Resources

A clean glass capillary tube with an internal radius of r=0.250 mmr = 0.250\text{ mm} is held vertically in a beaker of pure water at 20.0∘C20.0^\circ\text{C}, where water exhibits a surface tension of γ=7.28×10−2 N/m\gamma = 7.28\times 10^{-2}\text{ N}/\text{m}, a density of ρ=998 kg/m3\rho = 998\text{ kg}/\text{m}^3, and a contact angle of θ=0.00∘\theta = 0.00^\circ due to favorable hydrogen-bonding adhesion with the hydrophilic glass walls. Calculate the maximum equilibrium height hh (in centimeters) to which the water column rises against Earth's gravitational acceleration (g=9.81 m/s2g = 9.81\text{ m}/\text{s}^2). Express your answer to three significant figures.

Answer and steps

Final answer

5.95 cm5.95\text{ cm}

Steps

Understanding Capillary Rise (Jurin's Law)

When a narrow, clean glass capillary is placed vertically into water, adhesive forces between the polar water molecules and the hydrophilic silanol (−Si−OH\ce{-Si-OH}) groups on the glass wall cause water to wet the glass surface (θ=0.00∘\theta = 0.00^\circ). The upward vertical component of the surface tension force pulls the liquid column upward until it is balanced by the downward gravitational weight of the liquid column.

  1. Upward force from surface tension: The surface tension acts along the perimeter of the circular contact line of radius rr: Fup=2πrγcos⁡θF_{\text{up}} = 2\pi r \gamma \cos\theta
  2. Downward force due to gravity: The weight of the elevated cylinder of liquid of height hh and cross-sectional area πr2\pi r^2 is: Fdown=mg=(ρV)g=ρ(πr2h)gF_{\text{down}} = m g = (\rho V) g = \rho (\pi r^2 h) g
  3. Equilibrium condition: At maximum capillary rise, the upward and downward forces balance: 2πrγcos⁡θ=ρπr2hg2\pi r \gamma \cos\theta = \rho \pi r^2 h g

    Solving for the capillary rise height hh gives Jurin's Law: h=2γcos⁡θρgrh = \frac{2\gamma \cos\theta}{\rho g r}


Step-by-Step Calculation

  1. Convert all values to consistent SI units:

    • Radius: r=0.250 mm=0.250×10−3 m=2.50×10−4 mr = 0.250\text{ mm} = 0.250 \times 10^{-3}\text{ m} = 2.50 \times 10^{-4}\text{ m}
    • Surface tension: γ=7.28×10−2 N/m\gamma = 7.28 \times 10^{-2}\text{ N/m}
    • Density: ρ=998 kg/m3\rho = 998\text{ kg/m}^3
    • Acceleration due to gravity: g=9.81 m/s2g = 9.81\text{ m/s}^2
    • Contact angle: θ=0.00∘  ⟹  cos⁡(0.00∘)=1\theta = 0.00^\circ \implies \cos(0.00^\circ) = 1
  2. Substitute values into the formula: h=2⋅(7.28×10−2 N/m)⋅1(998 kg/m3)⋅(9.81 m/s2)⋅(2.50×10−4 m)h = \frac{2 \cdot (7.28 \times 10^{-2}\text{ N/m}) \cdot 1}{(998\text{ kg/m}^3) \cdot (9.81\text{ m/s}^2) \cdot (2.50 \times 10^{-4}\text{ m})}
  3. Evaluate the numerator and denominator: Numerator=2⋅7.28×10−2=0.1456 N/m\text{Numerator} = 2 \cdot 7.28 \times 10^{-2} = 0.1456\text{ N/m} Denominator=998⋅9.81⋅2.50×10−4≈2.4476 kg/(m2⋅s2)\text{Denominator} = 998 \cdot 9.81 \cdot 2.50 \times 10^{-4} \approx 2.4476\text{ kg}/(\text{m}^2\cdot\text{s}^2)
  4. Calculate hh in meters: h=0.14562.4476≈0.059487 mh = \frac{0.1456}{2.4476} \approx 0.059487\text{ m}
  5. Convert height to centimeters: h=0.059487 m×100 cm/m≈5.95 cmh = 0.059487\text{ m} \times 100\text{ cm/m} \approx 5.95\text{ cm}

