Resources

A decorative copper figurine is to be electroplated with gold from an aqueous gold(III) cyanide bath containing Au3+(aq)\text{Au}^{3+}(aq) ions via the cathode half-reaction Au3+(aq)+3e−→Au(s)\text{Au}^{3+}(aq) + 3e^- \rightarrow \text{Au}(s). To provide adequate corrosion resistance, a coating specifications sheet dictates that exactly 3.54 g3.54\text{ g} of metallic gold must be deposited uniformly onto the figurine over a fixed process window of 45.0 minutes45.0\text{ minutes}. Assuming an operating cathode current efficiency of 92.0%92.0\%, calculate the constant electric current II (in amperes, A\text{A}) that the DC power supply must deliver. (Data: F=96485 C/molF = 96485\text{ C/mol}; molar mass of gold M=196.97 g/molM = 196.97\text{ g/mol})

Answer and steps

Final answer

I=2.09 AI = 2.09\text{ A}

Steps

01

Calculate the moles of gold (Au\ce{Au}) deposited

To find the required electric current, we apply Faraday's laws of electrolysis, relating the mass of substance deposited to electric charge, and then account for the current efficiency.

Using the mass of gold (m=3.54 gm = 3.54\text{ g}) and its molar mass (M=196.97 g/molM = 196.97\text{ g/mol}): nAu=mM=3.54 g196.97 g/mol≈0.017972 moln_{\ce{Au}} = \frac{m}{M} = \frac{3.54\text{ g}}{196.97\text{ g/mol}} \approx 0.017972\text{ mol}

02

Determine the theoretical charge (QtheoreticalQ_{\text{theoretical}}) needed

The cathode half-reaction is: AuX3+(aq)+3 eX−→Au(s)\ce{Au^{3+}(aq) + 3e^- -> Au(s)}

Each mole of Au\ce{Au} deposited requires z=3 moles of electronsz = 3\text{ moles of electrons}. The theoretical amount of electric charge (QtheoreticalQ_{\text{theoretical}}) is: Qtheoretical=nAu⋅z⋅FQ_{\text{theoretical}} = n_{\ce{Au}} \cdot z \cdot F Qtheoretical=0.017972 mol⋅3⋅96485 C/mol≈5202.2 CQ_{\text{theoretical}} = 0.017972\text{ mol} \cdot 3 \cdot 96485\text{ C/mol} \approx 5202.2\text{ C}

03

Account for current efficiency to find the total charge (QactualQ_{\text{actual}})

Current efficiency (η\eta) represents the fraction of the total electric current that successfully carries out the desired electroplating reaction: η=QtheoreticalQactual  ⟹  Qactual=Qtheoreticalη\eta = \frac{Q_{\text{theoretical}}}{Q_{\text{actual}}} \implies Q_{\text{actual}} = \frac{Q_{\text{theoretical}}}{\eta}

With η=92.0%=0.920\eta = 92.0\% = 0.920: Qactual=5202.2 C0.920≈5654.5 CQ_{\text{actual}} = \frac{5202.2\text{ C}}{0.920} \approx 5654.5\text{ C}

Common Pitfall: Multiplying by the efficiency rather than dividing. Because side reactions consume part of the current, more total charge must be supplied than the theoretical minimum to deposit the required mass.

04

Convert time to seconds and compute the current (II)

Convert the electroplating duration into SI units (seconds): t=45.0 min⋅60 s/min=2700 st = 45.0\text{ min} \cdot 60\text{ s/min} = 2700\text{ s}

Since constant current is defined as I=QactualtI = \frac{Q_{\text{actual}}}{t}: I=5654.5 C2700 s≈2.094 AI = \frac{5654.5\text{ C}}{2700\text{ s}} \approx 2.094\text{ A}

Rounding to three significant figures gives: I=2.09 AI = 2.09\text{ A}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student multiplies by current efficiency instead of dividing by it, incorrectly concluding that less total current is needed from the power supply.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    n(Au)=3.54 g196.97 g/mol=0.01797 moln(\text{Au}) = \frac{3.54\text{ g}}{196.97\text{ g/mol}} = 0.01797\text{ mol}

