Resources

An electrolytic cell is configured to electroplate decorative nickel onto a metallic belt buckle using an aqueous solution of NiSO4\text{NiSO}_4. The cathode has a total surface area of 45.0 cm245.0\text{ cm}^2. A constant electrical current of 2.50 A2.50\text{ A} is passed through the cell for an operating duration of 35.0 minutes35.0\text{ minutes}. Assuming 100%100\% Faradaic current efficiency, calculate the resulting uniform thickness tt (in micrometers, μm\mu\text{m}) of the electroplated nickel layer. (Data: Faraday's constant F=96485 C/molF = 96485\text{ C/mol}; molar mass of nickel M=58.69 g/molM = 58.69\text{ g/mol}; density of solid nickel ρ=8.90 g/cm3\rho = 8.90\text{ g/cm}^3)

Answer and steps

Final answer

t=39.7 μmt = 39.7\text{ }\mu\text{m}

Steps

01

Identify the Cathode Half-Reaction

In an aqueous solution of nickel(II) sulfate (NiSOX4\ce{NiSO4}), nickel exists as divalent cations (NiX2+\ce{Ni^2+}). At the cathode (the belt buckle), reduction takes place according to the half-reaction:

NiX2+(aq)+2 eX−→Ni(s)\ce{Ni^2+ (aq) + 2e- -> Ni (s)}

This shows that z=2 moles of electronsz = 2\text{ moles of electrons} are required to deposit 1 mole of metallic nickel1\text{ mole of metallic nickel}.


02

Calculate the Total Electrical Charge Passed

Convert the electroplating duration into seconds:

ttime=35.0 min×60 s/min=2100 st_{\text{time}} = 35.0\text{ min} \times 60\text{ s/min} = 2100\text{ s}

Using the constant current I=2.50 AI = 2.50\text{ A}, the total charge QQ transferred is:

Q=I⋅ttime=2.50 A⋅2100 s=5250 CQ = I \cdot t_{\text{time}} = 2.50\text{ A} \cdot 2100\text{ s} = 5250\text{ C}


03

Determine the Mass of Electroplated Nickel

According to Faraday's law of electrolysis, the mass mm of nickel deposited at 100%100\% current efficiency is:

m=Q⋅Mz⋅Fm = \frac{Q \cdot M}{z \cdot F}

Substitute the given constants (M=58.69 g/molM = 58.69\text{ g/mol}, z=2z = 2, and F=96485 C/molF = 96485\text{ C/mol}):

m=5250 C⋅58.69 g/mol2⋅96485 C/mol≈1.597 gm = \frac{5250\text{ C} \cdot 58.69\text{ g/mol}}{2 \cdot 96485\text{ C/mol}} \approx 1.597\text{ g}


04

Relate Mass, Density, Area, and Coating Thickness

The electroplated layer forms a uniform solid volume VV over the total cathode surface area A=45.0 cm2A = 45.0\text{ cm}^2.

Using the density of nickel (ρ=8.90 g/cm3\rho = 8.90\text{ g/cm}^3):

V=mρ=A⋅tV = \frac{m}{\rho} = A \cdot t

Solve for the thickness tt in centimeters:

t=mρ⋅A=1.597 g8.90 g/cm3⋅45.0 cm2≈3.987×10−3 cmt = \frac{m}{\rho \cdot A} = \frac{1.597\text{ g}}{8.90\text{ g/cm}^3 \cdot 45.0\text{ cm}^2} \approx 3.987 \times 10^{-3}\text{ cm}


05

Convert to Micrometers (μm\mu\text{m})

Recall that 1 cm=10 000 μm1\text{ cm} = 10\,000\text{ }\mu\text{m} (or 104 μm10^4\text{ }\mu\text{m}):

t=3.987×10−3 cm×104 μm/cm≈39.7 μmt = 3.987 \times 10^{-3}\text{ cm} \times 10^4\text{ }\mu\text{m/cm} \approx 39.7\text{ }\mu\text{m}