Common Pitfall: Forgetting to convert the capillary radius from millimeters to meters before performing the calculation will cause the result to be off by a factor of 10310^3. Always ensure all base units are in standard SI form (m\text{m}, kg\text{kg}, s\text{s}) prior to evaluating.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets the factor of 2 in Jurin's law, resulting in half the actual capillary rise height.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    h=γcos⁡θρgrh = \frac{\gamma \cos\theta}{\rho g r}

    Correct

    h=2γcos⁡θρgrh = \frac{2\gamma \cos\theta}{\rho g r}

    You missed the factor of 22 in the numerator. The upward capillary force acts along the tube circumference (2πrγcos⁡θ2\pi r \gamma \cos\theta) while the downward gravitational weight acts on the cross-sectional area (πr2ρgh\pi r^2 \rho g h). Equating the two yields h=2γcos⁡θρgrh = \frac{2\gamma \cos\theta}{\rho g r}.

  2. Step 2

    r=0.250 mm=2.50×10−4 m  ⟹  cos⁡(0∘)=1r = 0.250\text{ mm} = 2.50 \times 10^{-4}\text{ m} \implies \cos(0^\circ) = 1

  3. Step 3

    h=7.28×10−2×1998×9.81×2.50×10−4h = \frac{7.28 \times 10^{-2} \times 1}{998 \times 9.81 \times 2.50 \times 10^{-4}}

    Correct

    h=2×(7.28×10−2)×1998×9.81×2.50×10−4h = \frac{2 \times (7.28 \times 10^{-2}) \times 1}{998 \times 9.81 \times 2.50 \times 10^{-4}}

    Your numerical substitution is carried out accurately according to your formula, but it inherits the missing factor of 22 from Step 1.

  4. Step 4

    h=0.0297 m=2.97 cmh = 0.0297\text{ m} = 2.97\text{ cm}

    Correct

    h≈0.0595 m=5.95 cmh \approx 0.0595\text{ m} = 5.95\text{ cm}

    Your calculation and unit conversion to centimeters are internally consistent with your working, but the value is half of the correct height because of the initial formula error.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified the relevant physical variables including surface tension, density, gravitational acceleration, and radius.

You properly converted the tube radius from millimeters to meters (2.50×10−4 m2.50 \times 10^{-4}\text{ m}).

You correctly evaluated cos⁡(0∘)=1\cos(0^\circ) = 1 for complete wetting.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omitted factor of 2 in Jurin's law

You set the capillary rise equation as h=γcos⁡θρgrh = \frac{\gamma \cos\theta}{\rho g r} rather than h=2γcos⁡θρgrh = \frac{2\gamma \cos\theta}{\rho g r}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You likely forgot how the geometry balances: surface tension pulls along the perimeter (2πr2\pi r), while gravity pulls down the volume over the cross-sectional area (πr2\pi r^2). Dividing the perimeter by the area leaves a factor of 2r\frac{2}{r}, not 1r\frac{1}{r}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Deriving Jurin's Law from Force Balance
  • Upward surface tension force is Fup=2πrγcos⁡θF_{\text{up}} = 2\pi r \gamma \cos\theta, and downward weight is Fdown=ρ(πr2h)gF_{\text{down}} = \rho (\pi r^2 h) g.

  • Always write down the force balance 2πrγcos⁡θ=ρπr2hg2\pi r \gamma \cos\theta = \rho \pi r^2 h g and cancel πr\pi r to verify the factor of 22 in the numerator.

Pressure Jump Form
  • Laplace pressure across a spherical meniscus of radius R=rcos⁡θR = \frac{r}{\cos\theta} is ΔP=2γR=ρgh\Delta P = \frac{2\gamma}{R} = \rho g h.

  • Remember that a spherical surface has two principal radii of curvature, producing a factor of 22 in the Laplace pressure.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Apply Jurin's law including the factor of 22: h=2γcos⁡θρgrh = \frac{2\gamma \cos\theta}{\rho g r}.

  2. Substitute the given values: h=2×(7.28×10−2 N/m)×1(998 kg/m3)(9.81 m/s2)(2.50×10−4 m)h = \frac{2 \times (7.28 \times 10^{-2}\text{ N/m}) \times 1}{(998\text{ kg/m}^3)(9.81\text{ m/s}^2)(2.50 \times 10^{-4}\text{ m})}.

  3. Calculate the height in meters: h≈0.14562.4476≈0.05949 mh \approx \frac{0.1456}{2.4476} \approx 0.05949\text{ m}.

  4. Convert to centimeters and round to three significant figures: h=5.95 cmh = 5.95\text{ cm}.

Final answer

5.95 cm5.95\text{ cm}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the force-balance derivation of capillary rise to solidify why the factor of 22 appears from the ratio of circumference (2πr2\pi r) to cross-sectional area (πr2\pi r^2).

