Resources
Ethylene oxide (, molar mass ) is manufactured industrially via partial catalytic oxidation of ethylene: (). However, complete combustion simultaneously occurs as a competing side reaction: (). In a fixed-bed reactor fed with of ethylene, the overall ethylene conversion is , with a selectivity of toward ethylene oxide (the remaining reacted ethylene undergoes complete combustion). Calculate: (a) the production rate of ethylene oxide in , and (b) the total rate of heat generation (in megawatts, ) that the coolant system must continuously remove from the reactor to maintain isothermal operation.
Answer and steps
Final answer
(a) ; (b) .
Steps
Determine the moles of ethylene consumed in each pathway
The total feed rate of ethylene () to the reactor is:
With a single-pass conversion of , the total consumption rate of ethylene is:
Out of the reacted ethylene, is converted selectively into ethylene oxide ( via Reaction 1), while the remaining is fully combusted into and (via Reaction 2):
- Ethylene consumed via partial oxidation (Reaction 1):
- Ethylene consumed via complete combustion (Reaction 2):
Calculate the production rate of ethylene oxide
From the stoichiometry of Reaction 1:
Each mole of ethylene reacted produces one mole of ethylene oxide. Therefore:
Using the molar mass of ethylene oxide () and converting seconds to hours ():
Calculate the total rate of heat generation (Cooling Heat Duty)
Both reactions are exothermic and release heat at steady state:
- Heat release rate from partial oxidation ():
- Heat release rate from complete combustion ():
Notice that even though only of the reacted ethylene undergoes combustion, its high enthalpy of reaction accounts for the majority of the heat load.
The total heat generation rate that the cooling system must remove to maintain an isothermal state is:
Typical errors
01 The student calculates selectivity based on the total ethylene feed rather than the reacted ethylene, overestimating product flow and heat release.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
Selectivity is defined based on the moles of reactant consumed, not the total moles fed. Because only of the ethylene reacts, the reacted ethylene is , making the rate of partial oxidation .
- Step 2Correct
Your unit conversion steps and molar mass multiplication were set up correctly, but the result is carried over from the incorrect ethylene consumption rate in Step 1.
- Step 3Correct
When your calculation gave , that was a direct signal that the exceeded the total reacted ethylene (). Instead of applying to the feed, the remaining reacted ethylene is .
- Step 4Correct
Your method of multiplying individual reaction rates by reaction enthalpies and summing them to find the total cooling duty in megawatts was executed properly, but the numerical value inherits the errors from Steps 1 and 3.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly used the molar mass of ethylene oxide () along with appropriate conversion factors to convert molar flow to mass flow rate in .
You correctly multiplied each reaction rate by its respective standard enthalpy of reaction to compute the total heat generation.
You converted to megawatts () with the correct scale factor ().
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakenone
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou defined selectivity based on the total inlet feed rate instead of the amount of reactant actually consumed by reactions. Selectivity partitions only the reacted portion of the feed ().
REASONING PATH
Your ACEpath teacher’s suggested approach- Conversion vs. Selectivity Hierarchy
Conversion () determines how much total reactant reacts: . Selectivity () splits that reacted amount among competing paths: .
Always compute the total reacted molar flow first before multiplying by any selectivity fraction.
- Sanity Check for Reacted Quantities
The sum of reactant consumed in all parallel pathways cannot exceed the total reacted reactant: .
If your pathway balance produces a negative molar flow (such as ), stop and verify whether you accidentally used the gross feed instead of the reacted flow.
CORRECTED PATH
ACEpath Teacher's DemonstrationCompute the total reacted ethylene: .
Apply selectivity to find the partial oxidation flow: .
Calculate ethylene oxide mass flow: .
Find combustion flow: .
Calculate total heat duty: .
(a) ; (b)
02 The student forgets to account for the heat generated by the complete combustion side reaction, considering only the main reaction.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
You only accounted for the heat released by partial oxidation. You also need to include the heat from the remaining of reacted ethylene () that undergoes complete combustion ().
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly used the conversion fraction to determine the total molar rate of ethylene reacted.
You accurately applied selectivity and molar mass units to find the ethylene oxide production rate in kilograms per hour.
You correctly set up the heat generation equation for the desired partial oxidation reaction.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou focused exclusively on the main product pathway when performing the reactor energy balance, forgetting that unselective parallel reactions (especially highly exothermic complete combustions) contribute significantly to the total heat duty.
REASONING PATH
Your ACEpath teacher’s suggested approach- Account for all reacting pathways in energy balances
Total steady-state heat generation equals the sum of heats of reaction across all occurring pathways: .
Always find the extent or consumption rate of each competing side reaction and add its enthalpy release to the cooling duty.
CORRECTED PATH
ACEpath Teacher's DemonstrationDetermine the molar consumption rate of ethylene via complete combustion: .
Calculate the heat generation rate from complete combustion: .
Sum the heat generated by both reactions: .
(a) ; (b)
03 The student multiplies by 60 instead of 3600 when converting seconds to hours for the production rate.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You multiplied by instead of . Because there are in (), multiplying by gives the mass flow per minute rather than per hour.
- Step 3
- Step 4
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the consumption rate of ethylene through both partial oxidation and complete combustion.
You correctly used the molar mass to determine the mass rate of ethylene oxide in kilograms per second.
You accurately combined the reaction enthalpies to obtain the total heat removal rate in megawatts.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou converted from seconds to minutes by multiplying by , but labeled and treated the resulting value as an hourly rate.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisOverlooking the two-step unit chain between seconds and hours () when converting time in the denominator of a rate.
REASONING PATH
Your ACEpath teacher’s suggested approach- Time unit conversion chain
To convert a rate per second into a rate per hour: .
Write out the conversion factors explicitly with cancelling units: .
CORRECTED PATH
ACEpath Teacher's Demonstration(a) ; (b)
Lock it in
In chemical reaction engineering, what is the key difference between conversion () and selectivity ()?
Conversion is the fraction of total feed that reacts (). Selectivity is the fraction of reacted material converted to the desired product ().
Similar question
Propylene () enters an acrolein reactor with conversion and selectivity to acrolein (molar mass ). Calculate the mass production rate of acrolein in .
Answer
. Reacted propylene = . Acrolein formed = . Mass rate = .
Methanol is oxidized to formaldehyde: (1) () and (2) (). For a feed of methanol with conversion and selectivity to , find the cooling duty required (in ) to maintain isothermal conditions.
Answer
. Reacted methanol = . Moles to reaction 1 = . Moles to reaction 2 = . Heat duty .
Benzene () is chlorinated. Reaction 1 forms monochlorobenzene (MCB, ), and Reaction 2 forms dichlorobenzene (DCB, consuming 1 mol benzene, ). Benzene conversion is . If the reactor cooling system can remove at most , what is the minimum selectivity toward MCB required to prevent overheating?
Answer
. Total reacted benzene = . Let be selectivity to MCB. Heat released: . Then or .