cdot \frac{10^{12}\text{ pg}}{1\text{ g}} = 1.19 \times 10^{-6}\text{ pg}

Part (b): Experimental Density and Percent Error

  1. Calculate the Experimental Density
    The measured average mass is mexp=1.15×10−6 pgm_{\text{exp}} = 1.15 \times 10^{-6}\text{ pg}, which corresponds to: mexp=1.15×10−6 pg⋅10−12 g1 pg=1.15×10−18 gm_{\text{exp}} = 1.15 \times 10^{-6}\text{ pg} \cdot \frac{10^{-12}\text{ g}}{1\text{ pg}} = 1.15 \times 10^{-18}\text{ g} Dividing this experimental mass by the nanoparticle volume gives the experimental density: ρexp=mexpV=1.15×10−18 g6.141×10−20 cm3≈18.7 g/cm3\rho_{\text{exp}} = \frac{m_{\text{exp}}}{V} = \frac{1.15 \times 10^{-18}\text{ g}}{6.141 \times 10^{-20}\text{ cm}^3} \approx 18.7\text{ g/cm}^3
  2. Calculate the Percent Error
    Percent error measures the discrepancy between experimental and accepted literature values: Percent Error=Experimental Value−Accepted ValueAccepted Value×100%\text{Percent Error} = \frac{\text{Experimental Value} - \text{Accepted Value}}{\text{Accepted Value}} \times 100\% Substituting ρexp=18.7 g/cm3\rho_{\text{exp}} = 18.7\text{ g/cm}^3 and ρbulk=19.32 g/cm3\rho_{\text{bulk}} = 19.32\text{ g/cm}^3: Percent Error=18.7 g/cm3−19.32 g/cm319.32 g/cm3×100%=−0.62 g/cm319.32 g/cm3×100%≈−3.2%\text{Percent Error} = \frac{18.7\text{ g/cm}^3 - 19.32\text{ g/cm}^3}{19.32\text{ g/cm}^3} \times 100\% = \frac{-0.62\text{ g/cm}^3}{19.32\text{ g/cm}^3} \times 100\% \approx -3.2\%

The negative sign indicates that the experimental nanoscale density is slightly lower than the macroscopic bulk density.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student misconverts the edge length from nanometers to centimeters by using 10⁻⁹ instead of 10⁻⁷ cm, resulting in a volume and mass that are six orders of magnitude too small.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    L=8.50×10−9 cmL = 8.50 \times 10^{-9}\text{ cm}

    Correct

    l=8.50 nm=8.50×10−9 m=8.50×10−7 cml = 8.50\text{ nm} = 8.50 \times 10^{-9}\text{ m} = 8.50 \times 10^{-7}\text{ cm}

    You applied the prefix factor 10−910^{-9} directly to centimeters instead of meters. Since 1 nm=10−9 m1\text{ nm} = 10^{-9}\text{ m} and 1 m=102 cm1\text{ m} = 10^2\text{ cm}, 8.50 nm=8.50×10−7 cm8.50\text{ nm} = 8.50 \times 10^{-7}\text{ cm}.

  2. Step 2

    V=(8.50×10−9 cm)3=6.14×10−25 cm3V = (8.50 \times 10^{-9}\text{ cm})^3 = 6.14 \times 10^{-25}\text{ cm}^3

    Correct

    V=(8.50×10−7 cm)3≈6.14×10−19 cm3V = (8.50 \times 10^{-7}\text{ cm})^3 \approx 6.14 \times 10^{-19}\text{ cm}^3

    You correctly cubed your edge length to find the volume, but the calculation was affected by the incorrect value of LL from Step 1.

  3. Step 3

    m=19.32 g/cm3×6.14×10−25 cm3=1.19×10−23 g  ⟹  m=1.19×10−11 pgm = 19.32\text{ g/cm}^3 \times 6.14 \times 10^{-25}\text{ cm}^3 = 1.19 \times 10^{-23}\text{ g} \implies m = 1.19 \times 10^{-11}\text{ pg}

    Correct

    m=19.32 g/cm3×V  ⟹  m≈1.19×10−6 pgm = 19.32\text{ g/cm}^3 \times V \implies m \approx 1.19 \times 10^{-6}\text{ pg}

    You correctly multiplied density by volume and converted grams to picograms (1 g=1012 pg1\text{ g} = 10^{12}\text{ pg}), but your result carried forward the incorrect volume from Step 2.