  • Practice expressing Jurin's law in both radius form (h=2γcos⁡θρgrh = \frac{2\gamma\cos\theta}{\rho g r}) and diameter form (h=4γcos⁡θρgdh = \frac{4\gamma\cos\theta}{\rho g d}).

  • Complete the three targeted practice exercises below to build confidence with capillary rise calculations.

OverviewACEpath Teacher's Diagnosis

02 The student treats the given internal radius as the tube diameter and divides it by 2, doubling the calculated height.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    h=2γcos⁡θρgrh = \frac{2\gamma \cos\theta}{\rho g r}

  2. Step 2

    r=0.250 mm2=0.125 mm=1.25×10−4 mr = \frac{0.250\text{ mm}}{2} = 0.125\text{ mm} = 1.25\times 10^{-4}\text{ m}

    Correct

    r=0.250 mm=2.50×10−4 mr = 0.250\text{ mm} = 2.50\times 10^{-4}\text{ m}

    The problem explicitly provided the internal radius as r=0.250 mmr = 0.250\text{ mm}. You divided this value by 22 as if it were a diameter, halving the radius to 1.25×10−4 m1.25\times 10^{-4}\text{ m}.

  3. Step 3

    h=2×7.28×10−2×1998×9.81×1.25×10−4  ⟹  h=0.14561.224h = \frac{2 \times 7.28 \times 10^{-2} \times 1}{998 \times 9.81 \times 1.25 \times 10^{-4}} \implies h = \frac{0.1456}{1.224}

    Correct

    h=2×(7.28×10−2 N/m)×1(998 kg/m3)(9.81 m/s2)(2.50×10−4 m)≈0.14562.4476h = \frac{2 \times (7.28 \times 10^{-2}\text{ N/m}) \times 1}{(998\text{ kg/m}^3)(9.81\text{ m/s}^2)(2.50 \times 10^{-4}\text{ m})} \approx \frac{0.1456}{2.4476}

    Your substitution and arithmetic were carried out consistently with your halved radius, but the value in the denominator was affected by the earlier error.

  4. Step 4

    h=0.119 m=11.9 cmh = 0.119\text{ m} = 11.9\text{ cm}

    Correct

    h≈0.0595 m=5.95 cmh \approx 0.0595\text{ m} = 5.95\text{ cm}

    Because the radius was halved, your calculated height is twice the expected equilibrium height of 5.95 cm5.95\text{ cm}.

WHAT YOU DID WELL
Compliments from Your Teacher

You selected the correct formula for capillary rise, Jurin's law.

You correctly used cos⁡(0.00∘)=1\cos(0.00^\circ) = 1 for complete wetting.

You handled standard metric prefix conversion from millimeters to meters accurately.

You correctly converted your final height from meters to centimeters.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Radius versus Diameter Confusion

You divided the given dimension by 2 even though the problem statement explicitly gave the internal radius rather than the diameter.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Automatic habit of dividing given geometric dimensions by 2: in many physics and chemistry problems, circular tube dimensions are given as diameters, leading to an automatic reaction to divide by 2 without verifying whether the text specifies 'radius' or 'diameter'.

REASONING PATH
Your ACEpath teacher’s suggested approach
Check Problem Wording for Radius vs. Diameter
  • Jurin's law requires tube radius rr. If the problem already states 'radius', use it directly; only divide by 22 if the problem states 'diameter' (d=2rd = 2r).

  • Circle or underline the word 'radius' or 'diameter' in the prompt before extracting numerical values into your variable list.

Inverse Relationship Sanity Check
  • Capillary height is inversely proportional to radius (h∝1rh \propto \frac{1}{r}). Halving the radius doubles the expected height.

  • Ensure that doubling or halving radius produces physically sensible changes and verify that you did not introduce an unintended factor of 22.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Extract the given radius: r=0.250 mm=2.50×10−4 mr = 0.250\text{ mm} = 2.50 \times 10^{-4}\text{ m}.

  2. Substitute into Jurin's law: h=2(7.28×10−2 N/m)(1)(998 kg/m3)(9.81 m/s2)(2.50×10−4 m)h = \frac{2(7.28 \times 10^{-2}\text{ N/m})(1)}{(998\text{ kg/m}^3)(9.81\text{ m/s}^2)(2.50 \times 10^{-4}\text{ m})}.