Common Pitfall: Forgetting to convert the time to seconds before calculating Q=I⋅ttimeQ = I \cdot t_{\text{time}}, or omitting the factor of z=2z = 2 for the divalent ion NiX2+\ce{Ni^2+}, which leads to an overestimation of the deposited mass by a factor of two.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student assumes a 1:1 electron stoichiometry (n = 1) for nickel reduction instead of recognizing the divalent Ni²⁺ cation, doubling the calculated mass and thickness.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Q=2.50 A⋅(2100 s)=5250 CQ = 2.50\text{ A} \cdot (2100\text{ s}) = 5250\text{ C}

  2. Step 2

    nNi=5250 C96485 C/mol≈0.05441 moln_{\text{Ni}} = \frac{5250\text{ C}}{96485\text{ C/mol}} \approx 0.05441\text{ mol}

    Correct

    nNi=QzF=5250 C2×96485 C/mol≈0.02721 moln_{\text{Ni}} = \frac{Q}{zF} = \frac{5250\text{ C}}{2 \times 96485\text{ C/mol}} \approx 0.02721\text{ mol}

    In aqueous NiSOX4\ce{NiSO4}, nickel exists as divalent cations (NiX2+\ce{Ni^2+}). The reduction half-reaction is NiX2++2 eX−→Ni\ce{Ni^2+ + 2e- -> Ni}, so each mole of nickel requires z=2 moles of electronsz = 2\text{ moles of electrons}, not 11.

  3. Step 3

    m=0.05441 mol⋅58.69 g/mol≈3.193 gm = 0.05441\text{ mol} \cdot 58.69\text{ g/mol} \approx 3.193\text{ g}

    Correct

    m=nNi⋅M=0.02721 mol×58.69 g/mol≈1.597 gm = n_{\text{Ni}} \cdot M = 0.02721\text{ mol} \times 58.69\text{ g/mol} \approx 1.597\text{ g}

    You correctly multiplied moles by molar mass, but the value was doubled due to the earlier stoichiometry error.

  4. Step 4

    V=3.193 g/8.90 g/cm3≈0.3588 cm3V = 3.193\text{ g} / 8.90\text{ g/cm}^3 \approx 0.3588\text{ cm}^3

    Correct

    V=mρ=1.597 g8.90 g/cm3≈0.1794 cm3V = \frac{m}{\rho} = \frac{1.597\text{ g}}{8.90\text{ g/cm}^3} \approx 0.1794\text{ cm}^3

    You correctly applied the density relationship V=mρV = \frac{m}{\rho}, propagating the doubled mass.

  5. Step 5

    t=0.3588 cm3/45.0 cm2≈0.00797 cm=79.7 μmt = 0.3588\text{ cm}^3 / 45.0\text{ cm}^2 \approx 0.00797\text{ cm} = 79.7\text{ }\mu\text{m}

    Correct

    t=VA=0.1794 cm345.0 cm2≈3.987×10−3 cm=39.7 μmt = \frac{V}{A} = \frac{0.1794\text{ cm}^3}{45.0\text{ cm}^2} \approx 3.987 \times 10^{-3}\text{ cm} = 39.7\text{ }\mu\text{m}

    You correctly divided volume by area and converted centimeters to micrometers, but the final thickness is twice the true value due to the initial stoichiometry error.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted the time from minutes to seconds.

You calculated the total charge Q=I⋅tQ = I \cdot t accurately.

You correctly related mass, density, surface area, and coating thickness.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omission of Electron Stoichiometry in Faraday's Law

You divided charge directly by Faraday's constant (Q/FQ/F) instead of accounting for the two-electron reduction (Q/2FQ/2F).

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Forgetting to write down the cathode half-reaction led to assuming a 1:11:1 mole ratio between electrons and deposited nickel metal atoms.

REASONING PATH
Your ACEpath teacher’s suggested approach
Cathode Half-Reaction Check
  • Always write out the cathode reduction half-reaction: MXz++z eX−→M(s)\ce{M^{z+} + z e- -> M(s)} to identify zz.

  • Before applying Faraday's law, verify the oxidation state of the metal cation in the salt to determine zz.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write the cathode half-reaction: NiX2+(aq)+2 eX−→Ni(s)\ce{Ni^2+ (aq) + 2e- -> Ni (s)}, which requires z=2z = 2.

