Resources
A student assesses the hazards of a halogenated solvent rinse using the NFPA 704 standard and OSHA Permissible Exposure Limits (PEL). The process uses dichloromethane (, health hazard rating ) versus an alternative bio-derived solvent, ethyl lactate (health hazard rating ). A common convention trap is assuming that a higher numeric NFPA health rating implies a higher numerical PEL threshold value. Dichloromethane has an 8-hour time-weighted average (TWA) PEL of , whereas ethyl lactate has a recommended occupational exposure limit of . If an unventilated bench space of volume at and accidentally vaporizes of pure dichloromethane, calculate the equilibrium concentration of the contaminant in parts per million (, where ), and determine whether this concentration violates the OSHA PEL threshold.
Answer and steps
Final answer
; Violates OSHA PEL ()
Steps
Calculate the Vapor Volume of Dichloromethane
Assuming ideal gas behavior under ambient conditions (, ), use the ideal gas law to find the volume occupied by of vaporized dichloromethane ():
Using the ideal gas constant :
Convert the vapor volume into cubic meters () or milliliters ():
Determine the Concentration in Parts Per Million (ppm)
By definition, for gases dispersed in air at the same temperature and pressure, concentration in parts per million by volume () is given by:
Equivalently, since :
Evaluate Compliance with the OSHA PEL Threshold
- OSHA Permissible Exposure Limit (PEL): For dichloromethane, the PEL is as an 8-hour time-weighted average (TWA).
- Comparison: The resulting concentration of is far greater than the threshold limit:
Therefore, this concentration heavily violates the OSHA PEL threshold.
Hazard Convention Note: Do not confuse the NFPA 704 hazard rating with exposure limits such as the OSHA PEL:
- In NFPA 704, a higher number indicates a greater danger (, ).
- For PELs and TLVs, a lower numerical concentration threshold indicates a more hazardous/toxic substance because less exposure is legally or safely tolerated. Dichloromethane has a higher NFPA health rating () and correspondingly a much stricter, lower PEL threshold () than ethyl lactate.
Typical errors
01 A student incorrectly converts liters to milliliters by dividing by 1000 instead of multiplying, resulting in a concentration of 0.652 ppm and falsely concluding no violation occurs.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You divided by instead of multiplying. Because , converting from liters to milliliters requires multiplying by .
- Step 3Correct
This calculation was affected by the volume error from Step 2, and setting equal to also misapplied the given equivalence .
- Step 4Correct
Because your calculated concentration was three orders of magnitude too low, you reached the opposite compliance conclusion.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified and applied the ideal gas law to solve for the vapor volume.
You used the correct gas constant and temperature values for standard ambient conditions.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou divided the volume in liters by instead of multiplying by to convert to milliliters.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing prefix scaling when changing to smaller metric units (), which led to an artificially diluted concentration value that appeared safe.
REASONING PATH
Your ACEpath teacher’s suggested approach- Metric prefix direction check
Converting from a larger unit (L) to a smaller unit (mL) always results in a larger numerical value: .
Always write out explicit conversion factors with units cancelling, such as , before computing.
- Airborne concentration definition
For gas vapors in air, .
Ensure both numerator and denominator match the exact ratio definition without applying extra factors of .
CORRECTED PATH
ACEpath Teacher's DemonstrationConvert liters to milliliters: .
Calculate concentration using the volume of air: .
Compare with the OSHA PEL: , so the concentration severely exceeds the legal limit.
; Violates OSHA PEL ()
02 A student mistakenly compares the calculated concentration to the 100 ppm limit of ethyl lactate instead of dichloromethane's 25 ppm PEL.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3
, so this concentration violates the OSHA PEL threshold.
Correct, violating the OSHA PEL.
You crossed out the correct limit () and compared the concentration to , which is the exposure limit for ethyl lactate, not dichloromethane. While the qualitative conclusion happens to match because exceeds both values, evaluating compliance requires using the target contaminant's specific PEL.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the vaporized volume using the ideal gas law.
You accurately computed the concentration in parts per million by volume.
You recognized that a concentration exceeding the regulatory limit constitutes a violation.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou initially wrote the correct PEL of , but crossed it out and adopted the threshold of the alternative solvent.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the comparison solvent's limit with the target solvent's PEL, possibly influenced by the misconception that a higher NFPA health hazard rating corresponds to a larger exposure threshold. In reality, more hazardous substances have stricter, lower permissible exposure limits.
REASONING PATH
Your ACEpath teacher’s suggested approach- Match the Limit to the Specific Substance
Regulatory thresholds such as OSHA PELs are chemical-specific; always evaluate against the limit for the exact substance released.
Check that the threshold value corresponds to dichloromethane () rather than ethyl lactate ().
- Invert Hazard Scale vs. Threshold Scale
NFPA 704 ratings increase with hazard severity ( to ), but exposure limits decrease with toxicity (a lower PEL means lower tolerance).
Remember that a higher health rating ( vs. ) dictates a lower, more restrictive PEL ( vs. ).
- Explicitly Label Reference Values
When comparing multiple chemicals, writing down the compound name next to each threshold prevents accidental value swapping.
Write '' explicitly before making the inequality comparison.
CORRECTED PATH
ACEpath Teacher's DemonstrationIdentify the OSHA PEL for dichloromethane: .
Compare the calculated vapor concentration to the threshold: .
; Violates OSHA PEL ()
03 A student confuses ppm for gases (volume per volume) with parts per million for aqueous solutions (milligrams per liter) and calculates milligrams of solute per cubic meter of air.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You equated directly to parts per million. In air at ambient conditions, parts per million is a volume-to-volume ratio ( or ), not mass per unit volume.
- Step 3Correct
Your comparison logic and qualitative conclusion are sound, but this step uses the incorrect concentration calculated in Step 2.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the molar mass and total mass of dichloromethane.
You accurately identified the OSHA PEL threshold value of and drew the correct qualitative compliance conclusion.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou applied the dilute aqueous solution convention where to an airborne vapor mixture, mistakenly treating as parts per million rather than finding the vapor volume via the ideal gas law.
REASONING PATH
Your ACEpath teacher’s suggested approach- Gas Concentration Definition
For gases and vapors in air, is defined on a volume (or mole) basis: .
Always convert vaporized moles to gas volume using before dividing by room volume.
- Converting mg/m³ to ppm
At () and , the relationship is .
If you have mass concentration in , divide by molar mass and multiply by the standard molar volume () to obtain .
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate the vapor volume occupied by of using the ideal gas law: .
Compute the concentration in parts per million: .
Compare the calculated concentration to the OSHA PEL threshold: , which violates the OSHA PEL threshold.
; Violates OSHA PEL ()
Lock it in
When converting a volume from liters () to milliliters (), do you multiply or divide by ?
Multiply by (). A smaller unit requires a larger number.
Similar question
A laboratory space of volume has an accidental spill that releases of acetone vapor at and . Calculate the room concentration in () and determine if it exceeds the OSHA PEL of .
Answer
; Does not exceed OSHA PEL. Key steps: . .
An open bath in an unventilated room of evaporates of benzene (molar mass ) at and . The OSHA PEL for benzene is . Determine the resulting concentration in and assess whether it violates the PEL.
Answer
; Violates OSHA PEL. Key steps: . . .
A chemical synthesis bench has a target cap of for a reagent vapor. If the room volume is at and , calculate the maximum number of moles of the reagent that can evaporate into the room before violating this threshold.
Answer
. Key steps: . .