  2. Step 2

    t=45.0 min×60 s/min=2700 st = 45.0\text{ min} \times 60\text{ s/min} = 2700\text{ s}

  3. Step 3

    Quseful=0.01797 mol×3×96485 C/mol=5202 CQ_{\text{useful}} = 0.01797\text{ mol} \times 3 \times 96485\text{ C/mol} = 5202\text{ C}

  4. Step 4

    Iuseful=5202 C2700 s=1.927 AI_{\text{useful}} = \frac{5202\text{ C}}{2700\text{ s}} = 1.927\text{ A}

  5. Step 5

    I=1.927 A×0.920=1.77 AI = 1.927\text{ A} \times 0.920 = 1.77\text{ A}

    Correct

    I=Iusefulη=1.927 A0.920≈2.09 AI = \frac{I_{\text{useful}}}{\eta} = \frac{1.927\text{ A}}{0.920} \approx 2.09\text{ A}

    You multiplied by the current efficiency instead of dividing by it. Because only 92.0%92.0\% of the supplied current is used to reduce gold ions (with the rest lost to parasitic reactions), the power supply must deliver more total current than the useful current (Itotal>IusefulI_{\text{total}} > I_{\text{useful}}).

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly determined the moles of gold using the given mass and molar mass.

You converted time into seconds accurately.

You used the correct number of transferred electrons (z=3z = 3) and Faraday's constant to compute the theoretical charge.

You correctly evaluated the theoretical useful current using I=QtI = \frac{Q}{t}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted current efficiency application

Multiplying the theoretical current by current efficiency η\eta instead of dividing by η\eta.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Misinterpreting current efficiency as a reduction factor on required input rather than a ratio of useful output to total input (η=IusefulIactual\eta = \frac{I_{\text{useful}}}{I_{\text{actual}}}). In real electrolysis, side reactions waste current, so the power supply must deliver a higher total current to achieve the desired rate of deposition.

REASONING PATH
Your ACEpath teacher’s suggested approach
Physical Reality Check
  • When current efficiency η<100%\eta < 100\%, the actual input current must always exceed the theoretical useful current (Iactual>IusefulI_{\text{actual}} > I_{\text{useful}}).

  • Check whether your final current is greater than IusefulI_{\text{useful}}. If it is smaller, you multiplied by η\eta when you should have divided.

Efficiency Formula Definition
  • η=useful outputtotal input=IusefulIactual=QtheoreticalQactual\eta = \frac{\text{useful output}}{\text{total input}} = \frac{I_{\text{useful}}}{I_{\text{actual}}} = \frac{Q_{\text{theoretical}}}{Q_{\text{actual}}}.

  • Rearrange for total input before plugging in values: Iactual=IusefulηI_{\text{actual}} = \frac{I_{\text{useful}}}{\eta}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Recall that current efficiency relates useful current to actual supplied current: η=IusefulI  ⟹  I=Iusefulη\eta = \frac{I_{\text{useful}}}{I} \implies I = \frac{I_{\text{useful}}}{\eta}.

  2. Substitute your calculated Iuseful=1.927 AI_{\text{useful}} = 1.927\text{ A} and η=0.920\eta = 0.920: I=1.927 A0.920≈2.094 AI = \frac{1.927\text{ A}}{0.920} \approx 2.094\text{ A}.

  3. Round to three significant figures to match the input data.

Final answer

I=2.09 AI = 2.09\text{ A}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the definition of current efficiency in electrolytic cells: η=IusefulItotal\eta = \frac{I_{\text{useful}}}{I_{\text{total}}}.

  • Perform a quick magnitude sanity check on all efficiency problems: does the cell need more current or less current due to parasitic losses?

  • Complete the targeted flashcards and transfer practice exercises below to master efficiency conversions.