  2. Calculate moles of nickel: nNi=QzF=5250 C2×96485 C/mol≈0.02721 moln_{\text{Ni}} = \frac{Q}{zF} = \frac{5250\text{ C}}{2 \times 96485\text{ C/mol}} \approx 0.02721\text{ mol}.

  3. Find the mass: m=0.02721 mol×58.69 g/mol≈1.597 gm = 0.02721\text{ mol} \times 58.69\text{ g/mol} \approx 1.597\text{ g}.

  4. Determine the volume: V=1.597 g8.90 g/cm3≈0.1794 cm3V = \frac{1.597\text{ g}}{8.90\text{ g/cm}^3} \approx 0.1794\text{ cm}^3.

  5. Compute the thickness: t=0.1794 cm345.0 cm2≈3.987×10−3 cm=39.7 μmt = \frac{0.1794\text{ cm}^3}{45.0\text{ cm}^2} \approx 3.987 \times 10^{-3}\text{ cm} = 39.7\text{ }\mu\text{m}.

Final answer

t=39.7 μmt = 39.7\text{ }\mu\text{m}

NEXT STEPS
Final Takeaways from Your Teacher
  • Write the balanced reduction half-reaction at the start of every electrolysis problem.

  • Identify the number of transferred electrons zz explicitly before calculating moles from electric charge.

OverviewACEpath Teacher's Diagnosis

02 The student forgets to convert the time from minutes to seconds when calculating total electric charge, underestimating the deposited thickness by a factor of 60.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Q=2.50 A⋅35.0 min=87.5 CQ = 2.50\text{ A} \cdot 35.0\text{ min} = 87.5\text{ C}

    Correct

    Q=I⋅t=2.50 A⋅(35.0⋅60 s)=5250 CQ = I \cdot t = 2.50\text{ A} \cdot (35.0 \cdot 60\text{ s}) = 5250\text{ C}

    You multiplied current directly by minutes instead of converting to seconds. Because 1 C=1 A⋅s1\text{ C} = 1\text{ A}\cdot\text{s}, the time duration must be expressed in seconds (35.0 min×60 s/min=2100 s35.0\text{ min} \times 60\text{ s/min} = 2100\text{ s}).

  2. Step 2

    nNi=87.5 C/(2⋅96485 C/mol)≈0.0004534 moln_{\text{Ni}} = 87.5\text{ C} / (2 \cdot 96485\text{ C/mol}) \approx 0.0004534\text{ mol}

    Correct

    nNi=5250 C2⋅96485 C/mol≈0.02721 moln_{\text{Ni}} = \frac{5250\text{ C}}{2 \cdot 96485\text{ C/mol}} \approx 0.02721\text{ mol}

    You correctly recognized that reducing NiX2+\ce{Ni^2+} requires 2 mol e−2\text{ mol } e^- per mole of nickel and properly used Faraday's constant, but this calculation inherits the incorrect charge from Step 1.

  3. Step 3

    m=0.0004534 mol⋅58.69 g/mol≈0.02661 gm = 0.0004534\text{ mol} \cdot 58.69\text{ g/mol} \approx 0.02661\text{ g}

    Correct

    m=0.02721 mol⋅58.69 g/mol≈1.597 gm = 0.02721\text{ mol} \cdot 58.69\text{ g/mol} \approx 1.597\text{ g}

    You correctly multiplied moles by the molar mass of nickel, but the value is scaled down by the earlier unit error.

  4. Step 4

    V=0.02661 g/(8.90 g/cm3)≈0.002990 cm3V = 0.02661\text{ g} / (8.90\text{ g/cm}^3) \approx 0.002990\text{ cm}^3

    Correct

    V=1.597 g8.90 g/cm3≈0.1794 cm3V = \frac{1.597\text{ g}}{8.90\text{ g/cm}^3} \approx 0.1794\text{ cm}^3

    You correctly used density to find the volume of the nickel deposit, but the mass carried forward was too small.

