Resources
A rigid reaction vessel contains a gaseous mixture of methane and chlorine at . In a kinetic trial, the initial quantities inside the vessel are of (molar mass ) and of (molar mass ). The elementary radical-propagation step exhibits a rate constant of . (a) Convert the masses of and into molar concentrations ( and ) in (). (b) If the instantaneous concentration of chlorine radical intermediates is , convert to . (c) Using collision-based rate law expressions, calculate the initial collision-limited reaction rate in .
Answer and steps
Final answer
(a) , so ; , so ; (b) ; (c) .
Steps
Part (a): Determining Molar Concentrations of and
- Convert the vessel volume to liters:
-
Calculate the moles and molarity of methane ():
- Convert mass from milligrams to grams:
- Find moles using the molar mass ():
- Determine molarity:
-
Calculate the moles and molarity of chlorine gas ():
- Convert mass from milligrams to grams:
- Find moles using the molar mass ():
- Determine molarity:
Part (b): Converting Intermediate Concentration to
The prefix milli- represents . Convert from to ():
Part (c): Calculating the Reaction Rate
According to collision theory, an elementary bimolecular reaction rate is directly proportional to the frequency of collisions between the two reacting species, represented by the product of their instantaneous molar concentrations:
Note: The molecular chlorine is a precursor for radical generation but is not a reactant in this specific elementary propagation step, so it does not enter this rate expression.
Substitute the known values:
Typical errors
01 The student forgets to convert the vessel volume from milliliters to liters when calculating molarity, resulting in concentrations that are a factor of 1000 too small.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
;
Correct;
You correctly converted both masses from milligrams to grams and found the correct moles (). However, you treated as in the denominator instead of converting it to , which made your calculated molar concentrations times too small.
- Step 2
- Step 3Correct
Your rate law setup and arithmetic were carried out correctly, but your final answer is off by a factor of due to propagating the incorrect from part (a).
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly converted milligrams to grams and computed the moles for both gases using their molar masses.
You correctly converted the concentration of from to .
You correctly selected the participating collision partners for the elementary step and evaluated the rate expression cleanly.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou wrote the unit next to the numerical value without dividing by .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConflating the numerical volume given in milliliters with liters leads to an unscaled denominator in the molarity formula , reducing all concentration terms by three orders of magnitude.
REASONING PATH
Your ACEpath teacher’s suggested approach- Verify Volume Units for Molarity
Molarity () requires volume in liters: .
Always explicitly convert milliliters to liters () before substituting into .
CORRECTED PATH
ACEpath Teacher's DemonstrationConvert volume:
Calculate :
Calculate :
Substitute the corrected into the rate expression:
(a) , ; (b) ; (c)
02 The student misinterprets the metric prefix milli- as 10⁶ instead of 10⁻³, multiplying by 10³ instead of dividing by 10³ when converting mmol/L to mol/L.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
The metric prefix milli- equals , so . Converting from a smaller unit (mmol) to a larger unit (mol) requires multiplying by (or dividing by ), but you multiplied by .
- Step 4Correct
Your algebraic substitution and arithmetic were carried out correctly, but the numerical answer is off by a factor of because of the converted radical concentration in Step 3.
WHAT YOU DID WELL
Compliments from Your TeacherYou converted mass values from milligrams to grams accurately.
You calculated molar concentrations by dividing moles by the volume in liters correctly.
You identified the correct reactants for the elementary bimolecular rate law and successfully excluded spectator species.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou treated millimoles as larger than moles by multiplying by instead of scaling down by .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisInverting the conversion factor between millimoles and moles leads to multiplying by instead of using the base definition .
REASONING PATH
Your ACEpath teacher’s suggested approach- Unit Dimensional Analysis
When going from a subunit with prefix milli- () to the base unit, multiply by .
Always write down the explicit unit cancellation factor: .
- Magnitude Sanity Check
A mole is a much larger quantity than a millimole, so the numerical value expressed in moles must always be smaller than in millimoles.
Check that your numerical exponent decreases by (e.g., ) when converting from to .
CORRECTED PATH
ACEpath Teacher's DemonstrationConvert the intermediate radical concentration: .
Substitute the corrected values into the collision rate law: .
Multiply the factors: .
03 The student substitutes the concentration of molecular chlorine [Cl₂] instead of the radical [Cl•] into the rate law expression.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3
- Step 4Correct
In an elementary reaction step, the collision rate depends directly on the colliding species in that specific step. The step is , so the reacting species is the radical , not molecular .
- Step 5Correct
You performed the multiplication correctly, but your numerical result was affected by substituting instead of .
WHAT YOU DID WELL
Compliments from Your TeacherYou converted both reactant masses into moles and calculated their correct initial molarities.
You executed the metric prefix conversion from to without error.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou accidentally selected the molecular precursor calculated in part (a) rather than the active colliding intermediate calculated in part (b).
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing a bulk molecular reagent with the active radical intermediate that actually collides and reacts in a specific elementary step.
REASONING PATH
Your ACEpath teacher’s suggested approach- Match Rate Law Directly to Colliding Reactants
For an elementary step , the rate law is , containing only the chemical species appearing on the reactant side of that step.
Always circle the exact chemical formulas on the reactant side of the given elementary equation before selecting concentration values.
CORRECTED PATH
ACEpath Teacher's DemonstrationIdentify the colliding reactants in the elementary step: and .
Write the collision-based rate law: .
Substitute the converted values: .
Multiply to evaluate the initial rate: .
Lock it in
What is the formal definition of molar concentration (molarity, ), and what specific unit must volume have?
. The volume must always be in liters (), not milliliters ().
Similar question
A flask contains of nitric oxide (, molar mass ). Calculate the molar concentration in .
Answer
. Volume . Thus, .
In a reaction chamber, the elementary bimolecular reaction occurs with rate constant . If the chamber contains of and of , determine the initial reaction rate in .
Answer
; . Reaction rate .
A gas-phase radical reaction step has . A rigid vessel holds of (molar mass ) and a transient hydrogen radical concentration of . Calculate the reaction rate in .
Answer
. . . Rate .