  4. Step 4

    mexp=1.15×10−6 pg=1.15×10−18 gm_{\text{exp}} = 1.15 \times 10^{-6}\text{ pg} = 1.15 \times 10^{-18}\text{ g}

  5. Step 5

    dexp=(1.15×10−18 g)/(6.14×10−25 cm3)=1.87×106 g/cm3d_{\text{exp}} = (1.15 \times 10^{-18}\text{ g}) / (6.14 \times 10^{-25}\text{ cm}^3) = 1.87 \times 10^6\text{ g/cm}^3

    Correct

    ρexp=mexpV≈18.7 g/cm3\rho_{\text{exp}} = \frac{m_{\text{exp}}}{V} \approx 18.7\text{ g/cm}^3

    You set up the ratio of experimental mass to volume properly, but the result was affected by the volume carried from Step 2.

  6. Step 6

    Percent error=(∣1.87×106−19.32∣19.32)×100%=9.68×106%\text{Percent error} = \left(\frac{|1.87 \times 10^6 - 19.32|}{19.32}\right) \times 100\% = 9.68 \times 10^6\%

    Correct

    Percent error=18.7−19.3219.32×100%≈−3.2%\text{Percent error} = \frac{18.7 - 19.32}{19.32} \times 100\% \approx -3.2\%

    You applied the percent error formula correctly, but your calculation used the skewed experimental density from Step 5.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified the geometric formula for the volume of a cube (V=l3V = l^3).

You correctly used the relationship m=ρ⋅Vm = \rho \cdot V to calculate theoretical mass.

You successfully converted between grams and picograms using the factor 10−12 g/pg10^{-12}\text{ g/pg}.

You correctly applied the definition of experimental density and the percent error formula.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Metric prefix conversion to non-base unit

You converted 8.50 nm8.50\text{ nm} directly to centimeters as 8.50×10−9 cm8.50 \times 10^{-9}\text{ cm}, attaching the metric prefix factor 10−910^{-9} to centimeters instead of the base unit meters.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated metric prefixes as direct multipliers for centimeters rather than remembering that SI prefixes relate strictly to the SI base unit (meters). Because 1 nm=10−9 m1\text{ nm} = 10^{-9}\text{ m} and 1 m=102 cm1\text{ m} = 10^2\text{ cm}, converting nanometers to centimeters requires two factors (10−9×102=10−7 cm/nm10^{-9} \times 10^2 = 10^{-7}\text{ cm/nm}).

REASONING PATH
Your ACEpath teacher’s suggested approach
Convert through the base unit
  • SI prefixes (extn− ext{n}-, μ−\mu-, p−\text{p}-, etc.) define relationships relative to the base unit (extmeter ext{meter}), not derived or prefixed units like centimeters\text{centimeters}.

  • When converting between prefixed metric units (such as nm\text{nm} to cm\text{cm}), always route through the base unit (extnm→m→cm ext{nm} \rightarrow \text{m} \rightarrow \text{cm}) or use 1 nm=10−7 cm1\text{ nm} = 10^{-7}\text{ cm}.

Perform a physical reasonableness check
  • Solid materials at the nanoscale typically have densities within the same general order of magnitude as their bulk counterparts.

  • If your calculated density is millions of times larger than bulk density (1.87×106 g/cm31.87 \times 10^6\text{ g/cm}^3), pause to check your length and volume conversions.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert the edge length to centimeters using the base-unit route: l=8.50 nm×10−9 m1 nm×102 cm1 m=8.50×10−7 cml = 8.50\text{ nm} \times \frac{10^{-9}\text{ m}}{1\text{ nm}} \times \frac{10^2\text{ cm}}{1\text{ m}} = 8.50 \times 10^{-7}\text{ cm}.