OverviewACEpath Teacher's Diagnosis

02 The student forgets to convert the electroplating duration from minutes to seconds, resulting in a current that is 60 times too large.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    n(Au)=3.54 g196.97 g/mol=0.01797 moln(\text{Au}) = \frac{3.54\text{ g}}{196.97\text{ g/mol}} = 0.01797\text{ mol}

  2. Step 2

    Qtheo=3×0.01797 mol×96485 C/mol=5202 CQ_{\text{theo}} = 3 \times 0.01797\text{ mol} \times 96485\text{ C/mol} = 5202\text{ C}

  3. Step 3

    Qactual=5202 C0.920=5654 CQ_{\text{actual}} = \frac{5202\text{ C}}{0.920} = 5654\text{ C}

  4. Step 4

    t=45.0 min  ⟹  I=5654 C45.0 min=126 At = 45.0\text{ min} \implies I = \frac{5654\text{ C}}{45.0\text{ min}} = 126\text{ A}

    Correct

    t=45.0 min×60 s/min=2700 s  ⟹  I=5654.5 C2700 s≈2.09 At = 45.0\text{ min} \times 60\text{ s/min} = 2700\text{ s} \implies I = \frac{5654.5\text{ C}}{2700\text{ s}} \approx 2.09\text{ A}

    An ampere is defined as one coulomb per second (A=C/s\text{A} = \text{C/s}). By dividing coulombs by minutes without multiplying by 60 s/min60\text{ s/min}, your calculated current was a factor of 6060 too large.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly determined the amount of gold in moles using the given mass and molar mass.

You correctly identified that 33 moles of electrons are required per mole of Au3+\text{Au}^{3+} reduced.

You correctly divided the theoretical charge by the efficiency factor of 0.9200.920 to account for side reactions.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omitted time unit conversion (minutes to seconds)

You divided by 45.0 min45.0\text{ min} instead of converting to 2700 s2700\text{ s}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You overlooked the SI base unit definition of electric current (1 A=1 C/s1\text{ A} = 1\text{ C/s}), which requires all electrolysis time intervals to be expressed in seconds before applying I=Q/tI = Q/t.

REASONING PATH
Your ACEpath teacher’s suggested approach
Definition of the Ampere
  • 1 A=1 C/s1\text{ A} = 1\text{ C/s}

  • Always convert time to seconds (t (s)=t (min)×60t\text{ (s)} = t\text{ (min)} \times 60) before substituting into I=QtI = \frac{Q}{t} or Q=I⋅tQ = I \cdot t.

Sanity Check on Plating Current
  • Laboratory and small decorative plating setups typically draw currents on the order of 0.5 A0.5\text{ A} to 10 A10\text{ A}, not industrial smelter currents (>100 A>100\text{ A}).

  • If a small electroplating problem yields a current over 100 A100\text{ A}, immediately check if time was left in minutes or hours.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert the time duration to SI units: t=45.0 min×60 s/min=2700 st = 45.0\text{ min} \times 60\text{ s/min} = 2700\text{ s}.

  2. Compute the required electric current: I=Qactualt=5654 C2700 s≈2.094 AI = \frac{Q_{\text{actual}}}{t} = \frac{5654\text{ C}}{2700\text{ s}} \approx 2.094\text{ A}.

Final answer

I=2.09 AI = 2.09\text{ A}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the fundamental definition of electric current in SI units (1 A=1 C/s1\text{ A} = 1\text{ C/s}).

  • Practice two-step unit tracking where time conversion is explicitly written out as a separate factor before solving for II.

