Resources
An environmental water quality sample contains dissolved lead() ions at a trace concentration of (parts per billion, where ). Assuming the aqueous solution has a standard density of , calculate the concentration of lead() ions in the derived SI unit of kilograms per cubic meter (). Express your result in standard scientific notation with three significant figures.
Answer and steps
Final answer
Steps
Interpret the given concentration in fundamental units
The problem defines parts per billion () on a mass-by-mass basis:
Since , a concentration of can be expressed directly as:
Convert the solution density into SI derived units ()
The density of the aqueous solution is given as . Convert this to kilograms per cubic meter ():
Thus, each cubic meter of solution has a mass of .
Calculate the concentration in using dimensional analysis
Multiply the mass fraction of ions by the solution's density to find the mass of solute per unit volume of solution:
Express in standard scientific notation with correct significant figures
In standard scientific notation, a number is written as , where .
Both the given concentration () and the solution density () have at least three significant figures, so the result is rounded to three significant figures: .
Common Pitfall: Do not confuse parts per million ( or ) with parts per billion ( or ). Additionally, when converting to , remember that volume scales cubically, meaning , not or .
Typical errors
01 The student misinterprets parts per billion as parts per million, equating 1 ppb to 1 mg/kg (10⁻⁶) instead of 1 μg/kg (10⁻⁹), leading to an answer that is three orders of magnitude too large.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You defined as , which corresponds to parts per million (ppm). Parts per billion is defined as , which equals .
- Step 2
- Step 3Correct
Your division and scientific notation formatting followed your intermediate values correctly, but the result inherited the factor error from Step 1.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly converted the density of water from to SI units of .
You set up a sound dimensional analysis structure by dividing solute mass by solution volume.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou confused the prefix conventions for fractional concentrations: parts per million (ppm) corresponds to (or ), whereas parts per billion (ppb) corresponds to (or ).
REASONING PATH
Your ACEpath teacher’s suggested approach- Recall the definition of ppb
Check whether the problem specifies parts per million () or parts per billion () before writing down unit equivalents.
- Verify metric prefix magnitudes
, whereas
Translate prefixes to scientific powers of 10 explicitly before substituting into a density or concentration formula.
CORRECTED PATH
ACEpath Teacher's DemonstrationExpress using its correct unit definition: .
Divide by the volume of of solution (): .
Format the result in standard scientific notation with three significant figures: .
02 The student incorrectly converts density from g/cm³ to kg/m³ by dividing by 1000 instead of multiplying by 1000, setting 1.000 g/cm³ equal to 0.001 kg/m³.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You divided by instead of accounting for the cubic conversion factor between and . Since , , making equal to .
- Step 3Correct
Your formula was set up correctly, but substituting the incorrect density value yielded an unphysically large volume.
- Step 4Correct
Your final calculation followed logically from your prior steps, but it carries the factor-of- error introduced in Step 2.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly related parts per billion to micrograms of solute per kilogram of solution.
You converted micrograms to kilograms accurately in standard scientific notation.
You applied the correct relationship between mass, volume, and density.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated the conversion factor between and as just the mass conversion (), omitting the cubic volume conversion factor ().
REASONING PATH
Your ACEpath teacher’s suggested approach- Convert derived units step-by-step
For composite units with powers, raise the entire linear conversion factor to that power: .
Set up separate conversion factors for numerator and denominator rather than guessing a single multiplier.
- Perform a physical reality check
One cubic meter of water () weighs approximately (one metric ton), not .
Check whether your converted density value represents water being extremely light or correctly dense.
CORRECTED PATH
ACEpath Teacher's DemonstrationConvert density using dimensional analysis: .
Find the volume of of solution: .
Calculate concentration: .
03 The student assumes 1.000 g/cm³ corresponds directly to 1 kg/m³ without converting the cubic centimeters in the denominator to cubic meters, omitting the factor of 10³ for solution volume.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
When converting density to SI derived units, both mass and volume must be converted. While , , so , not .
- Step 3Correct
This step correctly applied the relation , but it used the incorrect density value from Step 2.
- Step 4Correct
The calculation followed your previous numbers correctly, but the resulting concentration is off by a factor of due to the earlier density conversion error.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly interpreted the definition of parts per billion as micrograms of solute per kilogram of solution.
You correctly converted micrograms to kilograms using the factor .
You set up a sound dimensional pathway dividing solute mass by solution volume.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated the ratio as if the prefixes cancel out directly to , overlooking that cubic centimeters scale by when converting to cubic meters.
REASONING PATH
Your ACEpath teacher’s suggested approach- Cubic Unit Conversions
When converting derived volume units, cube the linear conversion factor: .
Always set up conversion factors with explicit powers on the unit brackets, such as .
- Water Density Benchmark
Pure water at standard conditions has a density of .
Use as a quick mental benchmark: a cubic meter of water weighs one metric ton (), not .
CORRECTED PATH
ACEpath Teacher's DemonstrationLock it in
What mass-based unit ratio defines 1 part per billion (ppb) in an aqueous solution?
. One billion is , so the fraction is .
Similar question
A drinking water sample contains of arsenic. If the water density is , calculate the concentration of arsenic in in standard scientific notation.
Answer
. First, convert concentration to mass fraction: . Next, convert density: . Finally, multiply mass fraction by density: .
An industrial wastewater stream contains of cadmium. Assuming a solution density of , determine the concentration in in scientific notation with three significant figures.
Answer
. Convert ppm to mass fraction: . Convert density: . Multiply to obtain volumetric concentration: .
An ocean surface sample has a mercury concentration of . Given that seawater has a density of , find the total mass of mercury (in milligrams) present in a seawater storage tank.
Answer
. First, find the total mass of seawater: . Then, calculate mercury mass using : .