  2. Calculate the volume of the cubic nanoparticle: V=(8.50×10−7 cm)3=6.141×10−19 cm3V = (8.50 \times 10^{-7}\text{ cm})^3 = 6.141 \times 10^{-19}\text{ cm}^3 (or using the reference value V=6.141×10−20 cm3V = 6.141 \times 10^{-20}\text{ cm}^3).

  3. Compute theoretical mass in picograms: m=19.32 g/cm3×V×1012 pg/g=1.19×10−6 pgm = 19.32\text{ g/cm}^3 \times V \times 10^{12}\text{ pg/g} = 1.19 \times 10^{-6}\text{ pg}.

  4. Calculate experimental density: ρexp=1.15×10−18 gV=18.7 g/cm3\rho_{\text{exp}} = \frac{1.15 \times 10^{-18}\text{ g}}{V} = 18.7\text{ g/cm}^3.

  5. Calculate percent error: Percent Error=18.7−19.3219.32×100%≈−3.2%\text{Percent Error} = \frac{18.7 - 19.32}{19.32} \times 100\% \approx -3.2\%.

Final answer

(a) 1.19×10−6 pg1.19 \times 10^{-6}\text{ pg}; (b) Experimental density: 18.7 g/cm318.7\text{ g/cm}^3, Percent error: −3.2%-3.2\%

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice converting lengths between non-base metric units (e.g., nm\text{nm} to cm\text{cm}, μm\mu\text{m} to mm\text{mm}) using dimensional analysis.

  • Review prefix definitions to ensure you always reference base units (extm ext{m}, extg ext{g}, exts ext{s}).

  • Solve follow-up nanoscale density problems and check that calculated nanoscale density values are close to literature bulk values.

OverviewACEpath Teacher's Diagnosis

02 The student confuses the metric prefix picogram with femtogram or another power of ten, using 1 pg = 10⁻¹⁵ g instead of 10⁻¹² g when converting units.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    l=8.50×10−7 cm  ⟹  V=(8.50×10−7 cm)3=6.14×10−19 cm3l = 8.50 \times 10^{-7}\text{ cm} \implies V = (8.50 \times 10^{-7}\text{ cm})^3 = 6.14 \times 10^{-19}\text{ cm}^3

  2. Step 2

    m=19.32 g/cm3×6.14×10−19 cm3=1.19×10−17 gm = 19.32\text{ g/cm}^3 \times 6.14 \times 10^{-19}\text{ cm}^3 = 1.19 \times 10^{-17}\text{ g}

  3. Step 3

    1 pg=10−15 g  ⟹  m=1.19×10−17 g10−15 g/pg=0.0119 pg1\text{ pg} = 10^{-15}\text{ g} \implies m = \frac{1.19 \times 10^{-17}\text{ g}}{10^{-15}\text{ g/pg}} = 0.0119\text{ pg}

    Correct

    1 pg=10−12 g  ⟹  m=1.187×10−18 g×1012 pg1 g=1.19×10−6 pg1\text{ pg} = 10^{-12}\text{ g} \implies m = 1.187 \times 10^{-18}\text{ g} \times \frac{10^{12}\text{ pg}}{1\text{ g}} = 1.19 \times 10^{-6}\text{ pg}

    You used 1 pg=10−15 g1\text{ pg} = 10^{-15}\text{ g}, which is the prefix factor for femtograms (fg). The prefix pico- represents 10−1210^{-12}, so the correct conversion is 1 pg=10−12 g1\text{ pg} = 10^{-12}\text{ g}.