  5. Step 5

    t=0.002990 cm3/45.0 cm2≈0.0000664 cm=0.664 μmt = 0.002990\text{ cm}^3 / 45.0\text{ cm}^2 \approx 0.0000664\text{ cm} = 0.664\text{ }\mu\text{m}

    Correct

    t=0.1794 cm345.0 cm2≈3.987×10−3 cm=39.7 μmt = \frac{0.1794\text{ cm}^3}{45.0\text{ cm}^2} \approx 3.987 \times 10^{-3}\text{ cm} = 39.7\text{ }\mu\text{m}

    You correctly divided the layer volume by the cathode surface area and accurately converted centimeters to micrometers (1 cm=104 μm1\text{ cm} = 10^4\text{ }\mu\text{m}), but the resulting thickness is 6060 times too small due to Step 1.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified the 22-electron reduction requirement for NiX2+\ce{Ni^2+}.

You used Faraday's constant, molar mass, and density in the correct positions.

You converted centimeters to micrometers with the correct conversion factor.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Time Unit Conversion Omission in Coulomb Definition

You treated minutes as seconds when computing Q=I⋅tQ = I \cdot t, yielding ampere-minutes instead of coulombs (1 C=1 A⋅s1\text{ C} = 1\text{ A}\cdot\text{s}).

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Overlooking the SI definition of the coulomb (1 C=1 A⋅s1\text{ C} = 1\text{ A}\cdot\text{s}) during the initial charge calculation causes an unscaled factor of 6060 to propagate through every subsequent mass, volume, and thickness value.

REASONING PATH
Your ACEpath teacher’s suggested approach
Coulomb Base Unit Check
  • Electrical charge in coulombs requires time in seconds: Q (C)=I (A)×t (s)Q\text{ (C)} = I\text{ (A)} \times t\text{ (s)}.

  • Always convert operating duration (minutes or hours) to seconds before multiplying by current in amperes.

Ion Valence Check
  • A divalent cation MX2+\ce{M^{2+}} requires z=2z = 2 moles of electrons per mole of metal deposited.

  • Keep the z=2z = 2 factor in the denominator of Faraday's law (n=QzFn = \frac{Q}{zF}).

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert duration to seconds: t=35.0 min×60 s/min=2100 st = 35.0\text{ min} \times 60\text{ s/min} = 2100\text{ s}.

  2. Calculate total charge: Q=2.50 A×2100 s=5250 CQ = 2.50\text{ A} \times 2100\text{ s} = 5250\text{ C}.

  3. Compute deposited nickel moles: n=5250 C2×96485 C/mol≈0.02721 moln = \frac{5250\text{ C}}{2 \times 96485\text{ C/mol}} \approx 0.02721\text{ mol}.

  4. Determine mass: m=0.02721 mol×58.69 g/mol≈1.597 gm = 0.02721\text{ mol} \times 58.69\text{ g/mol} \approx 1.597\text{ g}.

  5. Determine thickness: t=mρ⋅A=1.597 g8.90 g/cm3×45.0 cm2≈3.987×10−3 cm=39.7 μmt = \frac{m}{\rho \cdot A} = \frac{1.597\text{ g}}{8.90\text{ g/cm}^3 \times 45.0\text{ cm}^2} \approx 3.987 \times 10^{-3}\text{ cm} = 39.7\text{ }\mu\text{m}.

Final answer

t=39.7 μmt = 39.7\text{ }\mu\text{m}

NEXT STEPS
Final Takeaways from Your Teacher
  • Write out explicit unit labels with conversion fractions during the first step (e.g., A⋅min⋅60 s1 min\text{A} \cdot \text{min} \cdot \frac{60\text{ s}}{1\text{ min}}) to ensure units cancel cleanly to coulombs.

  • Check whether the final thickness is physically reasonable for electroplating (typically 10–50 μm10\text{--}50\text{ }\mu\text{m} for protective coatings, whereas 0.66 μm0.66\text{ }\mu\text{m} is unusually thin for a 35-minute run at 2.5 A).

