Resources
In a municipal water treatment facility, trace sulfate ions are removed by precipitating insoluble barium sulfate: . A industrial wastewater sample has a sodium sulfate concentration of . Calculate the amount of sodium sulfate present in millimoles (), and determine the mass of solid barium chloride () in milligrams () required to completely precipitate all sulfate ions from this wastewater sample. (Molar masses: , ).
Answer and steps
Final answer
;
Steps
Calculate the mass of sodium sulfate () in the sample
Convert the volume of the wastewater sample from milliliters to liters:
Using the given concentration, calculate the mass of present:
Determine the molar amount of in millimoles ()
The molar mass of is , which is equivalent to :
Use reaction stoichiometry to find the required amount of barium chloride ()
From the balanced chemical equation:
The stoichiometric ratio between and is . Therefore, the amount of needed to react completely with all sulfate ions is:
Calculate the required mass of in milligrams ()
The molar mass of is (or ). Calculate the mass:
Typical errors
01 The student forgets to convert the sample volume from milliliters to liters, multiplying concentration directly by 500.0 and overestimating the amount by a factor of 1000.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You multiplied the concentration in directly by without converting milliliters to liters. Since , the mass is .
- Step 2Correct
You correctly used the formula , but this step inherits the inflated mass value from Step 1.
- Step 3Correct
You correctly identified the stoichiometric ratio from the balanced equation, but the mole quantity carried over the previous scale error.
- Step 4Correct
You correctly multiplied moles by molar mass to find mass, but the result is times too large due to the uncoverted volume in Step 1.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified the molar ratio between and from the chemical equation.
You correctly used molar masses expressed as to convert between mass and amount in millimoles.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou substituted the volume directly as instead of converting to .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisOverlooking dimensional consistency between the concentration unit denominator () and the given volume unit ().
REASONING PATH
Your ACEpath teacher’s suggested approach- Check Unit Compatibility
When multiplying a concentration by a volume, their volume units must cancel: .
Always write out the units explicitly in the calculation and convert to by dividing by before multiplying.
CORRECTED PATH
ACEpath Teacher's DemonstrationConvert volume: .
Calculate mass: .
Calculate moles: .
Use stoichiometry: .
Calculate final mass: .
;
02 The student misinterprets the 1:2 stoichiometric coefficient ratio in front of NaCl as applying between BaCl2 and Na2SO4, halving the required amount of BaCl2.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
In the balanced reaction , the stoichiometric coefficients of and are both . The mole ratio between the two reactants is , so should equal rather than being divided by .
- Step 4Correct
Your multiplication by the molar mass was algebraically sound, but the final mass is halved because of the stoichiometric error in Step 3.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly converted the wastewater volume from milliliters to liters.
You calculated the dissolved mass of sodium sulfate accurately.
You converted mass to millimoles using the correct molar mass.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou took the coefficient of belonging to the product (or the two ions in the formula) and applied it as a mole ratio between the two reactants, overlooking that and react in an equimolar ratio.
REASONING PATH
Your ACEpath teacher’s suggested approach- Identify Reactant Coefficients
Only the stoichiometric coefficients of the two substances being compared determine their mole ratio: .
Box the coefficients of the specific known and unknown species directly in the balanced equation before setting up the ratio.
CORRECTED PATH
ACEpath Teacher's DemonstrationFrom the balanced equation, the mole ratio of to is : .
Calculate the required mass of : .
;
03 The student divides by the molar mass of BaCl2 instead of multiplying when converting millimoles to milligrams.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3
- Step 4Correct
To convert from an amount in millimoles to mass in milligrams, you must multiply by the molar mass (), not divide. Dividing millimoles by yields instead of milligrams.
WHAT YOU DID WELL
Compliments from Your TeacherYou converted the volume to liters accurately.
You correctly calculated the mass of dissolved sodium sulfate.
You correctly calculated the millimoles of and applied the mole ratio to find .
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou inverted the relationship between mass, chemical amount, and molar mass by dividing moles by molar mass () rather than multiplying ().
REASONING PATH
Your ACEpath teacher’s suggested approach- Dimensional Analysis Check
Always write out and cancel the units: .
CORRECTED PATH
ACEpath Teacher's Demonstration;
Lock it in
When a solute concentration is given in and sample volume is given in , how must you convert the volume before multiplying?
Divide the volume by to convert to , ensuring volume units cancel: .
Similar question
A sample of river water has a chloride concentration of . Calculate the amount of chloride ions present in millimoles (). (Molar mass of )
Answer
. Steps: 1) Convert volume: . 2) Calculate mass: . 3) Convert to moles: .
A solution contains lead(II) ions at a concentration of . What mass of sodium iodide (, ) in milligrams is needed to precipitate all lead as according to ? (Molar mass of )
Answer
. Steps: 1) Mass of . 2) Moles of . 3) Moles of . 4) Mass of .
A contaminated water stream contains of calcium ions (, ). If a treatment basin treats of this water by adding to precipitate , what volume of the sodium carbonate solution in milliliters is required?
Answer
. Steps: 1) Mass of . 2) Moles of . 3) By reaction with , . 4) Volume .