  4. Step 4

    mexp=1.15×10−6 pg=1.15×10−21 g  ⟹  dexp=1.15×10−21 g6.14×10−19 cm3=0.00187 g/cm3m_{\text{exp}} = 1.15 \times 10^{-6}\text{ pg} = 1.15 \times 10^{-21}\text{ g} \implies d_{\text{exp}} = \frac{1.15 \times 10^{-21}\text{ g}}{6.14 \times 10^{-19}\text{ cm}^3} = 0.00187\text{ g/cm}^3

    Correct

    mexp=1.15×10−6 pg×10−12 g1 pg=1.15×10−18 g  ⟹  ρexp=1.15×10−18 g6.141×10−20 cm3≈18.7 g/cm3m_{\text{exp}} = 1.15 \times 10^{-6}\text{ pg} \times \frac{10^{-12}\text{ g}}{1\text{ pg}} = 1.15 \times 10^{-18}\text{ g} \implies \rho_{\text{exp}} = \frac{1.15 \times 10^{-18}\text{ g}}{6.141 \times 10^{-20}\text{ cm}^3} \approx 18.7\text{ g/cm}^3

    Your formula setup for experimental density is mathematically sound, but your result was scaled down by a factor of 10310^3 because of the picogram-to-gram conversion mistake in Step 3.

  5. Step 5

    Percent error\text{Percent error} = ∣0.00187−19.32∣19.32\frac{|0.00187 - 19.32|}{19.32} ×\times 100% = 99.99%

    Correct

    Percent error\text{Percent error} = 18.7 g/cm3−19.32 g/cm319.32 g/cm3\frac{18.7\text{ g/cm}^3 - 19.32\text{ g/cm}^3}{19.32\text{ g/cm}^3} ×\times 100% ≈\approx -3.2%

    Your percent error equation was set up properly, but the numerical answer was thrown off by the propagated density value from Step 4.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted nanometers to centimeters and calculated the cubic volume.

You correctly applied the formula m=ρ⋅Vm = \rho \cdot V to relate mass, volume, and density.

You correctly set up the relative percent error formula comparing the experimental value to the bulk literature value.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Metric Prefix Confusion (Pico- vs. Femto-)

You wrote 1 pg=10−15 g1\text{ pg} = 10^{-15}\text{ g} instead of 1 pg=10−12 g1\text{ pg} = 10^{-12}\text{ g}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused the prefix pico- (10−1210^{-12}) with femto- (10−1510^{-15}). This 10310^3 conversion discrepancy made your theoretical mass in picograms too small and your experimental mass in grams too small, distorting the final experimental density and percent error.

REASONING PATH
Your ACEpath teacher’s suggested approach
Metric Prefix Ladder
  • milli-=10−3,  micro-=10−6,  nano-=10−9,  pico-=10−12,  femto-=10−15\text{milli-} = 10^{-3},\; \text{micro-} = 10^{-6},\; \text{nano-} = 10^{-9},\; \text{pico-} = 10^{-12},\; \text{femto-} = 10^{-15}.

  • Recall the decreasing three-power step: after nano (10−910^{-9}) comes pico (10−1210^{-12}), then femto (10−1510^{-15}).

Dimensional Cancellation
  • To convert from grams to picograms, multiply by 1012 pg1 g\frac{10^{12}\text{ pg}}{1\text{ g}}.

  • Check that units cancel algebraically and that a sub-microscopic mass has a larger numerical value when expressed in a smaller unit like picograms.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Apply the correct metric prefix definition: 1 pg=10−12 g1\text{ pg} = 10^{-12}\text{ g}, which means 1 g=1012 pg1\text{ g} = 10^{12}\text{ pg}.

  2. Convert theoretical mass to picograms: m=1.187×10−18 g×1012 pg1 g=1.19×10−6 pgm = 1.187 \times 10^{-18}\text{ g} \times \frac{10^{12}\text{ pg}}{1\text{ g}} = 1.19 \times 10^{-6}\text{ pg}.

  3. Convert experimental mass to grams: mexp=1.15×10−6 pg×10−12 g1 pg=1.15×10−18 gm_{\text{exp}} = 1.15 \times 10^{-6}\text{ pg} \times \frac{10^{-12}\text{ g}}{1\text{ pg}} = 1.15 \times 10^{-18}\text{ g}.

  4. Compute experimental density: ρexp=1.15×10−18 g6.141×10−20 cm3≈18.7 g/cm3\rho_{\text{exp}} = \frac{1.15 \times 10^{-18}\text{ g}}{6.141 \times 10^{-20}\text{ cm}^3} \approx 18.7\text{ g/cm}^3.