OverviewACEpath Teacher's Diagnosis

03 The student incorrectly multiplies the volume of nickel by the surface area rather than dividing by it to determine thickness.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Q=2.50 A⋅2100 s=5250 CQ = 2.50\text{ A} \cdot 2100\text{ s} = 5250\text{ C}

  2. Step 2

    m=5250 C⋅58.69 g/mol2⋅96485 C/mol≈1.597 gm = \frac{5250\text{ C} \cdot 58.69\text{ g/mol}}{2 \cdot 96485\text{ C/mol}} \approx 1.597\text{ g}

  3. Step 3

    V=1.597 g8.90 g/cm3≈0.1794 cm3V = \frac{1.597\text{ g}}{8.90\text{ g/cm}^3} \approx 0.1794\text{ cm}^3

  4. Step 4

    t=0.1794 cm3⋅45.0 cm2≈8.07 cm=80700 μmt = 0.1794\text{ cm}^3 \cdot 45.0\text{ cm}^2 \approx 8.07\text{ cm} = 80700\text{ }\mu\text{m}

    Correct

    t=VA=0.1794 cm345.0 cm2≈3.987×10−3 cm=39.9 μmt = \frac{V}{A} = \frac{0.1794\text{ cm}^3}{45.0\text{ cm}^2} \approx 3.987 \times 10^{-3}\text{ cm} = 39.9\text{ }\mu\text{m} (or 39.7 μm39.7\text{ }\mu\text{m} unrounded)

    Because volume equals area times thickness (V=A⋅tV = A \cdot t), the thickness must be found by dividing volume by area (t=VAt = \frac{V}{A}), not by multiplying them. Multiplying gives units of cm5\text{cm}^5 rather than cm\text{cm}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted the operating time from minutes into seconds.

You set up and evaluated Faraday's law using the correct charge number of z=2z = 2 for nickel.

You used the density of nickel to convert mass into volume accurately.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Geometric inversion in coating thickness formula

You accidentally multiplied the nickel volume by the cathode surface area instead of dividing by it.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You misapplied the geometric relationship between volume, surface area, and thickness (V=A⋅tV = A \cdot t). When rearranging for thickness, dividing both sides by area yields t=VAt = \frac{V}{A}. Checking the physical units (cm3/cm2=cm\text{cm}^3 / \text{cm}^2 = \text{cm}) confirms the correct operation.

REASONING PATH
Your ACEpath teacher’s suggested approach
Geometric Definition of Layer Thickness
  • For a uniform coating of area AA and thickness tt, the total volume is V=A⋅tV = A \cdot t, which rearranges to t=VAt = \frac{V}{A}.

  • Always isolate thickness by dividing the total volume by the electroplated surface area: t=VAt = \frac{V}{A}.

Dimensional Unit Check
  • Multiplying volume by area yields cm3×cm2=cm5\text{cm}^3 \times \text{cm}^2 = \text{cm}^5, whereas dividing yields cm3/cm2=cm\text{cm}^3 / \text{cm}^2 = \text{cm}.

  • Check the resulting dimensional units before converting to micrometers to ensure the expression represents a true linear distance.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Use the uniform layer volume relation: V=A⋅t  ⟹  t=VAV = A \cdot t \implies t = \frac{V}{A}.

  2. Substitute V=0.1794 cm3V = 0.1794\text{ cm}^3 and A=45.0 cm2A = 45.0\text{ cm}^2: t=0.1794 cm345.0 cm2≈3.987×10−3 cmt = \frac{0.1794\text{ cm}^3}{45.0\text{ cm}^2} \approx 3.987 \times 10^{-3}\text{ cm}.

  3. Convert centimeters to micrometers using 1 cm=104 μm1\text{ cm} = 10^4\text{ }\mu\text{m}: t=3.987×10−3 cm×104 μm/cm≈39.7 μmt = 3.987 \times 10^{-3}\text{ cm} \times 10^4\text{ }\mu\text{m/cm} \approx 39.7\text{ }\mu\text{m} (or 39.9 μm39.9\text{ }\mu\text{m} using intermediate rounding).

Final answer

t=39.7 μmt = 39.7\text{ }\mu\text{m}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the rearrangement of V=A⋅tV = A \cdot t to ensure you divide volume by area whenever finding layer thickness.

  • Perform a quick unit balance check on intermediate equations before proceeding to unit conversions.