OverviewACEpath Teacher's Diagnosis

03 The student assumes a 1:1 electron-to-metal mole ratio instead of using z = 3 for the reduction of Au³⁺ ions.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    n(Au)=3.54 g196.97 g/mol=0.01797 moln(\text{Au}) = \frac{3.54\text{ g}}{196.97\text{ g/mol}} = 0.01797\text{ mol}

  2. Step 2

    t=45.0×60=2700 st = 45.0 \times 60 = 2700\text{ s}

  3. Step 3

    Qtheo=0.01797 mol×96485 C/mol=1734 CQ_{\text{theo}} = 0.01797\text{ mol} \times 96485\text{ C/mol} = 1734\text{ C}

    Correct

    Qtheo=n⋅z⋅F=0.01797 mol×3 mol e−/mol Au×96485 C/mol≈5202.2 CQ_{\text{theo}} = n \cdot z \cdot F = 0.01797\text{ mol} \times 3\text{ mol } e^-/\text{mol Au} \times 96485\text{ C/mol} \approx 5202.2\text{ C}

    You used a 1:11:1 ratio of electrons to gold atoms instead of multiplying by z=3z = 3 from the reduction half-reaction AuX3++3 eX−→Au\ce{Au^{3+} + 3e^- -> Au}.

  4. Step 4

    Qactual=1734 C0.920=1885 CQ_{\text{actual}} = \frac{1734\text{ C}}{0.920} = 1885\text{ C}

    Correct

    Qactual=Qtheoη=5202.2 C0.920≈5654.5 CQ_{\text{actual}} = \frac{Q_{\text{theo}}}{\eta} = \frac{5202.2\text{ C}}{0.920} \approx 5654.5\text{ C}

    Your method of dividing by the current efficiency η=0.920\eta = 0.920 is conceptually correct, but the value is affected by the missing factor of 33 in QtheoQ_{\text{theo}}.

  5. Step 5

    I=1885 C2700 s=0.698 AI = \frac{1885\text{ C}}{2700\text{ s}} = 0.698\text{ A}

    Correct

    I=Qactualt=5654.5 C2700 s≈2.09 AI = \frac{Q_{\text{actual}}}{t} = \frac{5654.5\text{ C}}{2700\text{ s}} \approx 2.09\text{ A}

    Your calculation of current using I=QtI = \frac{Q}{t} is carried out correctly, but the numerical answer inherits the error from Step 3.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the amount of gold in moles from its mass and molar mass.

You properly converted the electroplating time from minutes to seconds.

You correctly divided the theoretical charge by the current efficiency to obtain the total required charge.

You correctly applied the formula I=QtI = \frac{Q}{t} to find the current.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omission of valence factor (z) in Faraday's law

You treated the reduction of AuX3+\ce{Au^{3+}} as a 1-electron transfer rather than a 3-electron transfer.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Overlooking the stoichiometric number of electrons (zz) transferred per ion in the cathode half-reaction when relating moles of substance to Faraday's constant (Q=n⋅z⋅FQ = n \cdot z \cdot F).

REASONING PATH
Your ACEpath teacher’s suggested approach
Half-Reaction Electron Count
  • Every mole of metal deposited requires zz moles of electrons: Q=n⋅z⋅FQ = n \cdot z \cdot F.

  • Always write down the balanced cathode half-reaction and identify z=moles of e−z = \text{moles of } e^- transferred per mole of product before multiplying by Faraday's constant.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Include z=3z = 3 in the theoretical charge: Qtheo=0.017972 mol×3×96485 C/mol=5202.2 CQ_{\text{theo}} = 0.017972\text{ mol} \times 3 \times 96485\text{ C/mol} = 5202.2\text{ C}.

  2. Divide by the current efficiency: Qactual=5202.2 C0.920=5654.5 CQ_{\text{actual}} = \frac{5202.2\text{ C}}{0.920} = 5654.5\text{ C}.

  3. Calculate the current: I=5654.5 C2700 s≈2.094 AI = \frac{5654.5\text{ C}}{2700\text{ s}} \approx 2.094\text{ A}.

Final answer

I=2.09 AI = 2.09\text{ A}

NEXT STEPS
Final Takeaways from Your Teacher
  • Write out the balanced reduction half-reaction explicitly at the start of any electrolysis problem.

  • Highlight the coefficient of electrons (zz) to make sure it enters your charge equation Q=n⋅z⋅FQ = n \cdot z \cdot F.