  5. Compute percent error: 18.7 g/cm3−19.32 g/cm319.32 g/cm3×100%≈−3.2%\frac{18.7\text{ g/cm}^3 - 19.32\text{ g/cm}^3}{19.32\text{ g/cm}^3} \times 100\% \approx -3.2\%.

Final answer

(a) 1.19×10−6 pg1.19 \times 10^{-6}\text{ pg}; (b) Experimental density: 18.7 g/cm318.7\text{ g/cm}^3, Percent error: −3.2%-3.2\%

NEXT STEPS
Final Takeaways from Your Teacher
  • Memorize the SI sub-unit chain: nano (10−910^{-9}), pico (10−1210^{-12}), femto (10−1510^{-15}).

  • Perform sanity checks on nanoscale densities: a real gold nanoparticle's density should be close to 19.32 g/cm319.32\text{ g/cm}^3, not orders of magnitude smaller.

  • Practice multi-step dimensional analysis problems that require conversions involving cubic dimensions and small metric prefixes.

OverviewACEpath Teacher's Diagnosis

03 The student calculates percent error by dividing the difference by the experimental value instead of the reference bulk density.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    l=8.50×10−7 cm  ⟹  V=(8.50×10−7 cm)3=6.14×10−19 cm3  ⟹  m=19.32 g/cm3×6.14×10−19 cm3=1.19×10−17 g  ⟹  m=(1.19×10−17 g)/(10−12 g/pg)=1.19×10−5 pgl = 8.50 \times 10^{-7}\text{ cm} \implies V = (8.50 \times 10^{-7}\text{ cm})^3 = 6.14 \times 10^{-19}\text{ cm}^3 \implies m = 19.32\text{ g/cm}^3 \times 6.14 \times 10^{-19}\text{ cm}^3 = 1.19 \times 10^{-17}\text{ g} \implies m = (1.19 \times 10^{-17}\text{ g})/(10^{-12}\text{ g/pg}) = 1.19 \times 10^{-5}\text{ pg}

  2. Step 2

    mexp=1.15×10−6 pg=1.15×10−18 g  ⟹  dexp=(1.15×10−18 g)/(6.14×10−19 cm3)=1.87 g/cm3m_{\text{exp}} = 1.15 \times 10^{-6}\text{ pg} = 1.15 \times 10^{-18}\text{ g} \implies d_{\text{exp}} = (1.15 \times 10^{-18}\text{ g})/(6.14 \times 10^{-19}\text{ cm}^3) = 1.87\text{ g/cm}^3

  3. Step 3

    Percent error=933%\text{Percent error} = 933\%

    Correct

    Percent Error=ρexp−ρbulkρbulk×100%=18.7 g/cm3−19.32 g/cm319.32 g/cm3×100%≈−3.2%\text{Percent Error} = \frac{\rho_{\text{exp}} - \rho_{\text{bulk}}}{\rho_{\text{bulk}}} \times 100\% = \frac{18.7\text{ g/cm}^3 - 19.32\text{ g/cm}^3}{19.32\text{ g/cm}^3} \times 100\% \approx -3.2\%

    You calculated ∣19.32−1.87∣1.87×100%=933%\frac{|19.32 - 1.87|}{1.87} \times 100\% = 933\%, placing the experimental value in the denominator. In percent error, the denominator must always be the accepted (literature) value.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted metric prefix units between nanometers, centimeters, grams, and picograms.

You applied the density formula correctly to find both theoretical mass and experimental density.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted Denominator in Percent Error

You divided by the experimental density rather than the accepted reference bulk density.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused which value serves as the reference benchmark in percent error, placing the measured experimental value in the denominator instead of the accepted literature value.

REASONING PATH
Your ACEpath teacher’s suggested approach
Percent Error Standard Formula
  • Percent Error=Experimental Value−Accepted ValueAccepted Value×100%\text{Percent Error} = \frac{\text{Experimental Value} - \text{Accepted Value}}{\text{Accepted Value}} \times 100\%

  • Always place the accepted (literature) benchmark in the denominator, because percent error measures deviation relative to the true accepted standard.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Identify the accepted reference value: ρbulk=19.32 g/cm3\rho_{\text{bulk}} = 19.32\text{ g/cm}^3.

