Resources
An unidentified monovalent metallic element crystallizes in a body-centered cubic (BCC) lattice with a measured electrical conductivity of at . According to the Drude model of electrical conduction, conductivity is given by , where and . If the measured mean relaxation time between electron-lattice scattering events is , calculate the conduction electron density (in electrons per cubic meter, ).
Answer and steps
Final answer
Steps
Rearrange for the electron density
To find the conduction electron density , we use the classical Drude model formula for electrical conductivity:
Isolating the number density of free electrons :
Substitute the given values
The problem provides the following parameters in standard SI units:
- Measured electrical conductivity:
- Electron mass:
- Elementary charge:
- Relaxation time:
Substitute these values into the rearranged equation:
Compute the numerator and denominator
- Numerator:
- Denominator:
- Divide:
Common Pitfall
Ensure all quantities are kept strictly in SI units. Since an ohm () is and , the units directly cancel to yield , representing the number of free conduction electrons per unit volume.
Typical errors
01 The student forgets to square the elementary charge e in the denominator of the rearranged Drude expression, resulting in an electron density that is ten orders of magnitude too small.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
When dividing both sides by , you omitted the square on the elementary charge , writing instead of in the denominator.
- Step 3Correct
You substituted the correct numerical values and evaluated the arithmetic accurately based on your rearranged formula, but the denominator was missing the factor of .
- Step 4Correct
Because was not squared in the denominator, your final density is roughly 19 orders of magnitude lower than typical metallic electron densities.
WHAT YOU DID WELL
Compliments from Your TeacherYou selected the correct theoretical equation from the Drude model.
You substituted all given physical constants and parameters in consistent SI units.
You performed the multi-step scientific notation arithmetic carefully.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou dropped the exponent on when isolating from the product .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisInattention during symbolic variable isolation led to copying as a linear term into the denominator, which drastically altered the order of magnitude of the denominator.
REASONING PATH
Your ACEpath teacher’s suggested approach- Symbolic Auditing
When solving for , divide by the entire factor .
Always circle or highlight powers before rearranging algebraic fractions to verify no exponents disappear.
- Order-of-Magnitude Sanity Check
Conduction electron densities in solid metals are typically on the order of .
If your calculated electron density for a metal is near (which is less dense than air molecules), stop and check for missing powers of fundamental constants like or .
CORRECTED PATH
ACEpath Teacher's DemonstrationRearrange to obtain .
Square the elementary charge: .
Compute the denominator: .
Divide numerator by denominator: .
02 The student incorrectly inverts the algebraic rearrangement of the formula, writing n = (e² · τ) / (σ · m_e) instead of multiplying by m_e and dividing by e²·τ.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
To isolate , you need to multiply both sides by and divide both sides by . You accidentally inverted the relationship, placing and in the denominator instead of the numerator.
- Step 3Correct
Your arithmetic evaluation of the individual products was carried out accurately, but it evaluated the inverted expression from Step 2.
- Step 4Correct
Because of the inverted formula at Step 2, your final answer is approximately rather than .
WHAT YOU DID WELL
Compliments from Your TeacherYou selected the correct physical formula for the Drude model of conductivity.
You correctly identified and substituted all numerical constants and given values with their proper SI units.
You accurately computed the powers of ten and decimal products in your arithmetic.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated the isolation of a variable in the numerator of a fraction by dividing by the original left-hand side rather than multiplying by the denominator and dividing by the remaining numerator factors.
REASONING PATH
Your ACEpath teacher’s suggested approach- Isolating a Numerator Factor
For an equation of the form , multiplying both sides by gives , and dividing by gives .
Always multiply by the denominator first to clear fractions before dividing by the factors multiplying your target variable.
- Physical Reality Check on Number Density
Conduction electron densities in solid metals typically range around to .
Check whether your result has an impossible magnitude; an exponent of implies less than one electron per universe-sized volume, signalling an inverted fraction.
CORRECTED PATH
ACEpath Teacher's DemonstrationMultiply both sides of by : .
Divide both sides by to isolate : .
Substitute the given values: .
Compute numerator and denominator: .
03 The student enters the denominator into a calculator without grouping parentheses, effectively multiplying by τ rather than dividing by it.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
You factored out as a multiplier instead of keeping it in the denominator as a divisor. Dividing by requires dividing by both and , or grouping them together: .
- Step 4Correct
Your final numerical answer is incorrect due to multiplying by rather than dividing by it in the previous step.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified and rearranged the Drude model equation to solve for .
You substituted all the correct physical constants and parameters in consistent SI units.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou accidentally multiplied by the relaxation time instead of keeping it in the denominator when calculating.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisMisinterpreting the fraction during calculation as instead of . In a calculator, entering A / B * C evaluates as (A / B) * C unless the entire denominator is enclosed in parentheses.
REASONING PATH
Your ACEpath teacher’s suggested approach- Denominator Parentheses Rule
For any expression of the form , both factors belong in the denominator: .
Always place parentheses around multi-factor denominators when computing, or evaluate the entire denominator as a single product before dividing.
- Physical Reasonableness Check
Conduction electron densities in typical solid metals are on the order of .
Check your final exponent: an electron density of means only free electrons per cubic meter, which is unphysically low for a conducting solid.
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate the numerator: .
Calculate the full denominator: .
Divide the numerator by the full denominator: .
Lock it in
In the Drude model of electrical conductivity , why does the elementary charge appear as ?
One factor of comes from the electric force driving acceleration (), and the second comes from the current density definition (). Always ensure is squared when rearranging!
Similar question
A divalent metal has an electrical conductivity of and an electron density of . Using the Drude formula with and , calculate its relaxation time .
Answer
. Key steps: Rearrange to . Compute numerator . Compute denominator . Dividing yields .
Copper has a relaxation time of and electrical conductivity . If each copper atom contributes exactly one conduction electron, calculate the conduction electron density using the Drude model.
Answer
. Key steps: .
An unknown monovalent alkali metal crystallizes in a BCC unit cell with lattice parameter (). First, find the theoretical conduction electron density from the crystal geometry (recall a BCC unit cell contains 2 atoms). Then, if its measured conductivity is , determine its relaxation time .
Answer
and . Key steps: 1) Unit cell volume . With 2 electrons per BCC cell, . 2) From Drude model, .