  3. Evaluate the denominator: 998×9.81×2.50×10−4≈2.4476 kg/(m2⋅s2)998 \times 9.81 \times 2.50 \times 10^{-4} \approx 2.4476\text{ kg}/(\text{m}^2\cdot\text{s}^2).

  4. Calculate h=0.14562.4476≈0.059487 m=5.95 cmh = \frac{0.1456}{2.4476} \approx 0.059487\text{ m} = 5.95\text{ cm}.

Final answer

5.95 cm5.95\text{ cm}

NEXT STEPS
Final Takeaways from Your Teacher
  • Read given geometric parameters carefully to distinguish between radius and diameter before writing down variables.

  • Practice problems with mixed dimensional specifications (some providing inner diameter, others providing internal radius).

  • Double-check that the denominator in Jurin's law uses rr, or replace rr with d/2d/2 to write h=4γcos⁡θρgdh = \frac{4\gamma \cos\theta}{\rho g d} when diameter is given.

OverviewACEpath Teacher's Diagnosis

03 The student substitutes the radius in millimeters directly into SI units without converting to meters, yielding a height that is off by a factor of 1000.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    h=2γcos⁡θρgrh = \frac{2\gamma \cos\theta}{\rho g r}

  2. Step 2

    h=2×7.28×10−2×1998×9.81×0.250h = \frac{2 \times 7.28 \times 10^{-2} \times 1}{998 \times 9.81 \times 0.250}

    Correct

    h=2×(7.28×10−2 N/m)×cos⁡(0.00∘)(998 kg/m3)×(9.81 m/s2)×(2.50×10−4 m)h = \frac{2 \times (7.28 \times 10^{-2}\text{ N/m}) \times \cos(0.00^\circ)}{(998\text{ kg/m}^3) \times (9.81\text{ m/s}^2) \times (2.50 \times 10^{-4}\text{ m})}

    You plugged in r=0.250r = 0.250 directly instead of converting the radius from millimeters to meters (r=0.250 mm=2.50×10−4 mr = 0.250\text{ mm} = 2.50 \times 10^{-4}\text{ m}).

  3. Step 3

    h=0.14562447.6  ⟹  h=5.95×10−5 m=0.00595 cmh = \frac{0.1456}{2447.6} \implies h = 5.95 \times 10^{-5}\text{ m} = 0.00595\text{ cm}

    Correct

    h=0.14562.4476≈0.0595 m=5.95 cmh = \frac{0.1456}{2.4476} \approx 0.0595\text{ m} = 5.95\text{ cm}

    Your arithmetic followed correctly from the substituted values, but your final answer is off by a factor of 10001000 due to the unit error in Step 2.

WHAT YOU DID WELL
Compliments from Your Teacher

You chose the correct capillary rise formula (Jurin's Law).

You correctly recognized that a contact angle of θ=0.00∘\theta = 0.00^\circ gives cos⁡θ=1\cos\theta = 1.

You accurately converted between meters and centimeters in your final step.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Unit Conversion Omission

You entered the radius directly as 0.2500.250 without converting millimeters to base SI meters.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Jurin's Law combines base SI units (N/m\text{N/m}, kg/m3\text{kg/m}^3, m/s2\text{m/s}^2). When length parameters like radius are given in millimeters (mm\text{mm}), failing to convert them to meters (m\text{m}) scales the denominator by 10310^3, reducing the resulting height by three orders of magnitude.

REASONING PATH
Your ACEpath teacher’s suggested approach
SI Unit Consistency Check
  • Before substituting into equations involving derived SI units like Newtons (N=kg⋅m/s2\text{N} = \text{kg}\cdot\text{m}/\text{s}^2), all linear dimensions must be converted to base meters (m\text{m}).

  • Write out each variable with explicit units and convert them prior to calculation: r=0.250 mm=2.50×10−4 mr = 0.250\text{ mm} = 2.50 \times 10^{-4}\text{ m}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert the capillary radius to meters: r=0.250 mm=2.50×10−4 mr = 0.250\text{ mm} = 2.50 \times 10^{-4}\text{ m}.

  2. Substitute all variables in standard SI units: h=2×7.28×10−2 N/m×1998 kg/m3×9.81 m/s2×2.50×10−4 mh = \frac{2 \times 7.28 \times 10^{-2}\text{ N/m} \times 1}{998\text{ kg/m}^3 \times 9.81\text{ m/s}^2 \times 2.50 \times 10^{-4}\text{ m}}.