Lock it in

Similar question

01

A silver-plating bath deposits Ag\ce{Ag} via AgX+(aq)+eX−→Ag(s)\ce{Ag+(aq) + e- -> Ag(s)}. To deposit 2.16 g2.16\text{ g} of silver (M=107.87 g/molM = 107.87\text{ g/mol}) in 20.0 min20.0\text{ min} at a cathode current efficiency of 88.0%88.0\%, what constant current must the power supply deliver? (Use F=96485 C/molF = 96485\text{ C/mol})

Answer

I=1.83 AI = 1.83\text{ A}. Key steps: nAg=2.16107.87≈0.02002 moln_{\ce{Ag}} = \frac{2.16}{107.87} \approx 0.02002\text{ mol}; Qtheoretical=0.02002×1×96485≈1932 CQ_{\text{theoretical}} = 0.02002 \times 1 \times 96485 \approx 1932\text{ C}; t=1200 st = 1200\text{ s}; Iuseful=19321200=1.61 AI_{\text{useful}} = \frac{1932}{1200} = 1.61\text{ A}; Iactual=1.610.880≈1.83 AI_{\text{actual}} = \frac{1.61}{0.880} \approx 1.83\text{ A}.

02

A nickel electroforming tank operates at a constant current of 12.5 A12.5\text{ A} for 1.50 hours1.50\text{ hours} with a current efficiency of 94.0%94.0\%. How many grams of metallic nickel (M=58.69 g/molM = 58.69\text{ g/mol}) are deposited at the cathode via NiX2+(aq)+2 eX−→Ni(s)\ce{Ni^{2+}(aq) + 2e- -> Ni(s)}?

Answer

m=19.3 gm = 19.3\text{ g}. Key steps: t=5400 st = 5400\text{ s}; Qtotal=12.5×5400=67500 CQ_{\text{total}} = 12.5 \times 5400 = 67500\text{ C}; Quseful=Qtotal×0.940=63450 CQ_{\text{useful}} = Q_{\text{total}} \times 0.940 = 63450\text{ C}; ne−=6345096485≈0.6576 moln_{e^-} = \frac{63450}{96485} \approx 0.6576\text{ mol}; nNi=0.65762≈0.3288 moln_{\ce{Ni}} = \frac{0.6576}{2} \approx 0.3288\text{ mol}; m=0.3288×58.69≈19.3 gm = 0.3288 \times 58.69 \approx 19.3\text{ g}.

03

An industrial zinc plating cell operates at I=25.0 AI = 25.0\text{ A} for 30.0 minutes30.0\text{ minutes} to reduce ZnX2+(aq)+2 eX−→Zn(s)\ce{Zn^{2+}(aq) + 2e- -> Zn(s)} (M=65.38 g/molM = 65.38\text{ g/mol}). If 13.2 g13.2\text{ g} of zinc is actually deposited, calculate the cathode current efficiency η\eta and identify where the remaining current was spent.

Answer

η=86.4%\eta = 86.4\%. Key steps: t=1800 st = 1800\text{ s}; Qtotal=25.0×1800=45000 CQ_{\text{total}} = 25.0 \times 1800 = 45000\text{ C}; nZn=13.265.38≈0.2019 moln_{\ce{Zn}} = \frac{13.2}{65.38} \approx 0.2019\text{ mol}; Qtheoretical=0.2019×2×96485≈38960 CQ_{\text{theoretical}} = 0.2019 \times 2 \times 96485 \approx 38960\text{ C}; η=38960 C45000 C≈0.864=86.4%\eta = \frac{38960\text{ C}}{45000\text{ C}} \approx 0.864 = 86.4\%. The remaining 13.6%13.6\% of current went into parasitic cathodic side reactions, predominantly hydrogen gas evolution (2HX+(aq)+2e−→HX2(g)2\ce{H+(aq)} + 2e^- \rightarrow \ce{H2(g)}).

Loading workspace…