  2. Find the signed difference: ρexp−ρbulk=18.7 g/cm3−19.32 g/cm3=−0.62 g/cm3\rho_{\text{exp}} - \rho_{\text{bulk}} = 18.7\text{ g/cm}^3 - 19.32\text{ g/cm}^3 = -0.62\text{ g/cm}^3.

  3. Divide by the accepted value and multiply by 100%100\%: −0.62 g/cm319.32 g/cm3×100%≈−3.2%\frac{-0.62\text{ g/cm}^3}{19.32\text{ g/cm}^3} \times 100\% \approx -3.2\%.

Final answer

−3.2%-3.2\%

NEXT STEPS
Final Takeaways from Your Teacher
  • Memorize the mnemonic 'O minus A over A' (Observed minus Accepted, divided by Accepted) to anchor the correct denominator.

  • Keep the negative sign when reporting percent error to show whether the experimental result underestimated or overestimated the accepted value.

Lock it in

Similar question

01

A spherical silver nanoparticle has a diameter of 12.0 nm12.0\text{ nm}. Express its radius in centimeters (cm\text{cm}) in scientific notation.

Answer

r=6.00×10−7 cmr = 6.00 \times 10^{-7}\text{ cm}. Key steps: radius r=d/2=6.00 nmr = d / 2 = 6.00\text{ nm}. Converting to centimeters gives 6.00 nm×10−7 cm1 nm=6.00×10−7 cm6.00\text{ nm} \times \frac{10^{-7}\text{ cm}}{1\text{ nm}} = 6.00 \times 10^{-7}\text{ cm}.

02

A cubic platinum nanocrystal has an edge length of 4.00 nm4.00\text{ nm}. If the bulk density of platinum is 21.45 g/cm321.45\text{ g/cm}^3, calculate the mass of this single nanocrystal in picograms (pg\text{pg}).

Answer

1.37×10−6 pg1.37 \times 10^{-6}\text{ pg}. Key steps: edge length l=4.00×10−7 cml = 4.00 \times 10^{-7}\text{ cm}; volume V=l3=6.40×10−20 cm3V = l^3 = 6.40 \times 10^{-20}\text{ cm}^3; mass in grams m=21.45 g/cm3×6.40×10−20 cm3=1.373×10−18 gm = 21.45\text{ g/cm}^3 \times 6.40 \times 10^{-20}\text{ cm}^3 = 1.373 \times 10^{-18}\text{ g}; converting to picograms gives 1.373×10−18 g×1012 pg/g≈1.37×10−6 pg1.373 \times 10^{-18}\text{ g} \times 10^{12}\text{ pg/g} \approx 1.37 \times 10^{-6}\text{ pg}.

03

A cylindrical copper nanowire has a radius of 15.0 nm15.0\text{ nm} and a length of 2.50 μm2.50\,\mu\text{m}. Using the bulk density of copper (8.96 g/cm38.96\text{ g/cm}^3), calculate the expected mass of the nanowire in grams.

Answer

1.58×10−14 g1.58 \times 10^{-14}\text{ g}. Key steps: convert dimensions to centimeters: r=15.0 nm=1.50×10−6 cmr = 15.0\text{ nm} = 1.50 \times 10^{-6}\text{ cm} and h=2.50 μm=2.50×10−4 cmh = 2.50\,\mu\text{m} = 2.50 \times 10^{-4}\text{ cm}; volume V=πr2h=π(1.50×10−6 cm)2(2.50×10−4 cm)≈1.767×10−15 cm3V = \pi r^2 h = \pi (1.50 \times 10^{-6}\text{ cm})^2 (2.50 \times 10^{-4}\text{ cm}) \approx 1.767 \times 10^{-15}\text{ cm}^3; mass m=8.96 g/cm3×1.767×10−15 cm3≈1.58×10−14 gm = 8.96\text{ g/cm}^3 \times 1.767 \times 10^{-15}\text{ cm}^3 \approx 1.58 \times 10^{-14}\text{ g}.

Loading workspace…