  3. Evaluate the denominator: 998×9.81×2.50×10−4≈2.4476 kg/(m2⋅s2)998 \times 9.81 \times 2.50 \times 10^{-4} \approx 2.4476\text{ kg}/(\text{m}^2\cdot\text{s}^2).

  4. Compute the height in meters: h=0.14562.4476≈0.05949 mh = \frac{0.1456}{2.4476} \approx 0.05949\text{ m}.

  5. Convert to centimeters: h=0.05949 m×100 cm/m≈5.95 cmh = 0.05949\text{ m} \times 100\text{ cm/m} \approx 5.95\text{ cm}.

Final answer

5.95 cm5.95\text{ cm}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always write out all given variables with their explicit units before plugging numbers into a formula.

  • Check that all length quantities are in meters whenever working with surface tension (N/m\text{N/m}) or density (kg/m3\text{kg/m}^3).

  • Perform a quick physical sanity check: a narrow capillary of radius 0.25 mm0.25\text{ mm} typically draws water several centimeters high, whereas 0.006 cm0.006\text{ cm} would be almost imperceptible.

Lock it in

Similar question

01

A capillary tube with radius r=0.500 mmr = 0.500\text{ mm} is immersed in ethanol (γ=2.23×10−2 N/m\gamma = 2.23 \times 10^{-2}\text{ N/m}, ρ=789 kg/m3\rho = 789\text{ kg/m}^3, θ=0.00∘\theta = 0.00^\circ, g=9.81 m/s2g = 9.81\text{ m/s}^2). Calculate the capillary rise hh in centimeters to three significant figures.

Answer

1.15 cm1.15\text{ cm}. Using h=2γcos⁡θρgrh = \frac{2\gamma \cos\theta}{\rho g r}, h=2(2.23×10−2)(1)(789)(9.81)(5.00×10−4)=0.01152 m=1.15 cmh = \frac{2(2.23 \times 10^{-2})(1)}{(789)(9.81)(5.00 \times 10^{-4})} = 0.01152\text{ m} = 1.15\text{ cm}.

02

A vertical glass capillary with an internal diameter of 0.120 mm0.120\text{ mm} is placed in water at 20∘C20^\circ\text{C} (γ=7.28×10−2 N/m\gamma = 7.28 \times 10^{-2}\text{ N/m}, ρ=998 kg/m3\rho = 998\text{ kg/m}^3, θ=0.00∘\theta = 0.00^\circ, g=9.81 m/s2g = 9.81\text{ m/s}^2). Calculate the equilibrium height of the water column in centimeters to three significant figures.

Answer

24.8 cm24.8\text{ cm}. Radius r=0.0600 mm=6.00×10−5 mr = 0.0600\text{ mm} = 6.00 \times 10^{-5}\text{ m}. Using h=2γcos⁡θρgrh = \frac{2\gamma \cos\theta}{\rho g r}, h=2(7.28×10−2)(1)(998)(9.81)(6.00×10−5)=0.2479 m=24.8 cmh = \frac{2(7.28 \times 10^{-2})(1)}{(998)(9.81)(6.00 \times 10^{-5})} = 0.2479\text{ m} = 24.8\text{ cm}.

03

Liquid mercury (γ=0.485 N/m\gamma = 0.485\text{ N/m}, ρ=13.53×103 kg/m3\rho = 13.53 \times 10^3\text{ kg/m}^3) has a contact angle of θ=140.0∘\theta = 140.0^\circ against clean glass. Calculate the capillary depression hh (in millimeters) in a tube of radius r=1.00 mmr = 1.00\text{ mm} with g=9.81 m/s2g = 9.81\text{ m/s}^2. Express your answer as a positive magnitude to three significant figures.

Answer

5.60 mm5.60\text{ mm}. Using h=2γ∣cos⁡θ∣ρgrh = \frac{2\gamma |\cos\theta|}{\rho g r}, h=2(0.485)∣cos⁡(140.0∘)∣(13530)(9.81)(1.00×10−3)=2(0.485)(0.7660)132.73≈5.60×10−3 m=5.60 mmh = \frac{2(0.485)|\cos(140.0^\circ)|}{(13530)(9.81)(1.00 \times 10^{-3})} = \frac{2(0.485)(0.7660)}{132.73} \approx 5.60 \times 10^{-3}\text{ m} = 5.60\text{ mm}.

Loading workspace…