Resources
A common industrial misconception holds that operating a reversible exothermic reaction at maximum permissible temperature always optimizes reactor productivity. Consider the gas-phase catalytic oxidation of sulfur dioxide in the Contact Process: (). (a) Apply Le Chatelier's principle and thermodynamic equilibrium expressions to explain why raising the operating temperature from to causes the equilibrium conversion of to drop markedly from to . (b) An industrial converter with a feed of , , and at reaches equilibrium at ( conversion). Calculate the total enthalpy released per mole of total initial feed mixture and explain why multi-bed adiabatic converters utilize interstage heat exchangers rather than a single high-temperature isothermal bed.
Answer and steps
Final answer
(a) Since , heat acts as a product; increasing temperature shifts equilibrium toward reactants ( decreases from at to at ); (b) per mole of initial feed; interstage cooling shifts equilibrium forward at lower downstream temperatures while maintaining rapid initial kinetic rates in the first high-temperature stage.
Steps
Enthalpy Released per Mole of Total Initial Feed
Part (a): Thermodynamic and Le Chatelier Analysis
- Le Chatelier's Principle:
The reaction is strongly exothermic: Thermal energy (heat) acts conceptually as a product: Raising the temperature from () to () supplies heat to the system. According to Le Chatelier's principle, the system counteracts this stress by shifting in the endothermic reverse direction, consuming heat and decomposing back into and . Consequently, the equilibrium conversion drops significantly from to . - Thermodynamic Relationship (van 't Hoff Equation):
The temperature dependence of the equilibrium constant is governed by the van 't Hoff equation: Because , , meaning decreases monotonically as temperature increases. Quantitatively:- At ,
- At , The steep drop in thermodynamically limits the maximum achievable conversion at elevated temperatures.
Part (b): Enthalpy Calculation and Reactor Configuration
- Basis: of initial feed gas.
- Initial amount of :
- Amount of reacted at conversion:
- Molar enthalpy change per mole of reacted:
The balanced equation releases per of consumed: - Enthalpy released per mole of feed:
Rationale for Multi-Bed Adiabatic Converters with Interstage Cooling
- Kinetic vs. Thermodynamic Trade-off:
- At high temperatures (), reaction kinetics are rapid, allowing fast initial conversion, but the equilibrium conversion ceiling is low ().
- At low temperatures (), the thermodynamic equilibrium conversion is very high (), but reaction rates are too sluggish to be practical on an industrial scale.
- Role of Interstage Heat Exchangers:
In a multi-bed catalytic converter, the gas enters the first catalyst bed at a higher temperature to achieve rapid initial reaction rates. As the exothermic reaction proceeds, the gas temperature increases adiabatically. Before entering the subsequent bed, the gas passes through an interstage heat exchanger (cooler). Lowering the temperature resets the thermodynamic driving force and shifts the equilibrium forward according to Le Chatelier's principle. This alternating cycle of reaction and cooling enables industrial Contact Process plants to exceed overall conversion, which is impossible in a single isothermal bed operating at elevated temperatures.
Typical errors
01 The student forgets that ΔH°_rxn corresponds to 2 moles of SO2 and multiplies the reacted moles directly by 198 kJ/mol instead of 99 kJ/mol.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
The forward reaction is exothermic, so heat is released as a product. Increasing temperature shifts the equilibrium in the reverse endothermic direction by Le Chatelier's principle. From van 't Hoff equation, , so decreases and conversion drops from to .
- Step 2
- Step 3Correct
In the balanced reaction , represents the enthalpy change per mole of the reaction as written, which consumes . Therefore, the heat released per mole of reacted is . Multiplying directly by overestimated the heat release by a factor of 2.
- Step 4
Interstage cooling lowers temperature downstream to overcome thermodynamic equilibrium limitations while retaining fast kinetics in early beds.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly applied Le Chatelier's principle and the van 't Hoff equation to justify the conversion drop.
You correctly determined the moles of reacted using a feed basis.
You accurately explained why industrial converters use interstage cooling to balance kinetics and equilibrium conversion.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated the reaction enthalpy as being per mole of rather than per stoichiometric equivalent of the balanced chemical equation ().
REASONING PATH
Your ACEpath teacher’s suggested approach- Standard Enthalpy of Reaction per Moles Reacted
, where is the stoichiometric coefficient of reactant .
Always divide the moles of reactant consumed by its stoichiometric coefficient in the balanced equation before multiplying by .
CORRECTED PATH
ACEpath Teacher's DemonstrationIdentify the stoichiometric coefficient of in the balanced equation: .
Calculate the reaction extent: .
Multiply extent by enthalpy: .
(a) makes heat a product; increasing temperature shifts equilibrium toward reactants by Le Chatelier's principle (quantified by ). (b) per mole of initial feed; interstage cooling shifts equilibrium forward at lower downstream temperatures while maintaining rapid initial kinetic rates in the first high-temperature stage.
02 The student calculates the enthalpy released per mole of SO2 feed rather than per mole of total initial feed mixture.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
Since is negative, the reaction is exothermic. By Le Chatelier's principle, added heat favors the reverse endothermic reaction. The van 't Hoff relation shows decreases as increases, reducing the equilibrium conversion.