Lock it in

Similar question

01

A current of 1.50 A1.50\text{ A} is passed through an aqueous AgNOX3\ce{AgNO3} solution for 40.0 minutes40.0\text{ minutes}. Calculate the mass of silver deposited at the cathode. (MAg=107.87 g/molM_{\text{Ag}} = 107.87\text{ g/mol}, F=96485 C/molF = 96485\text{ C/mol})

Answer

m=4.02 gm = 4.02\text{ g}. Silver deposits as AgX++eX−→Ag\ce{Ag+ + e- -> Ag} (z=1z = 1). Q=1.50 A×2400 s=3600 CQ = 1.50\text{ A} \times 2400\text{ s} = 3600\text{ C}. m=3600 C×107.87 g/mol1×96485 C/mol≈4.02 gm = \frac{3600\text{ C} \times 107.87\text{ g/mol}}{1 \times 96485\text{ C/mol}} \approx 4.02\text{ g}.

02

An object with a total surface area of 60.0 cm260.0\text{ cm}^2 is electroplated with copper from an aqueous CuSOX4\ce{CuSO4} bath using a current of 3.00 A3.00\text{ A} for 20.0 minutes20.0\text{ minutes}. Determine the thickness of the copper coating in micrometers. (Density of copper ρ=8.96 g/cm3\rho = 8.96\text{ g/cm}^3, MCu=63.55 g/molM_{\text{Cu}} = 63.55\text{ g/mol}, F=96485 C/molF = 96485\text{ C/mol})

Answer

t=22.0 μmt = 22.0\text{ }\mu\text{m}. Copper reduction: CuX2++2 eX−→Cu\ce{Cu^2+ + 2e- -> Cu} (z=2z = 2). Q=3.00 A×1200 s=3600 CQ = 3.00\text{ A} \times 1200\text{ s} = 3600\text{ C}. m=3600×63.552×96485≈1.185 gm = \frac{3600 \times 63.55}{2 \times 96485} \approx 1.185\text{ g}. V=1.185 g8.96 g/cm3≈0.1323 cm3V = \frac{1.185\text{ g}}{8.96\text{ g/cm}^3} \approx 0.1323\text{ cm}^3. t=0.1323 cm360.0 cm2≈2.205×10−3 cm=22.0 μmt = \frac{0.1323\text{ cm}^3}{60.0\text{ cm}^2} \approx 2.205 \times 10^{-3}\text{ cm} = 22.0\text{ }\mu\text{m}.

03

A decorative trophy with surface area 120.0 cm2120.0\text{ cm}^2 is plated with gold from a solution of KAu(CN)X2\ce{KAu(CN)2} containing gold(I) ions at a current efficiency of 92.0%92.0\%. To achieve a uniform thickness of 5.00 μm5.00\text{ }\mu\text{m}, how many minutes must a current of 1.80 A1.80\text{ A} be applied? (Density of gold ρ=19.3 g/cm3\rho = 19.3\text{ g/cm}^3, MAu=197.0 g/molM_{\text{Au}} = 197.0\text{ g/mol}, F=96485 C/molF = 96485\text{ C/mol})

Answer

ttime=11.2 minutest_{\text{time}} = 11.2\text{ minutes}. For AuX+\ce{Au+} (z=1z = 1): Volume V=120.0 cm2×(5.00×10−4 cm)=0.0600 cm3V = 120.0\text{ cm}^2 \times (5.00 \times 10^{-4}\text{ cm}) = 0.0600\text{ cm}^3. Mass m=0.0600 cm3×19.3 g/cm3=1.158 gm = 0.0600\text{ cm}^3 \times 19.3\text{ g/cm}^3 = 1.158\text{ g}. Theoretical charge Qth=1.158 g×1×96485 C/mol197.0 g/mol≈567.1 CQ_{\text{th}} = \frac{1.158\text{ g} \times 1 \times 96485\text{ C/mol}}{197.0\text{ g/mol}} \approx 567.1\text{ C}. Actual charge Q=567.1 C0.920≈616.4 CQ = \frac{567.1\text{ C}}{0.920} \approx 616.4\text{ C}. Time ttime=616.4 C1.80 A≈342.4 s≈5.71 mint_{\text{time}} = \frac{616.4\text{ C}}{1.80\text{ A}} \approx 342.4\text{ s} \approx 5.71\text{ min} (or ≈5.7 min\approx 5.7\text{ min}).

Loading workspace…