Resources
A standard laboratory water treatment protocol requires evaluating the single-replacement reactivity of granular iron () against toxic heavy-metal contamination. An environmental aqueous effluent sample contains (parts per million by mass, where assuming a solution density of ) of lead(II) nitrate, (molar mass ). A technician adds solid iron turnings to a batch of this effluent. Assuming stoichiometric completion according to the periodic activity series via , calculate: (a) the initial molar concentration of in , and (b) the theoretical mass in milligrams of solid iron consumed.
Answer and steps
Final answer
(a) ; (b) . Conversion: of . Molarity of . In , total moles of . From the mole ratio, moles of . Mass of .
Steps
Part (a): Determine the initial molar concentration of
- Convert the concentration from parts per million () to grams per liter (): Given that for dilute aqueous solutions:
- Calculate the molarity of : Using the molar mass of ():
- Find the concentration of ions: Lead(II) nitrate dissociates completely in water according to: Because each mole of dissolved produces of :
Part (b): Calculate the mass of solid iron consumed
- Calculate the total moles of in the solution:
- Determine the moles of required using stoichiometry: According to the periodic activity series, iron is more electropositive (more reactive) than lead and readily oxidizes, yielding the single-replacement reaction: The mole ratio between and is :
- Convert moles of to mass in milligrams: Using the atomic weight of iron ():
Common Pitfall: Remember to base the mole calculation on the molar mass of the entire salt (, ) rather than elemental lead (, ), because the given refers to the dissolved solute compound.
Typical errors
01 The student forgets to multiply the concentration of lead ions by the volume of effluent, calculating the iron required for 1.00 L instead of 2.50 L.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You treated the concentration in as the total moles present in the entire sample. Because the batch has a volume of , you need to multiply the concentration by the volume: .
- Step 3Correct
Your formula and atomic weight for iron were correct, but your final mass was affected by using the unscaled mole quantity from the previous step.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly interpreted as for dilute aqueous solutions.
You correctly used the molar mass of the full compound to determine the molarity.
You correctly identified the stoichiometric mole ratio between and .
You correctly converted moles to milligrams using the atomic mass of iron.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConflating molar concentration (, in ) with total amount of substance (, in ) by omitting the volume factor .
REASONING PATH
Your ACEpath teacher’s suggested approach- Amount vs. Concentration Check
(moles equal molarity multiplied by solution volume in liters).
Always verify units before setting up a stoichiometric ratio: concentration () cannot be equated directly to an amount in unless .
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate the total moles of in : .
Apply the stoichiometric ratio from : .
Calculate the mass of iron: .
(a) ; (b)
02 The student uses the atomic mass of lead instead of the molar mass of lead(II) nitrate when converting parts per million to molar concentration.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
The problem states that the effluent contains of the compound , not elemental lead. You need to divide the mass concentration by the formula mass of lead(II) nitrate () rather than the atomic mass of lead ().
- Step 2Correct
Your method of multiplying concentration by volume and applying the stoichiometric ratio from is completely correct, but the numerical value inherits the error from Step 1.
- Step 3Correct
Your final conversion from millimoles of iron to milligrams using is executed properly, but it carries forward the incorrect mole count.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly recognized that corresponds to for dilute aqueous solutions.
You properly applied the stoichiometric mole ratio between iron and lead(II) ions.
You successfully tracked your units using and consistently throughout the problem.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou used the atomic mass of lead () instead of the molar mass of lead(II) nitrate ().
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the mass concentration of an entire dissolved salt compound with the mass concentration of its constituent heavy metal cation.
REASONING PATH
Your ACEpath teacher’s suggested approach- Identify the chemical identity of the ppm specification
When a problem specifies ' of compound ', the mass numerator represents mass of compound , not just one ion inside it.
Always check the solute formula given next to the concentration value and use the molar mass of that complete formula.
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate the molarity of : . Because each formula unit gives one , .
Determine total moles of in : .
Use the mole ratio to find iron required: .
Compute the mass of iron: .
(a) ; (b)
03 The student incorrectly assumes a 2:1 stoichiometry between iron and lead(II) ions, doubling the required moles of iron.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
(or )
According to the balanced net ionic equation , one mole of iron reacts with one mole of lead(II) ions. Multiplying by incorrectly doubles the required moles of iron.
- Step 4Correct
Your multiplication by the atomic mass of iron was executed correctly, but the result is doubled due to the stoichiometric error in the previous step.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly equated to for dilute aqueous solutions.
You correctly converted the solute mass concentration to molar concentration using the formula mass of .
You accurately computed the total millimoles of present in the effluent volume.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou introduced a coefficient of when relating moles of iron to moles of lead(II), likely confusing the charge or the two nitrate counter-ions with the redox reaction's mole ratio. In the single-replacement reaction , both metals transfer electrons per atom, making the stoichiometric ratio strictly .
REASONING PATH
Your ACEpath teacher’s suggested approach- Inspect Balanced Reaction Coefficients
In redox and single-replacement stoichiometry, always inspect the balanced net equation: .
Write down , verify that both coefficients are , and set .
CORRECTED PATH
ACEpath Teacher's DemonstrationFrom the balanced equation , the mole ratio is , so .
Calculate the mass of solid iron consumed: .
(a) ; (b)
Lock it in
What is the relationship between molar concentration (), volume (), and total moles ()?
. Molarity is an intensive property (per unit volume), whereas moles represent the total extensive quantity in that specific volume.
Similar question
A wastewater stream contains of cadmium ions, . A water treatment plant treats a batch of this wastewater with solid zinc turnings via . Calculate: (a) the total moles of in the batch in , and (b) the mass of zinc consumed in milligrams (molar mass of ).
Answer
(a) Total moles of .\n(b) Using the stoichiometric ratio, . Mass of (or to 2 sig figs).
An industrial rinsing tank holds of an aqueous solution containing of copper(II) sulfate, (, where ). Granular iron is used to precipitate copper via . Determine: (a) the molarity of in , and (b) the minimum mass of iron in milligrams required to treat the entire tank (molar mass of ).
Answer
(a) Mass concentration = . .\n(b) Total moles of . By stoichiometry, . Mass of .
A hydrometallurgical processing tank contains of a silver effluent with of silver nitrate, (). Copper metal is added to displace silver according to the single-replacement reaction: . Calculate: (a) the concentration of in , (b) the total moles of in the tank in , and (c) the mass of solid copper consumed in milligrams (molar mass of ).
Answer
(a) Concentration of . .\n(b) Total moles of .\n(c) From stoichiometry, . Mass of .