Resources
A solution contains of an organic non-electrolyte pharmaceutical agent dissolved in of pure ethanol. The density of pure ethanol is , its normal boiling point is , and its molal boiling point elevation constant is . If the measured boiling point elevation of the solution is , calculate the molar mass of the pharmaceutical agent in .
Answer and steps
Final answer
Steps
Calculate the mass of the solvent (ethanol) in kilograms
To find the molar mass of the pharmaceutical agent, we relate the measured boiling point elevation to the molality of the solution.
The volume and density of ethanol are given. Multiply the volume by density to find the mass in grams, then convert to kilograms:
Determine the molality of the solution
Boiling point elevation is a colligative property governed by the formula:
Because the solute is a non-electrolyte, it does not dissociate in solution, so the van 't Hoff factor is . Solving for molality ():
Common Pitfall: Be careful not to use molarity () instead of molality (). Colligative property formulas specifically depend on the mass of the solvent in kilograms, not the total volume of the solution.
Calculate the moles of solute
Molality represents the moles of solute per kilogram of solvent:
Calculate the molar mass of the solute
Convert the solute mass to grams:
Now, divide the mass of the solute by the number of moles:
Rounding to three significant figures gives .
Typical errors
01 The student forgets to use density to convert the volume of ethanol to mass, mistakenly assuming 50.00 mL equals 50.00 g as if the solvent were water.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You set directly equal to , which is only valid for water with a density of . For ethanol, you must multiply volume by its density () to find the mass.
- Step 2
- Step 3Correct
Your formula is correct, but your result was affected by the incorrect solvent mass from Step 1.
- Step 4
- Step 5Correct
You correctly set up the quotient , but the value is lower than expected because the moles value propagated from Step 1 was too large.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly used the boiling point elevation formula to solve for molality.
You converted milligrams to grams accurately.
You correctly recognized that molar mass is found by dividing solute mass in grams by solute moles.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou assumed that for ethanol, bypassing the density conversion.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou defaulted to water's familiar density shortcut instead of checking the solvent's specific density when converting volume to mass for molality.
REASONING PATH
Your ACEpath teacher’s suggested approach- Verify solvent identity and density
Molality requires the mass of the solvent in kilograms: .
Whenever a solvent volume is given in , look up or check the problem statement for the solvent's density before plugging mass into the molality equation.
CORRECTED PATH
ACEpath Teacher's DemonstrationUse the true solvent mass: .
Calculate moles of solute using the correct solvent mass: .
Divide solute mass by correct moles: .
02 The student forgets to convert the mass of the solute from milligrams to grams before dividing by moles.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3
- Step 4Correct
You used the solute mass directly as without converting it to grams (), causing your final molar mass to be off by a factor of .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly used density and volume to determine the mass of the solvent in kilograms.
You correctly applied the boiling point elevation formula to find the solution's molality.
You accurately calculated the amount of solute in moles from the molality and solvent mass.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou substituted the solute mass in milligrams () instead of grams () into the molar mass definition.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisInattention to dimensional consistency in compound units: because molar mass is expressed in , the mass in the numerator must be expressed in grams rather than milligrams.
REASONING PATH
Your ACEpath teacher’s suggested approach- Check Molar Mass Units
Molar mass has units of , which requires mass in grams: .
Always write explicit units next to numbers in your formulas to verify that units cancel and produce .
CORRECTED PATH
ACEpath Teacher's DemonstrationConvert the given mass of the solute from milligrams to grams: .
Divide the converted mass by the moles of solute: .
Round to three significant figures: .
03 The student misapplies the boiling point elevation formula by inverting the relation, calculating molality as Kb / ΔTb instead of ΔTb / Kb.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
The boiling point elevation relationship is . Rearranging for molality gives , not .
- Step 3Correct
Your method of multiplying molality by the solvent mass in kilograms is correct, but the calculation inherits the inverted molality value from Step 2.
- Step 4Correct
You correctly converted milligrams to grams and divided mass by moles, but the final answer is thrown off by the earlier calculation error.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly determined the mass of the solvent in kilograms using its volume and density.
You accurately converted the solute mass from milligrams to grams.
You used the correct conceptual relationships connecting molality to moles and moles to molar mass.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou accidentally swapped the numerator and denominator when solving for molality.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisIsolating a variable from a product requires dividing both sides by the coefficient (), rather than dividing the constant by the observed change.
REASONING PATH
Your ACEpath teacher’s suggested approach- Dimensional Analysis Check
Molality has units of , while has units of .
Check that yields before proceeding with downstream steps.
- Reasonableness of Result
Organic pharmaceutical molecules typically have molar masses between and several hundred .
If your calculated molar mass is unrealistically small (like , lighter than helium), re-check whether your molality was accidentally inverted.
CORRECTED PATH
ACEpath Teacher's DemonstrationSolve for molality using .
Find moles of solute: .
Calculate molar mass: .
Lock it in
How do you calculate the mass of solvent (in ) when given solvent volume in and density in ?
. Multiply volume by density first, then convert grams to kilograms.
Similar question
A solution is prepared by dissolving of a non-electrolyte in of benzene (density , ). If , calculate the molar mass of the solute in .
Answer
. Molality . Moles of solute . Molar mass .
A chemist dissolves of an unknown non-volatile solid in of chloroform (density , ). The boiling point increases by . Determine the molar mass of the solid.
Answer
. Molality . Moles of solute . Molar mass .
A student measures after dissolving of an organic compound in of diethyl ether (density , ). If the student mistakenly uses as the solvent mass instead of applying density, by what percentage will their calculated molar mass differ from the true molar mass?
Answer
True solvent mass is . Since , calculated molar mass is inversely proportional to solvent mass: . The student's calculated value will be too low (a error).