- Step 2
Basis: of feed. Moles of reacted
CorrectBasis: of total initial feed mixture. , so
You chose of pure as your basis. The problem specifies calculating the enthalpy released per mole of the total initial feed mixture, which contains ( per mole of feed).
- Step 3
Heat released Enthalpy released
Correctper mole of total initial feed
Your stoichiometric factor of was correct, but your numerical answer was ten times too large because it propagated the incorrect basis from Step 2.
- Step 4
Cooling between beds shifts the equilibrium toward products at lower temperatures while maintaining high initial rates at high temperatures.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly applied Le Chatelier's principle and the van 't Hoff equation to explain why equilibrium conversion declines with temperature.
You used the correct stoichiometric ratio between consumed and the reaction enthalpy.
You clearly articulated the kinetic-thermodynamic compromise that justifies multi-bed reactor design with interstage cooling.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou selected pure as the calculation basis rather than the total feed mixture.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisOverlooking inert and secondary feed fractions when converting from an overall gas feed composition to the moles of limiting reactant reacting per mole of mixture.
REASONING PATH
Your ACEpath teacher’s suggested approach- Establish the exact reference basis
When a problem asks for an extensive quantity 'per mole of total initial feed', the basis must be of mixture, not of a specific reacting component.
Always write down the mole fractions of all feed components (, , ) before calculating the moles of reactant.
CORRECTED PATH
ACEpath Teacher's DemonstrationChoose a basis of of total initial feed mixture.
Calculate initial : .
Calculate reacted : .
Multiply by molar heat release per : .
per mole of initial feed mixture
03 The student reverses the temperature dependence of equilibrium for exothermic reactions, claiming higher temperature increases K_p.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
The reaction is exothermic with
CorrectSince , heat is released by the forward reaction. By Le Chatelier's principle, adding thermal energy shifts the equilibrium in the endothermic reverse direction. Thermodynamically, the van 't Hoff equation shows that decreases as temperature increases, reducing the equilibrium conversion ceiling.
You confused reaction rates (kinetics) with the equilibrium constant (thermodynamics). While higher temperatures increase collision frequency and both forward and reverse rate constants ( and ), the equilibrium constant decreases for an exothermic reaction because the reverse endothermic activation barrier causes to increase more steeply than .
- Step 2
1.00 n_{2} = 0.100 n{} = 0.100 0.580 = 0.0580 q_{} = 0.0580 99.0 = 5.74
- Step 3
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified that the oxidation of is exothermic with .
You calculated the exact molar enthalpy released per mole of feed gas () using sound stoichiometric reasoning.
You recognized that elevated temperatures thermodynamically restrict conversion in the later stages of an industrial converter.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou stated that increasing temperature increases instead of decreasing it for an exothermic reaction.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou conflated kinetic activation concepts (temperature increases collision frequency and rate constants) with thermodynamic equilibrium ( and equilibrium position). For an exothermic reaction, heat acts as a product, so raising temperature thermodynamically disfavors the products and decreases .
REASONING PATH
Your ACEpath teacher’s suggested approach- Temperature Dependence of $K_p$
For an exothermic reaction (), the van 't Hoff equation dictates that decreases as temperature rises.
Check the sign of . If negative, treat heat as a product: increasing temperature always reduces .
- Kinetics vs. Thermodynamics
Equilibrium conversion depends solely on and thermodynamics, not on collision rates or kinetic speeds.
Explain conversion limits using equilibrium constants and Le Chatelier's principle, keeping rate constants () and activation energies separate from .
CORRECTED PATH
ACEpath Teacher's DemonstrationIdentify the reaction as exothermic: .
Apply the van 't Hoff relationship: , which proves that decreases from at to at .
Apply Le Chatelier's principle: heating shifts the reaction in the endothermic direction (reverse), causing the equilibrium conversion to fall from to .
(a) Because , increasing temperature shifts equilibrium toward reactants, decreasing ; (b) per mole of initial feed; interstage cooling restores favorable equilibrium conditions downstream while preserving fast kinetics upstream.
Lock it in
What does the unit 'kJ/mol' in a standard enthalpy of reaction specifically refer to?
It refers to per mole of reaction formula unit as written, not necessarily per mole of each individual reactant or product.
Similar question
In the Haber-Bosch synthesis, has . If an industrial reactor feed contains and , and achieves conversion of , calculate the total heat released per mole of feed gas.
Answer
. Basis: . reacted . Since , extent . Heat released .
The oxidation of ammonia proceeds via with . A reactor combusts with stoichiometric to completion. Calculate the enthalpy change of the process and state the heat released per mole of .
Answer
; heat released is . Extent . Total . Heat per mole of .
In a methanol synthesis converter, has . A feed stream of with composition , , and (inert) achieves equilibrium conversion of . Calculate the rate of heat removal (in ) required to maintain isothermal operation.
Answer
Rate of heat removal . Feed flow rate . Moles of reacted per second . Since , rate of reaction extent . Heat generated .